I am about to replace the intake manifold and gaskets. I know all of that process, but first question is if there is anything i should do whilst in there. Second question; what can I do with my intake to get more power? Mainly just kind of wondering before I get my parts ordered.
View 4 RepliesI have a 1998 chevy silverado z/71 4x4. I had a water leak and had the intake manifold gaskets replaced. Ever since then, the check engine light comes on and it soots up the o2 sensors and the 4 plugs on the right bank. It may run good for a month or so and then it starts all over again.
View 1 RepliesI have a 2001 F150 Super Crew 5.4. I had a leak where the water transfer connects to the intake manifold. I decided to get a new manifold rather than trying to repair it. The new manifold from Dorman came and the gaskets were built into the manifold. I torqued the manifold to specs. I replaced everything and it starts fine.
I can hear what sounds like a leak, but can't find anything. I checked every hose that is connected and they are all snug and connected. I had the check engine light checked and it said it was running lean on both sides (p0174, p0171). Also a p0122. I thought something might have damaged the Throttle Body Position Sensor, so I replaced it...but no change.
I'm still driving it everyday because I need to. It won't change gears so smoothly sometimes. The most noticeable problem is that the A/C doesn't work. It just blows hot air. And the worst part about it is...it does it even when the air isn't turned on! I just go around with the windows down...in 95+ degree heat...with hot air blowing!
This is my first time to attempt a manifold change out. What I should check?
I have a 1999 Ford Expedition. A couple of days ago The engine started losing coolant as soon as the engine cooled. I replaced the coolant only to lose it again when the engine cooled. I was told that it is more likely the intake manifold gaskets leaking. It seems they are right. What is the cost to repair if I take it to a mechanic?
View 1 RepliesI took my Monte in for the annual Missouri Safety Inspection. Note: I had no known problems with my 2003 Monte SS 117K Miles. After the inspection, which passed, I was informed of a variety of problems: Intake Manifold Gasket Replacement, Valve Cover Gasket w/Intake replacement, Thermostat w/Intake Removal, Fuel Injector O-Rings w/Intake Removal.
My question is should I have all of this done? It's not cheap..roughly 1000 bucks. I know very little about this and I don't want to just tell my mechanic to do it without some research. Are these common problems with Monte's of this age/mileage and just part of the cost of owning this car. I am the original owner and have avoiding costly repairs/maintenance..it's been a great car.
I've got a 1997 F150 with the 4.2L V6. Before I got it last summer I did some research, but apparently missed the issue with the intake manifold gasket leaks on these early engines. It seems to be a very slow leak, but obviously I want to get it fixed. I called Ford to see if it had had the recall work done on it, but all they could tell me is that there wasn't an open recall on my truck (with the exception of the recent fuel tank strap recall). Their system apparently only goes back 10 years, so they couldn't even see the freakin' recall. So, I've got a few questions:
1) I know I didn't post much info, but does this seem like an intake manifold leak?
2) Are there any special tools needed to change out the gasket myself?
3) Can you all recommend any replacement gaskets? I found a few different manufacturers of gaskets, but I'm sure some are better than others.
4) Can this issue cause the computer to throw the loose gas cap code (P0455 if I recall correctly).
5) Would it be worth it to just get a new truck? I really wanted a diesel in the first place, but I also hate to give up on a nice truck with only 115,000 miles.
Replaced head gaskets on 2003 f-150 5.4. Now I can hear a ticking noise in middle of intake by #5 port. Maybe timing is off 1 link?
View 4 Repliesso new motor new intake , rear passenger side decides to leak when roughly about 10 degrese or lower and being -13 yesterday and-18 this morning.
last year it did this n i put a nother hose clamp on that rear tube and just happened to stop . n now back but the ting is that its not wet at all at the hose but at top of head bottom intake hmm . this is all just during the initial start of truck stops even before truck really gets warm
if i tke it off n its messed up i hope its warrentied even though i painted it. if fine i guess add some gasket maker ?
I was replacing my spark plugs and one screw holding the ignition coil stripped while another snapped. I have change 3 plugs (the easy one) and could have more problems. I spent half a day trying to drill the screws out to no avail and also noticed the intake manifold is plastic. I was thinking of swapping it out. This would alleviate the broken screw problem and make pulling the plugs easier. It also looks like it's just 8 bolts. Would swapping a new intake manifold in add any performance gains? Is there a manifold others recommend?
View 9 Repliesjust got finished putting her back together from a blown intake manifold gasket and run for a few miles to get rid of any cob webs and then my battery light comes on. just replaced the battery last week. and I tested the alternator and it charging at 14.5 volts bat reads when disconnected 12.9 volts so I am not sure why my battery light will come on.
View 14 RepliesI have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 Replies I have a 97 f350 crew cab xl stock everything. 351 windsor in it I do believe. as of right now He is broken down pulled apart in my garage. Due to a much requested headgasket replacement. In any event long story short I got him all apart to discover that there was someone in it before me & had broken the infamous exhaust manifold bolts (5) and two of the lower intake bolts, (of course I've tried the correct route in removing these broken bolts/studs but again the year of the truck (1997) & its bone stock no way their moving...
So of course I tried the next best thing (on a budget) which is to drill them out, but I went to far into the exhaust manifold bolt holes, And now I believe that I've ruined the heads is this so? If so who knows where i can get a decent set of bolt on heads ready to go. yes this is my daily driver & since He's been down I've been going deeper in dept.
Looking for any pictures or directions on replacing the intake manifold on the 2004 F150, 5.4. Got all the parts with the pulgs, and ignition coils.
View 6 RepliesI have a 97 ford f150 with a 5.4 I bought the truck with 114000 miles on it and the exhaust manifold bolts were broke from the exhaust I have replace the whole manifold with new gaskets and bolts and I get the codes 1131 and 1151 which indicates o2 sensors indicate lean and I also get p0136 and p0153 which indicate lean or front o2 sensors it will stay running for a little bit every once in a while but it only idles at 200 to 400 rpms and I'm not sure what to do?
View 4 Replies2003 F150 4.6 - I'm currently replacing the passenger side manifold studs. How the heck do you get to the bottom bolts? Looks like the motor mount is in the way. There's way more room on the 5.4s...
View 4 RepliesI have a 98 f150 4.6 4x4 with 175.000 miles, I suspected the intake gasket is leaking, I'v never done this before. What is involved with this type of repair? Will the intake gasket leak bad enough to leak antifreeze on the floor? Is it okay to continue to drive with this problem? Bad weather is on the way.
View 7 RepliesAbout to do the exhaust manifold gaskets on my 03 f250.
View 3 RepliesJust today,when replacing the UIM on a naturally aspirated 95 Pontiac Bonneville 3.8 with a Dorman upgraded type from my local auto parts, I ran into an issue. When following specified torquing sequences and specs , be very careful with the 1 long stud (#7), as it will split your new manifold there if you try to torque to 89 in/lbs. Took 1st back for replacement ,and the second new one started to split at the same place. Was using a brand new Craftsman in/lb torque wrench set correctly and following instructions exactly. I've seen a lot of excellent info on this UIM issue with the GM 3.8 ltr 1995-2004 years, but never this issue with the replacement ones. If I have to change this again will definitely go with the aluminum one.
View 1 RepliesI have had a problem with my car idle hunting for about the past year. Last week my car threw a code and my code checker said that all 4 cylinders were misfiring. So I am still under warranty and took the car to the dealer. They said the intake manifold was leaking.
Two questions come to mind: Has to engine suffered any damage from leaking for over a year? and Do they automatically change the oil when changing out the intake manifold/gasket?
I did have an oil analysis last year (5/11) through Blackstone Labs and no antifreeze was present in the oil but the silicates were mildly high. Car is a 2005 toyota corolla with 102,xxx miles. The dealer also did the head gasket and a couple other engine gaskets 1 year ago.
What are signs the intake manifold may be cracked? 2001 V10 Excursion....
View 4 RepliesI have a 77 bronco with a 5.0 efi engine from a 97 Ford Explorer. I noticed there is oil in the cold air intake area and upper intake manifold. I was checking on things and noticed oil around the PCV valve and on the outside of the cold air intake system. Should I be concerned about this? I have done some research. I checked the PCV valve and intake manifold gasket which appear to look fine.
The PCV valve rattles and the gasket is intact. Granted there isn't a lot of oil when I looked inside the upper intake manifold but thought I should write and ask if this is a problem or not. Should I just replace them pcv valve any ways and recheck it after driving it for a few miles? The explorer did have 110K on it but when we took it apart we thought the engine looked great for how many miles it had on it. We did change out the cam and timing chain but as far as the other parts, we did not replace.
I am also getting a unusual reading to not reading with my oil gauge. When driving for a about 30 minutes or so, My oil gauge goes down to zero when I'm stopped but when I'm drive off then the pressure comes back up. When I have it in park the gauge reads fine.