Ford F-150 - 1997-2003 :: 2000 - Power Steering Gone Out
Mar 3, 2016
Purchased new 2000 F150 5.4 automatic 2wd now the power steering has gone out. I read all the things about the intermediate shaft seizing up so sprayed and prayed until I finally broke down and ordered a new one. Well I just pulled off the original with over 250,000 miles it seems like new. The tiny u-joints are very free moving (not sloppy at all) and the sliding shaft works fine.
I'm starting to worry that the power steering pump is shot although it was not squealing or groaning. I do have some tie rod and ball joint squeaks, could that be it? I'm really frustrated thinking it was going to be a simple intermediate shaft replacement now I've got a brand new one and the same problem. The lower power steering hose was pretty grimy but I figured that was all of the PBlaster I'd been spraying on it.
I'm going to jack it up and try moving the wheels back and forth to see if it is binding anywhere. Was reading about a high pressure switch but where that even is or if the 2000 has it.
View 7 Replies
Advertisement
I am replacing the high pressure power steering line on my 2000 Lightning and have a question about the fitting that goes into the steering gear. The new hose came with a black rubber o-ring that the instructions seem to indicate goes on the end of the steering gear fitting. The problem is that I did not see any o-ring on the original hose end or in the steering gear itself and the hose did not leak there (it was leaking on the pump fitting). Should there be an o-ring at the end of the fitting or does the fitting go on without it and uses a metal to metal seal? If replace this hose, did you use the o-ring or leave it out? Does it go on like this? Or like this?
View 4 Replies
I have a 2000 Ford F150 XLT 4X2 that has a "clunking/squeaking" noise in the steering wheel, intermittent happens driving straight down the road, hitting bumps, breaking. It is very annoying! changed out lower ball joints tightened wheel bearings, greased idler/pitman arm thinking that was the problem and it became worse. Had someone look at it and stated that the steering shaft was welded?!?! Why would the steering shaft be welded what am I looking at in replacing it (cost for parts and labor time) and are there any other additional parts that will have to be replaced as well?
View 1 Replies
Purchased 2000 F150 (224000 miles) about a year go cheap for knock around truck. Only gets driven about twice week (20 miles most). Has been running great until recently. Got in the other day went about a mile and notice really strong vibration in steering wheel and dash. First thought about something to do with alignment etc. After a little experimentation realized it was the motor. When you get to around 40 mph and try to hold the speed constant it starts shaking (I believe the motor is missing). If you mash the gas and accelerate it stops. As soon as you try to hold constant speed again it starts again. I can run it up to say 45 and let off the gas and the shaking stops. Once it was driven like this for about 5 miles or so, when I come to stop sign it idles rough. If it is put in neutral runs smoother. Could the fuel filter be clogging up? I did try some additive to see if it would clean it out, no luck. Now the check engine soon lite came on. Fuel Filter, Plugs?
View 5 Replies
I have a 99 5.4L V8 Triton engine. The power steering is not working. Need a full power steering diagram including components and hoses/lines? I have attached a picture of a broken line which I think might be for the power steering but I'm not sure. What this (?) line is in the attached picture or have a diagram?
View 3 Replies
Just curious what type of power steering fluid should be used in our trucks. What works best?
View 2 Replies
I have 2002 F150 5.4L gas 4X4 Lariat FX4. Last winter when it got to -30C here in Manitoba one of the lines near the power steering cooler began to leak. I had just bought this truck and upon investigating found that the original line had been replaced and reattached with hose clamps. I had this "farmer fix" redone but then this winter when it hit -30C it blew apart. Obviously something happened to this line before I got it, so I am curious if there is an issue with these power steering cooler lines when it gets really cold. Should I just get factory lines installed and hope for the best?
View 3 Replies
Across Internet is lot of examples of using pump, usually drill pump or vacuum. It seam to me that drill pump would work good for that job. Pump that attach to battery have limited amount of power and vacuum pump is manual. Look like a excellent device for transmission fluid change. Clearly no drain screw at pan. I do not think I'm fan of disconnecting return line and live empty tranny.
For example here : [URL] .....
View 6 Replies
I started noticing a problem with my steering on my 2000 Excursion, a couple of days ago. when I make left or right turn, the wheels seem to want to continue in the direction of the turn even as I am straightening up the steering wheel. I have to over compensate on the steering wheel to straighten the wheels it seems. It does it when I make a left or right turn, but seems to be worse when turning left. Also I noticed that if I'm driving on pavement that has ruts from heavy traffic, the front end seems to pull to one side then the other.
I've had the truck for 7 years and this is the first time this has happened to it. Is it an alignment problem or is there something else that I need to consider? I jacked it up today to check the tie rods and drag link, everything seemed ok
View 6 Replies
I just bought a 99 f150. Its in great shape only 65000 on it but there is a hissing swooshing sound when turning the wheel... not really any brake sounds. The truck has been maintained and I dont see any leeks in the ps system hoses. I didn't know anything about the atf fluid in the truck... and I haven't added either ps or atf fluid to it. I'm wondering if that is maybe something the dealer i bought it from did. or maybe one of the shops the previous owner did. Would ps fluid cause these kinds of sounds? Do I need a flush of the system.. How to do that.
View 14 Replies
I have a 2000 f150, the overdrive light flashes on the swifter, the motor has no power and sputters unless I put it in second gear. It won't shift gears in drive.
View 1 Replies
I bought this truck an it ran good then one day it started knocking really bad so i replaced the crank shaft an bearings. Put everything back together started the truck an it ran like crap an i just happened to check the oil an it is milky. All the water in y radiator is now in the motor oil an truck has no power...
View 2 Replies
Where to find a nice, simple step by step instructional for tightening power steering belts for a 2003 hyundai accent?
View 4 Replies
I have an 03 Accent. The all metal high pressure power steering line had a leak. So I bought a new one for around 70 dollars from Hyundai. This part has a curved shape and fits around the radiator. The old one was difficult to get off, but the new one is proving impossible to get on. I cant get it into place.
View 2 Replies
I have a 2000 F150 with 4.6l triton 125k miles. i have a bad miss ONLY between 1500 and 2000 rpm. This will happen in any gear and in neutral, but only between those rpm's. seems to happen more constant in warm weather. This miss is so bad it feels like the transmission is going to fall out. but since it does it in neutral i doubt tranny problems. things I've replaced: fuel filter, tranny fluid and filter, crankshaft pos. camshaft pos, TPI, MAF, spark plugs, Ignition coils ( all 8) cleaned throttle body ( found 1 EGR port clogged completely )..
I had a couple codes but nothing constant. Been working on this for about 1 year. Codes p0320 (ignition speed input error) p0262 (injector circuit high cylinder #1). my only question here is...... What would only make this dang engine miss between 1500 and 2000 rpm. motor runs perfect thru all other ranges. idle... high speed.. and even throttling through this bad range is ok.. but when stabilizing between 1500 and 2000 starts jerking and missing like no fuel and no fire. i have put in superchip program couple years ago and it ran fine for about 1 year, then this trouble started... I have put back to stock program but still trouble.
View 2 Replies
I noticed after the crash the steering wheel is moved forward and gear shift is up against dash. asked around and one person said they made collapsable steering wheels to impact. i have never heard of such a thing.
View 5 Replies
Recently noticed when driving, I'll hear and feel a slight clicking noise coming from my steering column. I can be going straight or turning. it is intermittent. I've look underneath and nothing seems obvious. when the truck is in park, I've tried to manhandle the steering wheel, the steering wheel is solid. the truck is a 1998 f150xl v6.
View 1 Replies
I want to replace my steering wheel. Will this puller work for that job?
View 5 Replies
I have a 97 F150 that I just got a few weeks ago. I was driving home Wed. night when the 4x4 low range light would come on and off intermittently I had it in 2h the whole time. I went online and couldn't really find anything on it. So I get up to go to work on Thursday and the truck wouldn't even turn over. The battery was dead. I have put in a new one but now after turning the truck off I hear a clicking sound coming from the steering wheel. What this may be?
View 3 Replies
My 02 F150 4x4 at times gets a shake through the steering when hitting road cracks, pothole fills, etc. Would installing a steering damper system work or am I missing something to check in the front end. Ball joints are good, all steering linkage good, new shocks all around, control arm bushings look good and don't seem to shift when prying with a bar. Also changed all sway bar bushings and links. Maybe the control arms just have to be changed with 103,000 miles on it even if they appear OK? What about using an aftermarket steering damper on a stock F150? My long gone 82 GMC 4x4 had one from factory but it was also a solid axle setup.
View 4 Replies
I just recently picked up a 2001 F-150 4x4 super crew. The steering column is wobbling a little when I hit bumps. I accessed the column and there are two white plastic "bushings" that hold the casted portion of the column tight against the studs with the star ends. This is above where the reinforcement bracket is bolted on. One of them is worn and won't tighten down to hold the column tight. What these are called so I can't find them to order them, I used a large washer for the time being but would really like to replace with new ones.
View 1 Replies
