Ford F-150 - 1997-2003 :: 2000 XLT - No Start - Two Relays And One Fuse Under The Hood Missing
Jun 16, 2014
Have a problem with starting. Truck had an alarm system that I took off. Reconnected the wires back to factory. Installed a new battery-starter cable. Checked and had no radio and no power windows. Found two relays missing and one fuse under the hood missing. Installed new. Tried again and have all accessories but will do nothing when turning key to start. With key on I can jump across solenoid by starter and it will start. Once started it will not allow me to shift out of park. If I shut truck off and turn key to on position I can shift out of park and into neutral and jump across solenoid and it runs. Once I shift back into park it kills the truck and we start all over again. I've traced wires and fuses and can't find anything. 2000 f150 xlt 4x4 5.4l....
View 3 Replies
Advertisement
I have a 2000 E350 boxtruck with a 5.4 auto. The motor is a new rebuilt with about 4000 mile, coils were replaced with motor, injectors were rebuilt with motor.Today (500 miles from home) the truck died. I was going up a slight hill on an interstate. It will still start, but runs very rough and when I put it in gear and step on the gas it dies.
So I had it towed to a garage. While pushing it into the garage I noticed my gas cap was missing. I know it was on 45 min earlier because I got gas. Did I forget to put in back on? probably.. But I wondering if the missing gas cap could cause the truck to run bad,vary bad?
View 14 Replies
I have a 2000 LS, V6, that won't start, had the battery and alternator checked and are fine, last week i notice when I turn the switch to start up there was a 1 or 2 second delay then it would start, the other day the wife called me at work to tell she she was out and it wouldn't start as I was talikng to her she tried it and it started right up, didn't do it again until this morning, check the fuses and all were ok, it started 2 times then about 30 minutes, nothing, and i mean nothing, the security on the dash doesn't indicate a problem, I turn the switch everything lights ups as it should, everything works(radio...etc.) go to start and nothing but click, sounds like it comes from the fuse/relay box under the hood, starter maybe? relay?
View 3 Replies
I have a 2000 F150 with 4.6l triton 125k miles. i have a bad miss ONLY between 1500 and 2000 rpm. This will happen in any gear and in neutral, but only between those rpm's. seems to happen more constant in warm weather. This miss is so bad it feels like the transmission is going to fall out. but since it does it in neutral i doubt tranny problems. things I've replaced: fuel filter, tranny fluid and filter, crankshaft pos. camshaft pos, TPI, MAF, spark plugs, Ignition coils ( all 8) cleaned throttle body ( found 1 EGR port clogged completely )..
I had a couple codes but nothing constant. Been working on this for about 1 year. Codes p0320 (ignition speed input error) p0262 (injector circuit high cylinder #1). my only question here is...... What would only make this dang engine miss between 1500 and 2000 rpm. motor runs perfect thru all other ranges. idle... high speed.. and even throttling through this bad range is ok.. but when stabilizing between 1500 and 2000 starts jerking and missing like no fuel and no fire. i have put in superchip program couple years ago and it ran fine for about 1 year, then this trouble started... I have put back to stock program but still trouble.
View 2 Replies
Cooler weather has arrived and my 2000 f250 won't start. Wait to start light is coming on, no power passing through the two relays on top of the engine. Are both of these for glowplugs? My 97 only had one. How do I diagnose relays on this truck? If you cross out the two relays truck fires right off so I know the glowplugs themselves are good.
View 7 Replies
I have a 2000 f150 with 5.4 Triton with 165k miles. I did invest in a code reader. It started missing and code P0302 came up along with P0171. Put new coil on #2 and truck ran fine for a few days. Then it started to run rough again. Shaking, Idle rough, no power and CEL came on again. This time code P0171. I changed out fuel filter to no avail. My next step was to start looking for vacuum leaks. As I'm searching, All I am finding is trucks with this problem also get P0174 code. My question is since I am only getting lean on one bank does that pretty much eliminate things like MAF or the famous elbow vacuum leak and make something that only affects one bank like an O2 sensor on CAT more likely?
View 2 Replies
2002 F150 5.4L. Keeps blowing fuse in location #30 which is a 30a fuse for the following:
Passive anti theft transceiver
Cluster
Ignition Coils
Powertrain control module relay
Coil on plugs
Radio noise capacitor
ECC diode
Could this be a grounding spark plug wire?
View 4 Replies
I have a 2002 F-150 xlt 4x4 5.4l V8, 96k miles. been sitting about 3 weeks i went to start it and nothing.. thought ok jump. We tried jumping/charging the battery nothing. then we switched batteries from running car same thing when i turn key just hear a click in dash. battery light remained on even when we swapped out. The theft light was off as well.
View 1 Replies
I've been getting ready to take a camping trip with the, new to me, Superduty and going to rent a trailer. When I bought the truck it had no brake controller and the aux relay box was pretty dusty so don't think it's towed in a while. I got my self a controller and the jumper harness to go form the factory connector to the controller, then went to local parts supply and got two standard auto relays and a 30 amp maxi fuse. I noticed after installing the system the reverse lights stay on after putting the truck in reverse, they don't even go out with the key off.
Did some further testing and found pulling fuse 28 (central Elec) the circuit stay powered up, but only after shifting to reverse the first time. Can only turn off lights so far by pulling the trailer relay at the back of the aux. relay box where the two "towing" relays go, I fairly certain it's the "Trailer back up lamps relay". The power mirrors stay powered up too so the relay control circuit is staying powered but only after the relay is energized. What the issue maybe or where to look for a short? I guess there is the a less obvious possibility too - did ford use some funky special wiring for the relays meaning my standard automotive relays from the parts store are incorrect?
View 1 Replies
New to this site, my problem is on my 2003 4.6L fuel pump not working.My problem is that I am not getting voltage to contacts on pcm and fuel pump relays.
Getting volts to #30 fuse 30amps ok, voltage to pcm diode ok. Voltage on #30 on both relays(pcm & fuel) but I am loosing voltage across coils contacts #85 & #86, these makes hot #30 & #87 to make pump work. Inertia sw ok, Don't know if PCM is bad, ck fuse #2 ok 5 amps.
View 14 Replies
I have a 98 f150 Lariat 4wd Automatic with a 2000 4.6. When i turn the key the only thing that happens is i hear a relay in the fusebox in the dash clicking. I can cross the starter relay on the firewall with a screwdriver and itll start right up. Heres what ive done troubleshooting wise.
1. Checked battery terminals. Fine, it will start with jumping the relay so it seems good with that regard.
2. Tested the relay per the manual. Good.
3.Ohms Tested the white ignition switch box under the dash per manual. Good
4. Voltage tested the Trans Range Sensor per manual. Good.
5. Checked over all fuses, none blown.
6. No theft lights come on.
I figure since it will start jumping the relay that the battery, starter, and starter solenoid are all good. Only thing i cant seem to find is the Starter Interrupt Relay, or any sign of fusible links on the main battery cables. I am really at a loss here i figured one of the components ive tested would be it.
View 14 Replies
I was having intermittent fuel pressure problems. I replaced fuel pump and relay and was still having the problem. A figured out that wiggling the 20 amp fuse would cause the intermittent. Looking at the connections for the fuse, I can see one side was damaged. I figured I could pull the connector out from the back and fix the connector, but when I took the back off (see picture) I have a purple wire (labeled 1) going to one side of the fuse and a multi-connector (labeled 2) from one wire going to the other side. My luck, it's the multi-connector side that is damaged.
It Looks like the multi-connector goes to the Black and yellow wire. Instead of replacing the box, I figured I could just create an inline fuse for the fuel pump with the purple wire and splice it into the Black/yellow wire.
I can't see any problem with this, just looking for a second opinion. And I'm not sure how it would effect the relay. I can't find a fuse panel wiring diagram anywhere.
View 2 Replies
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.
View 5 Replies
I am having trouble with my 2001 F-150. Starting yesterday it would not start. At 1st i thought it wa the battery, so i took it off, charged it, put it back in the truck and still no start. There is a clicking noise coming from a relay in the cabin fuse box, disconnected the battery, removed relay to inspect and everything looks good. After plugging it back in, and connecting the battery, the truck still wont start and there is a clicking sound coming from the dash near the radio. Rhis is my work vehicle!!!
View 3 Replies
So I have recently did a body swap on my 7.3 I rolled. Put a body from another one this one. Before I took the old body off the engine ran fine. Nothing wrong at all.
Now that I have the new body on, I am stuck with a fuel shutoff switch. I read that it is suppose to be pressed down, but when it is pressed down, I turn the key and 4 relays under the hood click rapidly, 2 under the dash, and the drive side blinker blinks? Anyway, when I push it up, and turn the key, all the lights come on normally, wait to start light comes on. It'll crank good, the battery's are good, had them tested and fully charged. Checked ando triple check all battery connections and grounds. Anyway, it'll crank and want to start it fire up for a second and die. The low pressure oil gauge on the dash doesn't go up, but I think I broke the sensor connector for that. The fuel pump doesn't make any noise, the fuel bowl has fuel in it, but does fill up with fuel. So I'm thinking the fuel pump is somehow shorted out, so when I depress the fuel shutoff switch it makes everything go crazy. But even then the fuel pump doesn't make any noise?
View 6 Replies
Need to diagnose this before I start ripping wires:
Truck started blowing the # 8 fuse under the hood tonight (15 amp #8 - trailer tow electronic brake illumination, park lamps, trailer tow park lamp relay coil fuse) which also controls the dash board lights (can't see gauges at night) and the tail light lights (brakes lights work) are out too. Figure I have a short somewhere.
View 14 Replies
In some areas, the internal PTC cabin heaters were missing the relays and didn't work. They mentioned that the relays were in the glove box and that they easily installed them manually. There were no relays in my glove box, but I couldn't be sure if they were installed. So I took a picture of my "relays and fuses box" for someone with experience to examine. Are the PTC heater relays installed in my car?
Full resolution Dropbox link: [URL] .....
View 3 Replies
I bought this truck new, then sold it to my son, now I bought it back from him. it has sat a lot the last three years. replaced egr valve 08-13, fuel filter 12-13. CEL has been on for a while 02 sensor, it had a bad miss in it so had advance auto scan it and it had miss in #3,#5 and I think he said high pressure exhaust gas? he cleard the codes, so on the way home, It started running good.
The next day it started right up and drove it a couple blocks. it sat for 30 min. then wouldn't start. I cranked it for a while. No gas smell? Hooked a timing light up and didn't get no light? I am not sure if you can check to see if its firing this way? What is the firing order? how to check the fuel pressure? when I have removed gas cap it doesn't make any sound from pressure in the tank. Also how to test coil?
View 14 Replies
Here's the deal. Ive got a 2000 f150 4.6 4x4xlt 170000 miles, About 2 ears ago or so the truck would not start on the first try or two. now this only occurred every once and a while. Last winter it became more of a problem. All i had to do was cycle the key a couple times listen for the pump to prime and was good to go. Summer rolls around no problem at all. Fall rolls around and here we go again no prime. cycle the key a couple times good to go. As it gets colder the problem gets worse. No we fast forward to couple a weeks ago, was out in the woods cutting firewood i go to move the truck and it wont start. I have to cycle the key like 30-40 times. Now its doing it like every time i go to mov the truck until yesterday. Now it wont prime at all. Now every time it primed in the past it runs perfect after it starts . the filter has been changed every 12-15000 or every fall, Ive replaces the fuel pump relay to try it no change, tryed the other key no difference. Im leaning towards a pump but ive never heard of one doing this before.
View 6 Replies
My truck is trying to start its self the lights flash and one of the relays makes a loud buzzing sound. I can take the relay out the sound stops but they truck still tries to start/lights flash.
My wife has been saying she's been hearing a clicking as she drives it coming from the drivers side somewhere she thinks under the dash. But at this point nothing happen. And it had not been raining any when this was happening not for a long time.
The first time anything mechanical happen was only the lights came on and stayed on and drained my battery about a week after wife heard the clicking noise. I recharged the battery and chalked it up to my wife maybe bumping the light switch slightly causing them to stay on and not auto on and off. truck ran fine for a couple of weeks then wife drove it again the other day and after she got home she called me at work saying it was making a bad buzzing sound lights were on and its trying to crank, while it was sitting in my driveway with no one in it (sacred her to death).
That day it was raining. Now I had a small drip coming from driverside window inside so I thought maybe went down on my fuse box. So today I tried to get it out but having a hard time getting cables to disconnect so i left it and inspected really well and it does not appear to have been wet at all. Dust on top no water trails or marks same from side bottom and in the fuse holder. So i really don't know whats going on. Maybe still is fuse box?
2000 f150 5.4l 4x4 ......
View 1 Replies
Have 2000 Ford XLT Extended Cab 4x4 with 5.4. It will not start. Put the ignition in on position and can't hear the fuel pump running. Fuse Okay, Relay OK. Does this year have A Fuel Pump Driver Module? If so, where is it located? I know where they are located on 2004 and up but not mine. If I have to change out Fuel pump, is it easier to pull the tank or the Bed?
View 6 Replies
