Ford F-150 - 1997-2003 :: 2001 - 4x4 Not Locking / Front Axle Is Not Pulling In When Switch The Selector On Dash
Feb 19, 2013
I have a 2001 f150 4x4 with the 4.6 Triton motor, the front axle is not pulling in when I switch the selector on the dash, I know the transfer case is switching so that part is ok. I know there are 2 solenoids on the fire wall, my question is which one is which ? every store I call says one has the nub at 9 o' clock and one at 6 o' clock which one of these does the front axle, don't want to order the wrong one ? I checked the vacuum and the blue line going to the axle always has vacuum and as I read the diagram the blue line is 2 wd and the red line is 4 wd so is the 2wd solenoid stuck and preventing the 4wd one from pulling in or is the 4wd one bad ?
View 4 Replies
Advertisement
I am needing to replace the selector switch for my 4x4 on my 2003 F150 Lariat FX4... I already have the new switch. Whats the best way to get in there to remove and replace the switch?
View 7 Replies
2002 F150 XL... My heat & AC work fine, but the only position the fan selector switch will actually blow any air is on high. Bought an OEM replacement switch and installed it but the issue still exists.
View 4 Replies
My selector switch does not light up when engaging four wheel drive on my 98 f150,could this be my GEM module gone bad ?
View 6 Replies
2001 F150 SCAB with 74,000 miles. There seems to be a whistling noise coming from the front axle. It is definately a rolling noise. I can shift into neutral and put it in 4H and still have the noise. Brakes are good, tires are fair... I just rotated my tires (criss-crossed front to back) also sprayed all of my boots with silicone spray. Still has a whistling metal to metal bearing sound. When I have the front jacked up and spin the wheels, there seems to be a decent drag turning by hand. I don't remember having much of a drag before.
View 6 Replies
When I turn the switch on the front wheels don't engage. I replaced the two vacuum solenoids on the firewall no change. I replaced the actuator motor on the transfer case and everything worked....once. Tried to go around the back of the house thought I was in 4x4 but front wheels not engaging again. buried in mud. I let it set there overnight. Went out earlier started it and put it in 4x4 and it started puling out front wheels engaged. As soon as I gave it a little gas the front wheels became disengaged and it wouldn't go anywhere. I made several more attempts and no luck. I did the vacuum test where you turn the heater on panel and if there's a vacuum leak somewhere the heater blower will default to defrost. It passed this test so I'm assuming there is no leak anywhere. Why it worked right after I replaced the transfer case motor and again only after I got stuck and it set in the mud overnight?
View 2 Replies
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 Replies
I just got a 99 Ford f150 with the 4.6. I am having problems getting the four wheel drive to engage. I turn the on the dash and the lights come on for four high and for four low. I have a 00 four by four and it works fine, so I know how to work it. In the 99 I can hear the transfer case engaging and everything clicks just fine just like it's going into fourwheel drive, but the front end is not pulling. The front drive shaft is turning but still the front end is not engaged. What the problem may be?
View 4 Replies
How do I get the ac control switch out of the dash? Something must have come loose as I only get cold air or heat to the windshield...
View 13 Replies
I need a front axle tube for a 1999 F-150 4x4, I have tried local parts houses and dealership with no luck. Any information where I might locate one.
View 6 Replies
My buddy has been having a strange problem with his 275,000 mile 2003 F150 2wd. The right side caliper will lock up out of the blue and will not release for anything. We put 3 news calipers on it within a 4 week period thinking that we had a defective one but no change. I am thinking either a bad brake line or, more likely, the front abs block...
View 1 Replies
I have a 2000 F-150 XLT Supercab 5.4 4x4 with the dash shifter. My front axle won't engage when shifting into 4x4. A few months ago the vacuum solenoids were replaced and they sound as though they are functioning properly. The diaphragm isn't moving the lever thing and i can't get the lever to move with a screwdriver either.
I know it has worked the past two weekends. Two weeks ago it was in a significant amount of mud and possibly submerged at times. I power washed everything pretty good immediately afterwords though and it has worked in between then and now. What could be going on?
View 11 Replies
I have a 1999 F150 Supercab, 2wd. I just replaced the front rotors, calipers, and pads. Before I did this, the front right caliper was locking up completely. Now, after the new stuff is installed, the truck pulls very hard to the left when braking. The harder you brake, the harder it pulls left. What should I look at next?
View 2 Replies
Last weekend I was cutting wood and put my 2001 F150 into four wheel drive for the first time in a long time. I did it "just in case". Anyway, now my fuel mileage really took a nosedive. Is it possible one of the hubs did not unlock? If so, how can I test? Common problem?? 215,000 and going strong!!!
View 8 Replies
I'd like to turn off my drl's.....getting new front bulbs and going to install some led's to use as drl's. Up to now, I've only read about using VAG-COM to turn off. I just came across a YouTube demo about turning off drl's by pulling out switch on dash, disconnecting switch from connector and bending down a prong inside the connector. Sounds and looks simple. I haven't seen this method written up on Vortex before....
View 3 Replies
last weekend I was cutting wood and put my 2001 F150 into four wheel drive for the first time in a long time. I did it "just in case". Anyway, now my fuel mileage really took a nosedive. Is it possible one of the hubs did not unlock? If so, how can I test? Common problem?? 215,000 and going strong
View 9 Replies
2001 has no power from fuse 1 to switch. Hazards work, not sure about reverse lights. No gear indicator light on dash. I've changed this switch before, plug and play. Not this time.
View 4 Replies
The switch for turning overdrive off that's located on the auto trans shifter stopped working. I've taken off the column cover to see if the wires have been severed from the tilt wheel, but nothing wrong there. I also checked the fuses, and all is well. Is it possible that the switch is bad at the end of the shifter, or somewhere farther down the column?
View 14 Replies
I thought that my front wheel bearing was bad but I removed it and it seems fine. The issue that I'm having is a continous vibration (noise) in the left front that gets worse with speed.The half shaft makes a noise at the point where the half shaft meets the steering knuckle and when I turn the shaft at the outer splines, the grinding noise is present. My question is, is the entire half shaft supposed to turn, even the outer diameter of it that would enter the steering knuckle, or is the shaft supposed to turn inside of that outer diameter? I hope I was able to explain my problem clearly/
View 6 Replies
I have a 98 F250LD, its a Lariat, so everything electric/auto. Shift on the Fly 4x4, 5.4, 188K, Factory rear air suspension. Typical Minnesota rust. Anyway, I just noticed in the last 75 miles or so, a drive-line vibration. There is nothing until 39 MPH. Then from 39-41 MPH there is a decent vibration. Stops until 50, then from 50 MPH up it is a steady vibration. I have already changed the u-joints in the rear shaft. I have pulled/wiggled on everything else I can think of with no luck of finding of anything loose.
One thing I did notice, is that the front axle is locked in all the time. How long it has been like this: years for all I know... I can flip the switch from 2wd to 4H and 4L. It all seems to work fine, I hear clicking, the 4x4 engages, the proper lights come on/off. The front axle will pull when supposed to. The transfer case seems to be working fine, but the front axle won't disengage. I am hoping this can be fixed cheaply/easily (DIYer), and also hoping this explains my low fuel mileage.
Front axle? Where to look or what to try and fix for the vibration?
View 2 Replies
This is a truck at work, I had my student workers put in a new blinker switch, and when they were done it won't start anymore. The "theft" light is flashing on the dash, so I guess the PATS system thinks it was tampered with. How could you trigger this by changing the blinker switch? Does this have to be reset by a dealer?
View 3 Replies
