Ford F-150 - 1997-2003 :: 2000 - Bad Starter Solenoid Relay?
Jan 8, 2014
My truck has started fine every time I've turned the key except for last night after work. I got in had all the lights on the dash and dome lights. I turned the key and nothing. Not even a click. Hooked it up to a company truck and it fired right up and ran fine. Drove home shut off and then started it a little later and it started fine. Then this morning it wouldn't start. I hooked up the jump pack and still nothing. I drove my fusion to work and when I got home I went out and it fired right up like nothing happened. Does the work sometimes not work other times sound like the solenoid on the firewall? 2000 4x4 4.6 auto 253k miles
View 4 Replies
Advertisement
I am having some weird issues with my 2000 F150. When I turn the key all the dash lights go out and no start. Ran 2 wires from the solenoid to a switch and it will eventually start. The starter will start real slow almost like the battery is almost dead and then speeds up more and more till it eventually starts. After it starts the theft light stays on the whole time. At this point I have no clue what is going on.
View 1 Replies
I'm putting in a remote starter keyless entry in my 2000 f150 I have all the wires figured out except for the remote start part. Where the wires listed in the photo go? I do have the module required.....
View 3 Replies
Yr 2000 F-150 with V6 . Only 68K miles. 3 weeks ago went into fast food for lunch and then truck would not start. The starter would spin it over real well and plenty of gas etc etc. I came back the next day with a tow truck to take it to the dealer and it cranked and ran perfectly for 3 weeks till yesterday. Same thing. Will not start in parking lot of grocery store.
I only have one key and someone suggested that it could be the chip in the key or the theft system acting up. I only have one key from when I bought the truck 7 years ago used. Someone else said when the anti theft system is screwing up, the motor will be totally dead and starter will not work.
This time I am again planning to tow to the dealer and I fear a huge bill for something that is actually very tiny at fault since the truck runs perfectly well and then mysteriously will not start. This is the 2nd time in 3 weeks I have been stranded. I pulled all the fuses and reinserted. I checked all spark wires and they are in good shape and tight. What could it be that all of a sudden causes the engine to not start up and run intermittently ?
It is something I can do myself and I am pretty capable. I replaced in the last year water pump, power steering pump, ball joints and alternator. So what is not getting..... fuel or spark? The only two things we need for to run ... right ?
View 9 Replies
Any pic or wiring diagram of the starter relay that is mounted to the fender. I'm trying to start the truck finally but it's just cranking and I think I might have mixed up the wiring. Is there supposed to be a constant hot at the glow plug relay when the ignition is off?
View 14 Replies
Upon trying to start my 2003 f250, it keeps blowing the 15A "Transmission Range Sensor then to Starter Relay Coil" fuse. Initially the truck would still start if i did not use the aftermarket Viper keyless start. however, now it doesn't start at all and keeps blowing fuses. I contacted the guy that installed the alarm thinking it might be something on his end. He walked me through reconnecting the factory starter wires which would isolate the issue if it was something on his end. it's still blowing fuses. battery terminals are good and clean.
View 3 Replies
Found out the hard way that the 4wd does not work on this new stupid truck. I've been troubleshooting the solenoids and confirmed that the 2wd solenoid gets grounded and will read ~12V when switched to 4wd; however, the 2wd solenoid always remains grounded and will always read 12V across the plug no matter if it's in 2wd,4hi,4lo. What would cause this? It seems that I would have vacuum going to the front differential from both the 2wd and 4wd solenoids at the same time, thus not allowing it to go into 4wd. BTW, this is on a '98, 4.6, turn dial 4wd
View 14 Replies
I have 97 4x4 f-150 V6 4.2 litre that in 2wd tries to go into 4wd causing a grinding then a thump. When I put the truck into 4wd there is no grinding or thumping.
I believe one of the vacuum solenoids could be bad. Just was wondering which one would cause it to want to go into 4wd while in 2wd. The left most solenoid looking under the hood is the 4wd and the other with the pink vacuum is the 2wd.
I have no vacuum from the solenoids but from the lines going into them.
View 14 Replies
1997 f150 electronic 4wd not working, lights on dash not working(they light up on start up) replaced transfer case motor still not working, checked all fuses, Do not feel or hear clicks on vacuum solenoid, Top vacuum lines on both have vacuum. Where do I go from here? What do I check next....
View 9 Replies
I have 2003 Saturn Ion that will not start. I did test on the starter and battery and everything work fine. When I turn the key to start, the starter relay clicks alright but there is no power going through the starter trigger wire to engage the starter; I have checked the starter trigger wire, all the fuses, and all the relays, but there is no power in the trigger wire. Why there is no power in the starter trigger wire when the key is turned to start to engage the starter so that the car will start.
View 10 Replies
Code P7081
Do I have to drop the valve body to get to the shift solenoid? Is there only one solenoid? Anything special or tricky I should know about?
View 14 Replies
On my 97, just had a new engine installed. Suddenly the Lo presser AC switch died. Now the Start Solenoid (I think) just clicks sometimes. Is this Solenoid on the Firewall the Start Solenoid?
View 6 Replies
I have a 99 f150 and it won't shift out of park. The taillights work and I tried to turn the key forward and move shifter to neutral but it didn't work. Is it the switch on the brake pedal or the interlock solenoid by the shifter?
View 12 Replies
I just replaced my starter solenoid and I'm getting nothing. When 12 volts are applied directly from the battery to the solenoid, the engine wants to turn (granted my batteries are weak) however when I turn the key to start, after waiting for the "wait to start" light to go off and hearing the glow plug click, I turn the key and I get absolutely nothing. No click, nothing. Is there a possibility my ignition is bad?
Would the "wait to start" and glow plug keep working if this were true? Electrical is not exactly my forte'. Before I replaced the solenoid, the bad one had a broken post but the truck would still start most of the time, and when it wouldn't I just connected the two large posts on the solenoid with channel locks or pliers or whatever was handy. I put the new one in exactly the same way the old one came out. I only undid one bolt and set of wires at a time so I wouldn't screw the order up, so I'm at a loss.
View 5 Replies
Yesterday after work, i got in my truck and it started right up, no problem. my stereo has been giving me some fits the past few days, looks like everything is on but no sound, and was thinking it might be a fuse so i proceeded to shut off my truck and take a quick look at the fuse box. didn't find anything quickly fuse wise, so i got back in the truck to go home and turned the key and nothing. no whine from the starter, no click click click like a dead battery, but i do here a single click from the relay switch as i left the case off to do a more thorough investigation on the stereo when i got home. anyway.. here is all i have ran through.
1. Made sure the battery is good, even tried jumping it for good measure..took cables off and made sure they had clean connections.
2. Switched out the relay, and fuses related to the starter in fuse box.
3. Put the truck in Neutral, thinking safety switch.. wiggled it around while trying to start it as well
4. Crawled under the truck, took a screw driver and bypassed the switch all together to make sure it wasn't the starter, starter kicked in like it was new, but no truck start. (key was in the on position)
5. Checked the solenoid post with a test light to see if it had power on key turn, nothing.
6. Checked the fuse box and surrounding wires to make sure i didn't bump anything when taking off the cover..
From all of this it sounds like some safety switch that isn't giving power, otherwise i would have thought the truck would have started when i bypassed the switch on the solenoid. Just seems very odd the timing of it and i have not had any previous issues like this.. just out of the blue, literally less than 5 minutes from starting the truck without issue.
View 6 Replies
Ok so I was looking at my blend door actuator motor to see if it was working. Just took off the bottom vent cover, turned key on and moved the air mixture to see if the motor worked. (it didn't) Then I went to start the truck and all I get is the solenoid on the firewall click each time I turn the key. I put a meter on the opposite side of solenoid and I see 12v across the solenoid. I can't image i did anything while playing around by the blend door actuator motor. I guess I'm looking for confirmation that the next logical step is starter and starter solenoid. Is there anything else I could be missing? is there anything else in that circuit between the solenoid on the firewall and the starter? I also cleaned the battery terminals and the terminals down on the starter solenoid. I also tapped the starter a bunch and put a charger on battery and tried jumping the truck too. Everything else works.
View 10 Replies
My starter solenoid keeps dying. I can't use a retail chain part. They burn up in a day. Always Motorcraft and it only lasts a year or so.
Any way to test this thing to see why it burns out prematurely?
View 9 Replies
I had a bad starter solenoid on the fender in my truck I swapped it out and then my starter went so I swapped it now it is not disengaging the starter If I turn the key to the run position it starts cranking and fires right up before I an let the glow plugs cycle or anything and it won't disengage the starter I turn off the truck and the starter is spinning loud for a couple seconds till it stops no matter if it just start the truck or start it and run it for a couple minutes then shut it off. 99 7.3L ....
View 6 Replies
I have a 97 F-150 that the A/C went from blowing cold to hot instantly. I have done the following;
1. Checked fuse. Was good.
2. Checked Low Pressure connection.
On this, I jumpered the connector and could not get the clutch to engage. I also checked to make sure I had 12v from that point, which I did.
3. Checked the power to the clutch assembly. Got nothing. I also put 12v directly to the clutch and it poped in just fine.
Based on all of this I think I have a bad relay between the low pressure sensor and the clutch assembly. The only problem is I cant find it. Where this relay is located
View 8 Replies
I just had my solenoid changed and I changed the OD relay and my car still doesn't shift into 4th gear. Could the garage have put the solenoid on backwards? my switch on the shifter was replaced with a toggle switch from autozone. My volvo has 230K miles and it is a 1990.
View 17 Replies
Well it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 Replies
