Ford F-150 - 1997-2003 :: 2000 Truck Started Missing And Code P0302 Came Up Along With P0171
Nov 8, 2015
I have a 2000 f150 with 5.4 Triton with 165k miles. I did invest in a code reader. It started missing and code P0302 came up along with P0171. Put new coil on #2 and truck ran fine for a few days. Then it started to run rough again. Shaking, Idle rough, no power and CEL came on again. This time code P0171. I changed out fuel filter to no avail. My next step was to start looking for vacuum leaks. As I'm searching, All I am finding is trucks with this problem also get P0174 code. My question is since I am only getting lean on one bank does that pretty much eliminate things like MAF or the famous elbow vacuum leak and make something that only affects one bank like an O2 sensor on CAT more likely?
View 2 Replies
Advertisement
I've got a 97 f150 4.6 that has randomly started missing over the last month. It has started to get more frequent and codes are showing a misfire on both cylinder 1 and 8. Both of these cylinders run off the same coil pack. I'm thinking its the coil? The plugs and wires, motocraft, have about 3k on them and the truck runs great otherwise. I just don't know how common a coil would cause this or if they would act intermittent like this.
View 5 Replies
I have a 1998 F150 5.4L 4WD with 192k mi on it. Recently ( suddenly ) the vehicle began shuttering pretty alerting under light load at 35 - 45mph. The engine idle was intermittently smooth then rough. I quickly drove the truck home and ran a Trouble Code check with my Autoxray EZ-scan 4000 and found the two trouble codes P0302 and P0171. I have checked for vacuum hose cracks and found none.
Replaced the fuel filter, PCV valve, and cleaned the MAF sensor ( dirty ).
Right after cleaning the MAF sensor the idle remained smooth - but stumbling immediately when put in drive. Driving at 35-45mph still exhibits intermittent shuttering and occasional very short bursts of what feel like complete engine shut-down. This all is evident under light to moderate load .
At this point what would you recommend ? Replacing the O2 sensor bank #1 ? Or is there a possibility maybe the EGR valve is faulty - or another vacuum valve somewhere ? Intake manifold leak ?
The severe stumbling and very short complete engine shut downs would indicate that maybe the computer is failing or it's a fuel delivery issue? What rational steps to take next ?
View 14 Replies
My daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
View 6 Replies
I've got a 2000 f150 with a 5.4 and 135,000 miles. The other day it was driving fine then i stopped and got gas and after that it was boggy and running rough so i thought bad gas but i ran through that gas and got more at a different store. The cel came on i got it checked it was misfire cylinder 1 so i put new cop, spark plug, and injector. Unhooked the battery and then the light came back on so i ran the code and now im getting a p0171. I checked the pcv and sprayed around the intake and vacuum lines. I also checked the pcv hose and elbow in the back and i found nothing its a fairly new hose. So, it does run rough it shutters a lot.
View 2 Replies
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 Replies
I have a 2000 Ls 3.9 V8 125,000 miles that started idling rough.I checked for codes and got p0171 (bank 1 lean), p0175 (bank 2 rich) and p0307(cylinder 7 misfire). I swapped cop and sparkplug from cylinder 7 to cylinder 5 and erased the codes.I ran the engine for a while and rechecked the codes to see if the misfire followed the cop and plug. They did not. I still get p0171,p0175 and p0307 (cylinder 7 misfire).
View 7 Replies
I have a 2000 f150 4x2 5.4 168k... Check engine came on,started shaking, weather was really cold. RPM would be a little high then low then back up. Especially when I turned on heater. Felt like truck would die but never does nor does it have issue starting.
So far, I have replaced two oxygen sensors inside engine,all coils, spark plugs, fuel filter, had injectors cleaned, intake cleaned. Truck runs better but, light came on a day later again. I can feel the tiniest of shaking going on and, cold mornings still make RPMS a little unstable. I was driving truck on highway at about 60 mph when a slight tug was felt and Truck check engine came on. I feel truck heavy, once it warms up completely, a little lighter.
Codes came up at auto zone as P1151
But I'm running out of options and frankly, money to fix this truck.
Checked the MAF and looked okay.
I'm with minimal skills.
View 13 Replies
I have a 2003 F150 4.2 with 155000 miles. What may be causing this?
View 6 Replies
The "service engine soon" light on my 2003 F150 Supercrew 4.6L (225k miles) just came on. The code it's throwing is P0171.
View 3 Replies
1999 xlt with 5.4 lt p0171 only. it started with what felt like a misfire or hesitation and rough idle. Extremely rough at 40-45 mph. but with no misfire codes just p0171 so all 8 coils and plugs and sparks replaced twice in one month. and still same code tested fuel pump pressure 28 psi.... removed clogged cats, still same code... new pcv valve and elbow.... checked for air leaks around intake and intake manifold and nothing.... cleaned mass air flow sensor...I can unplug any coil on bank 1 and it wont make a difference. But if I unplug any bank 2 coils and engine makes a difference.
View 2 Replies
I have a 2000 f150 with a 5.4 past few months it has been throwing a p1151 code meaning it is coming up lean on the driver side. I just changed the plugs and it didn't work, neither did changing the fuel and air filters. cant find any vacuum or exhaust leaks. Replaced a bad injector along with the spark plugs and its still coming up lean.
The truck also seems to bog down at about 50-60 mph if i let off the gas and coast it will drop about 300 rpms. It has me confused and annoyed, i have true duals with glass packs could that be causing it?
View 4 Replies
I am still battling a p0171 code on my 2000 f150 5.4. I checked the fuel pressure at idle it sits at 31. I remove the vacuum line off the regulator it goes to 41. When i give it throttle when in gear it will maintain at 30. And when I shut the vehicle off completely it will maintain 38. Just looking to see if this is correct numbers. I was trying to determine a weak fuel pump.
View 9 Replies
97 F150 4.6 200xxx on recent rebuild. My truck is throwing P0171 & P0174.
I think I tracked it down to leaky IAC and EGR gasket. I sprayed both with carb cleaner and the RPM's dropped.
My question is, wouldn't the RPM's rise instead of drop? I was under the impression that they would go up if the gaskets were leaking. Or did I use the wrong spray?
View 4 Replies
97 F150 4.6 Vin 6, 5-Speed Trans, 200,000mi, Rebuilt recently. I was on my way to get my truck smogged, but she threw a code, P0171. I read somewhere to clean the throttle body elbow, which I did (needed to do it anyway). After I had everything put back together, I start her, and it's rough and immediately dies. If I keep the RPM's at about 1.5k for a minute, then let off, the truck will run fine for about 30-45 seconds, then die again. I just replaced my IAC and the problem persists.
View 8 Replies
I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.
2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.
I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.
View 2 Replies
P0306 (ok #6 missfire) with P0171 & P0174 --- Do I chase electrical or fuel or both. Afraid to assume anything but probably would normally address the misfire electrical first.... Don't want to go down that 'primrose path' if others have been there first!
View 4 Replies
My 4.2 liter F150 suddenly started missing under load. A little background: It is a late 2003 and has 75k miles. It has been in my family since new, and I have had it for the last 4 years. This truck is as stock as they come, and has been well maintained.
On my way to work yesterday, it began missing. Not bad at first, but got worse. It misses while under load and under acceleration. The "check engine light" never came on. I have not put fuel in in several days, and it ran fine until now, so I doubt it is bad fuel. I started the engine after dark and looked for arcing. None visible, and I even sprayed the wires with a mist of water. I pulled the plugs and they all look normal. The gaps were all way too large, so I regapped the plugs to .054". I pulled the coil pack and it checks within range with my VOM. Can the coil pack be the problem even though it checks out on the bench? Can the large plug gaps have contributed to a coil pack failure?
Where to start. I HATE just throwing parts at this thing, and I don't like wasting money... If I let one of the auto parts stores run a scan, will it show a code even though I have no check engine light? I used to think of myself as a pretty good diagnostician, but then again, when I used to spend a lot of time under the hood, those cars had points, condensers and carburetors...
View 4 Replies
It's been a long time since I have posted here mainly because my truck was wearing a bow tie for awhile. But my wife was nice enough to tell me the Bow Tie wearing truck was making a funny noise on New Years Day (seems a small drum corps took up residence in the oil pan). So anyhow now I am back in a real truck . My new to me 1998 F150 5.4 Liter ran fine until yesterday. It started idling rough and almost stalling at red lights. about halfway home the CEL light came on and is throwing a P0171 code.
So far I have checked for vacuum leaks including all the elbows on the PCV system' tried the spray test with a can of flammable break fluid and a can of starting fluid (man I love the smell of that stuff) could not find a leak. Cleaned the MAF sensor and the K&N air filter (not a fan of these) IAC seems to be working. Only thing I know that is leaking for sure is the driver side exhaust after the cat. But that is the wrong bank if I am correct on which bank is which.
So why only one bank running lean and why does it act like it is only firing on 4 cylinders?
View 14 Replies
I have a 2000 F150 with 4.6l triton 125k miles. i have a bad miss ONLY between 1500 and 2000 rpm. This will happen in any gear and in neutral, but only between those rpm's. seems to happen more constant in warm weather. This miss is so bad it feels like the transmission is going to fall out. but since it does it in neutral i doubt tranny problems. things I've replaced: fuel filter, tranny fluid and filter, crankshaft pos. camshaft pos, TPI, MAF, spark plugs, Ignition coils ( all 8) cleaned throttle body ( found 1 EGR port clogged completely )..
I had a couple codes but nothing constant. Been working on this for about 1 year. Codes p0320 (ignition speed input error) p0262 (injector circuit high cylinder #1). my only question here is...... What would only make this dang engine miss between 1500 and 2000 rpm. motor runs perfect thru all other ranges. idle... high speed.. and even throttling through this bad range is ok.. but when stabilizing between 1500 and 2000 starts jerking and missing like no fuel and no fire. i have put in superchip program couple years ago and it ran fine for about 1 year, then this trouble started... I have put back to stock program but still trouble.
View 2 Replies
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 Replies
