Ford F-150 - 1997-2003 :: 1999 V8 Will Not Start / Truck Started Idling Very Rough And Died
May 6, 2017
1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
View 2 Replies
Advertisement
My 2004 F-150 Heritage with the 4.6 was running great until yesterday. Went in the store and left it idling, when I came back out it had died. First time it has ever done this. I started it and it started right up but misses bad. Checked it out and found all 4 cylinders on the drivers side are dead. The check engine light is on and the overdrive off light on the shifter is on. It will start right up and everything else is fine, oil pressure, coolant, etc.
View 9 Replies
I came home from work truck was running decent got up in the morning to start it up. Tried to start up was real rumbly and died got the same twice then went to just cranking over not getting anything else tried spraying some starter fluid in air and it would try so assuming its firing abd possibly gas related ...
View 4 Replies
2001 F150, about 3 weeks ago I drove through standing water that was probably about 2 feet deep, as soon as I did that the truck started jumping real bad and almost died. I drove it around for a little while and it started to run better. After that it started to feel like it was misfiring badly. Between 40 -50 mph on the highway just giving it gas a little the jumping was pretty bad.
I decided to change out the plugs, thought maybe water got onto them and this was causing the issue, this was my first time changing the plugs in the truck and it was not nearly as bad as it could have been! I was able to do all of the plugs except number 7. The fuel injection line is right on top of that plug and I did not want to remove it!
After changing the 7 plugs the truck is running better now, I have not yet felt the jumping that was happening, my problem is that on the 4 plugs on the passenger side all 4 looked to be covered in oil. My question is does this mean my head gasket is blown and how long do I have before I am going to have to put alot of money into this truck to fix this issue?
View 6 Replies
It has 100k on the clock. I bought it about 2 years ago and only put about 500 miles on it. It is only used as a farm truck. Historically it would periodically die at idle in park. Would always start up immediately and run fine. Plenty of power.
Today the truck started up and idled a few seconds and started idling rough. It died and would restart but has zero power. Put it in gear and it would die. Did this a few times now can't even get it started.
I checked all fuses. I checked the dist cap and rotor. Don't look the best but don't think this is the problem. I get the same result on both front and rear tanks. From what I have read sounds like a fuel pump or regulator. Where is the regulator located?
1997 F450 superduty 7.5 gas ...
View 1 Replies
I recently changed the heater core on my 99 F-150 which meant i had to remove the dash. I got everything back together turned the key to start it and nothing it wouldn't start it wont even turn over. All the electronics come on like normal it just wont start. I have chased every wire every connection into madness. It has an aftermarket remote start someone said that would have bypassed the PATS but i dont know about that the theft light just started blinking.
View 1 Replies
First of it's a 2003 with the 4.6. I replaced a bad alternator a couple months ago and all was fine. On the way home today the radio volume went quiet and all the dash gauges were dead. Truck died and wouldn't even try to start, no starter clicking or anything. A couple times the gauges did the "sweep" but still no start, not even a starter click. Barely even operated the hazard lights. Towed it home and hooked up the jumper cables to my 7.3 Excursion. Truck started right up and I left if hooked up for a couple minutes hoping to get enough charge in the battery to get it in the garage.
Unhooked the jumper cables, got in the truck and noticed the voltage gauge was reading nothing, tried to move it and it died. Hooked the jumper cables back up and let the Excursion charge it for about 5 minutes. Started, drove it to the garage (100ft) and backed it in. Noticed the voltage gauge was where it should be. Turned it off and back to run (didn't start) and the voltage gauge was reading good and it started right up.
Now, it doesn't appear that the battery or alternator is bad. Is there something else I should be looking at? I can take the alternator off and have it checked but don't want to go through the work if not needed to chase a ghost. Advance auto Tough One alternator BTW.
View 6 Replies
Went to start my truck up about 3 hours ago to take my ol' lady to work. Turned it over and acted like the usual cold start. Well soon as I thought it was good to let the engine spin, it got to about 300-400 RPM and then died. So I shut the vent off and turned my head lights off (turned them on soon as I thought it was good), spun the engine again and when it hesitated once again I gave it some gas like you would on a carb (not pumping just gave it half throttle or so) brought up the engine to about 3K and it ran just fine.
I'm not sure if its the fuel filter (when the last time my dad even bothered to change it since he has done most of the work on it in the time we've had it) or if the fuel pump is going out for the 3rd time in the last 10 years. The last time the fuel pump went it was a bad Walker fuel pump. It was promptly replaced with a Bosch and has been going strong for the last 8 years or so.
If it is the fuel pump, my guess is either my dad is going to junk it or fix it. With it getting close to 260K miles its becoming warn out and showing its age. Been pretty dependable and will do just about anything you ask and it'll do it even if it takes a long time to get going.
The fuel lines are pretty rusty so if its the filter chances are we'll have to put in a new section of fuel line in. Its probably running close to 135K miles on it since it was last done. I've only started doing maintenance on it the last 6 years or so for the most part.
View 2 Replies
So there's no signal/ electrical feed to the passenger side cylinders. I ohmd all the UVCH and they check out. Moved the wiring harness around near the big black multi pin plug under the air intake to the turbo and the passenger bank kicks in and out so it's definitely a wiring short. Need links and pics to that multi pin plug to troubleshoot the wiring.....
View 8 Replies
I have a 2001 F150 4.6L auto. This truck suddenly started running rough. Cleared all codes and re-scanned after starting truck. The codes are as follows; P0135, P0155, P0443, P0740, P0743, P0758, P1451, P1460, P1747, and P1760.
My question is; is it normal to have this many DTCs come up at once? Could my PCM be faulty causing this problem? Can you swap a pcm from the same year truck with the same options without reprogramming?
View 2 Replies
I have an 03 with a 6.0 diesel, going down the road and started losing power and then died. Won't start, and I don't have a scan gauge. Several sources said ipr valve, and from videos on youtube I thought may be a good place to start. I bought a socket and pulled the valve, to check the screen. There is no screen whatsoever on the ipr. The oils clean, as I had changed it about 200 miles ago, and I ran a magnet in the hole looking for a screen, couldn't find anything so I used my fluid pump in the hole. No trash, screen or anything. Do some ipr valves not have screens? What would be my next step??
View 2 Replies
My truck started to idle very rough. I pulled the codes and I got po308 and po316. First I changed plug #8, the electrode was nearly gone. I have never seen a plug in worse shape. Replaced that plug and fired it up, it still idled rough and threw the same codes. Next I moved the #8 coil pack to the #1 location and vice-versa, still the rough idle and same codes. Then I moved the #8 injector to the #1 location same results. Finally I tested compression in the #8 cylinder and it read 32psi ( not good) everything else read 150 to 160 psi. Squirted some oil into #8 and no difference in compression.The truck is a 2002 with 184,000 miles, it burns a quart of oil every couple weeks but still is in perfect shape. Should I bite the bullet and invest in a remanufactured engine for 2500.00? I put one in my 97 f 150 a few years ago with no problems.
View 5 Replies
My niece has a 1999 F150 with a 4.6L engine. She was driving it down the road and it died and would not start. She called her husband, he went where she was, and when he got there, it started. She drove it home, and the next day, same thing. Died going down the road, no start, let it sit overnight, cranked like a new truck. Now it has died and will not start at all. They replaced the fuel pump. Nothing. When you turn on the key, the fuel pump runs continuously. If you pour fuel in the air filter, it will start. They checked all the fuses, nothing blown. When they try to hook it up to an OBD scanner, it does not work. No codes, nothing, it won;t pick it up.
View 9 Replies
I have a F150 2001 6cyl. Other day was doing 75 on freeway and lost all power. I replaced fuel filter, and pump is humming good (was replaced 4 years ago) checked the Inertia Switch and checked all relays, but truck still wont fire. I checked spark first and that's good.
View 2 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
My 2000 f150 with a 4.6 and just about 200,000 miles stumbled for a minute then died, no engine light came on. It wanted to restart and almost did a couple time's but no go. which leads me to believe it has spark. after about a 30min cool down it started and ran fine like nothing ever happened. Got me home. then the next day same thing died and started after it cooled. Has done this a few time's.
I had put a cheap O'riely fuel pump in it a couple years ago. but i hear if you run your gas tank low on gas a lot (which I do) the pump can get hot and you can toast it. Does the fuel pump is the issue or could i have another problem. And BTW in the past year I have cleaned the EGR port's on the throttle body, put a new egr valve, and fuel filter. And i checked the fuel pressure to had 40...
View 6 Replies
When I start my truck it takes 30 seconds or so for the truck to start moving... especially when in reverse. If I give it some gas it doesn't take quite as long. I am not a transmission guy. I assume it has something to do with building pressure but I don't know what would be the cause. The fluid is full and looks good.
View 8 Replies
Last night my boyfriend took a friend to the check cashing store, truck ran fine. shut it off, and when he came out the truck would not start. it cranks over but won't start. Took ignition coil off and had it tested but its fine. What else could be wrong or what can i do to try to get it to start again.
View 5 Replies
My Truck : 1999 Ford F-150 Extended Cab 4x4 5.4L V8
So the other day I was driving the truck and it just dies on me. Tried starting but it just cranked and cranked. Got it pulled over to a parking lot and then tried to start and I got it to run again. Died a couple mins later uo the road and it will not start at all anymore. I got it towed to my driveway and I've started diagnosing some things.
I dropped the tank thinking it was a pump I replaced awhile back. The pump wasn't running but jumped to conclusions and took it back to the auto parts store. They bench tested and it works fine. I checked for voltage at the pump connector. NOTHING. So I'm not getting power to Fuel pump. Then I checked the fuse and relay for the fuel pump. Everything was okay.
I did some research and decided to check for spark. NO SPARK. Another thing I noticed the other day was that the odometer is displaying all dashes. So I'm really unsure on what to really troubleshoot. I am going back to the truck tomorrow to check a few other things. I'm not sure if the Theft light is blinking or not so I will check that tomorrow and get back to you.
What to check? Any other relays or fuses besides the fuel pump? What about any modules to check like PCM, GEM, etc. Or I've heard the crankshaft sensor could be an issue.
View 14 Replies
My 03 with a 5.4 has been hesitating a when you accelerate and cutting out as well as idling rough and die when you slow down. It does all this intermittently. Not every stop or every time you accelerate. I first got a code for the MAF and both banks running rich (PO102, PO172, PO175) so I cleaned the throttle body and MAF. The running rich code came back (PO172, PO175) so I then changed the MAF and air filter . It seemed to work for a day or so then my light came on and I figured the same code was back but to my surprise it was now both banks running lean(PO171, PO174) so I took my MAF back and got another one. It hasn't set a code yet but it is still running poorly. I have changed all the COP's and plugs as well ....
View 13 Replies
I'm running into a brick wall trying to get my GTI to start. This post is my last-ditch effort before just towing it to a shop.
A little over a week ago, the car just died while idling outside a buddy's house. Prior to dying, it had been having some sputtering starts and had been dying while driving as well (engine cut outs) for about a month, but it had always started right back up strong after cutting out.
First I tried replacing the crank position/engine speed sensor. No dice, still not starting. I had new spark plugs in the toolbox so I popped them in, still nothing. Then I realized that my spark plugs were totally dry when I changed them. I pulled the hose off the fuel rail, tried to start the car, no fuel. I had a more mechanically inclined friend come out with a multimeter and he checked my fuel pump and relay. He tells me the relay is good, but the pump must be fried because it's getting power but not pumping (I'm not certain of this as I didn't physically lay eyes on the multimeter when he told me this). The next day, I replaced the fuel pump and the fuel pump relay just to be safe. The car started! I thought I had it all figured out. I drove the car for two days and then, last night, it refused to start again. This morning, pissed off, I went back and was ready to tow it but it started right back up again on the first try. I drove it home, but then later when I went out to go grab a burrito it wouldn't start again. It cranks and cranks but just won't catch.
Pertinent information:
- I do have a CEL. Don't remember the exact code it's throwing but it's something like "Engine distributor circuit, no signal." The code cleared after installing a new fuel pump, but the CEL is back now. Could be a new code, though as I don't have a scanner.
- No other nasty dash indicators are on.
- With the new fuel pump, even when it was working normally, I never heard the usual "priming noise" you get when opening the driver's door. This is strange to me as I used to hear it all the time.
- The car cranks normally but I think it just isn't getting fuel, even with a brand new pump, plugs and relay.
- About a year and a half ago, the coil pack was replaced under the recall campaign.
After all these new parts, I'm thinking electrical. A ground short or something. But I've seen that for some people it was the ignition switch, or the IMMO, or the fuel injectors, etc....
View 2 Replies
