Ford F-150 - 1997-2003 :: 2000 - ECM Pinout Diagram?
Nov 23, 2012
Looking for a diagram for the ecm pinouts for a 2000 5.4 4x4 f150? Im mostly trying to find the TCC for the tranny.
View 1 RepliesLooking for a diagram for the ecm pinouts for a 2000 5.4 4x4 f150? Im mostly trying to find the TCC for the tranny.
View 1 RepliesI am trying to add a keyless entry to the already equip, power door locks but am having problems figuring the wiring schematic
View 8 RepliesI just bought a 2000 Excursion limited v10 4x4. I'm going camping this weekend so trying to install my brake controller. I found the plug but noticed these wires dangling. I can't see the back of the harness. I'm afraid the PO may have cut them to install a universal harness. How to recognize them? I don't want to buy a ford specific harness if the wiring has been cut.
View 3 RepliesI just bought an 01 F150 and previous owner didn't have the manual.
Need a copy of the fuse box diagram for this truck?
I've been surfing the net, and can't find what looks like the right one.
Got myself a brand new old truck. No radio and all the wires had been cut. I just printed of a wiring diagram from web and went to work I am now on my second one and it has the same colors for two different speakers!! The first one was completely wrong. Looking for a good wiring diagram for a 97 f250 super cab.
View 1 RepliesAnyway, I'm gimped in my left shoulder for a while and I'm trying to do what i can with my 03 F150 Supercrew /4bt Cummins conversion. I am using a Dodge 47rh tranny and need to know the wiring for the 4R70W so I can hook up my 12 + ignition wire, back-up lights and neutral safety switch. I'd like to build my wiring harness.
View 6 RepliesI have a 1999 Ford F-150 4X4 w/4.6L V8 W code, I recently lost all brakes. The primary line from Master Cylinder to ABS Pump rusted out completely. Replaced them but the other lines from ABS Pump to wheels are looking real bad. So I need to replace them, however I have no idea what the routing system looks like. Looking for a 97-03 F-150 Brake Line Diagram? I live at the jersey shore... so yeah rust is extremely common.... unfortunately.Also, where to get line assemblies?
View 7 RepliesI have a 99 5.4L V8 Triton engine. The power steering is not working. Need a full power steering diagram including components and hoses/lines? I have attached a picture of a broken line which I think might be for the power steering but I'm not sure. What this (?) line is in the attached picture or have a diagram?
View 3 RepliesLooking for diagrams for where the fuel filter is, the coils are in the engine compartment, and a steering wheel diagram because mine wobbles. I did attempt to look for one in a hayes when I was at Pep Boys a bit ago and didn't see one. 1998 F150 4.6L v8 w/auto trans 4wd 3dr...
View 6 RepliesI am working on my son's 1997 F-150, 2 wheel drive, 4/6L truck. He was driving it when the gauges and the tach stopped working. I replaced the cluster and it still blows the fuses. The five amp fuse that is specifically for the cluster doesn't blow. It is a twenty five amp fuse that also power the overdrive circuit, etc.
After replacing the gauge cluster I installed a new fuse and the overdrive button on the shifter started smoking. Where I could get a wiring diagram of this circuit so I can see how it is wired.
I need a wiring diagram for my 2000 F-350 power mirrors also to go along with the power window schematics that I posted before.
View 8 RepliesI have a 2000 F150 with 4.6l triton 125k miles. i have a bad miss ONLY between 1500 and 2000 rpm. This will happen in any gear and in neutral, but only between those rpm's. seems to happen more constant in warm weather. This miss is so bad it feels like the transmission is going to fall out. but since it does it in neutral i doubt tranny problems. things I've replaced: fuel filter, tranny fluid and filter, crankshaft pos. camshaft pos, TPI, MAF, spark plugs, Ignition coils ( all 8) cleaned throttle body ( found 1 EGR port clogged completely )..
I had a couple codes but nothing constant. Been working on this for about 1 year. Codes p0320 (ignition speed input error) p0262 (injector circuit high cylinder #1). my only question here is...... What would only make this dang engine miss between 1500 and 2000 rpm. motor runs perfect thru all other ranges. idle... high speed.. and even throttling through this bad range is ok.. but when stabilizing between 1500 and 2000 starts jerking and missing like no fuel and no fire. i have put in superchip program couple years ago and it ran fine for about 1 year, then this trouble started... I have put back to stock program but still trouble.
2000 Ford Expedition, XLT, 4WD, V8, 5.4 Liter. Had heater core bypassed, changed, am re-assembling, but need diagram for where all hoses connect on block, etc.
View 1 RepliesLooking for a diagram of the steering column? I am looking to see what is behind the ign tumbler that sends power to the ign switch module. I believe a problem might be there . this is for a 2000 x limited 7.3.
View 1 RepliesI have a 97 ranger 2.3L (manual transmission) and want to change the cluster to one with a tach... I have a 2000 cluster but I would like to compare the actual wiring between the two (1997/2000)... I have looked in the Ranger technical area of these forums and also did a search for "dash cluster wiring" and found no info...
View 4 RepliesLooking for a link to the fuel pump wiring for a 2000 V10 Ex? I'm trying to pinpoint my no start issue and want to make sure I don't miss anything. I think it goes from 20 amp fuse under hood to inertia switch to relay under hood to pump? 20 amp fuse has power but at the inertia switch I have no voltage, just approx 35 ohms resistance to ground on both outside wires. Does the inertia switch close a ground or should it have voltage?
View 10 RepliesLooking for a diagram that breaks down the front axle components of a 1997 mercury mountaineer? I believe my drivers side ball joint is shot because it makes a thumping sound whenever it goes down the road and the wheel has a lot of play in it.
View 2 RepliesHaving a problem finding the right belt diagrams for a 2000 F53 stripped chassis in a motor home and the dealer has been no assistance even after spending a bunch on parts...
View 4 RepliesMy wife's 2011 Nissan Altima 2.5S threw a Check Engine Light. Runs fine, but we took it to Meineke for a free diagnostic scan. Problem: they said they couldn't get the diagnostic unit to talk to the car because the diagnostic interface pinout wasn't getting power through the #16 pin. They checked the fuses, but didn't go any further for diagnoses for why it would be doing that.
View 2 RepliesI am in need of a wiring diagram for a 00 ex with factory auto dimming rear view mirror. It only has 3 wires and I think I have them figured out but would like to make sure before making a pigtail to install a mirror I have that has 6 wires.
View 7 RepliesI have a 2000 F-150 XL with a 4.2 V-6, a 5 speed manual transmission and manual shift on the fly transfer case. The 4WD went out over a year ago. When it went out, I was driving at 65 MPH and heard what sounded like rapid relay chatter for several seconds (10 to 15 seconds) and it stopped. The sound seemed like it was coming from the dashboard area where the GEM is located, but may have been from the solenoids mounted on the engine compartment firewall. Actually could have been from both. When the 4WD tried to engage while driving at 65 MPH, the dash lights were flashing on and off and it sounded like the front differential was trying to engage. Of course I slowed down while this occurred to avoid damaging the truck should it succeeded to engage the front differential.
I have a Haynes manual but the wiring diagrams are some what ambiguous as my truck is not as common as those having ESOF. Even researching online I am not certain if the info pertains to my truck. The only diagram I found to be accurate is the vacuum control diagram. I believe I have either a wiring problem or the GEM is bad. When troubleshooting I like to isolate at the middle points to quickly eliminate one side or another when looking at a diagram/schematic.
Ford had a well-noted problem with the two solenoids that control the 4WD actuator and are mounted on the engine compartment firewall. So I started here, as this is a good halfway point and high failure area.Well, the solenoid power connectors had 12 volts on both connector pins (if I remember correctly as it was a year ago when I did some troubleshooting)regardless of transfer case shift position (2wd, 4wd high or low). I was able to manipulate the solenoids and verified they were operating, as I could feel and here the solenoids click when grounding the control side of the pin on each solenoid. I did check fuse 23 prior to checking the solenoids. Since 12 volts was present at the solenoids, it indicated power was getting to them.
So another common problem is the transfer case 4WDsensor. I removed, cleaned, and verified operation of the sensor. Reinstalled and check sensor state with transfer case in all 3 positions and it was working correctly. Also I have no 4WD indication on the dashboard when 4WD high or low is selected. Fuse 6 is good.
My main issue is not having confidence with the wiring diagrams I have found online. I am not sure if my truck has a MSOF relayor the transfer case 4WD sensor signal goes directly to the GEM.
I need to check:
1. Wiring from transfer case 4WD sensor to either GEM or MSOF relay, if there is a relay, will check it along with wiring to GEM,but don't believe it exists for my truck. (I need the wiring diagram to do this)
2. If the transfer case 4WD sensor output is getting to the GEM module, I would think the GEM module is bad. If possible, I would like to check the GEM module outputs to the solenoids, but since the GEM is buried behind the fuse panel, it probably is not feasible.
I plan to call the Ford service department in my area to determine what GEM I have and will buy a GEM online. Replacing the GEM does not look fun, so I have avoided it but wanted to be sure it was the problem.
So I want to know if I am tracking correctly and if there is anything else I should check, and would like the correct wiring diagram as indicated in item 1.