I came home from work truck was running decent got up in the morning to start it up. Tried to start up was real rumbly and died got the same twice then went to just cranking over not getting anything else tried spraying some starter fluid in air and it would try so assuming its firing abd possibly gas related ...
View 4 Replies1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
First of it's a 2003 with the 4.6. I replaced a bad alternator a couple months ago and all was fine. On the way home today the radio volume went quiet and all the dash gauges were dead. Truck died and wouldn't even try to start, no starter clicking or anything. A couple times the gauges did the "sweep" but still no start, not even a starter click. Barely even operated the hazard lights. Towed it home and hooked up the jumper cables to my 7.3 Excursion. Truck started right up and I left if hooked up for a couple minutes hoping to get enough charge in the battery to get it in the garage.
Unhooked the jumper cables, got in the truck and noticed the voltage gauge was reading nothing, tried to move it and it died. Hooked the jumper cables back up and let the Excursion charge it for about 5 minutes. Started, drove it to the garage (100ft) and backed it in. Noticed the voltage gauge was where it should be. Turned it off and back to run (didn't start) and the voltage gauge was reading good and it started right up.
Now, it doesn't appear that the battery or alternator is bad. Is there something else I should be looking at? I can take the alternator off and have it checked but don't want to go through the work if not needed to chase a ghost. Advance auto Tough One alternator BTW.
My niece has a 1999 F150 with a 4.6L engine. She was driving it down the road and it died and would not start. She called her husband, he went where she was, and when he got there, it started. She drove it home, and the next day, same thing. Died going down the road, no start, let it sit overnight, cranked like a new truck. Now it has died and will not start at all. They replaced the fuel pump. Nothing. When you turn on the key, the fuel pump runs continuously. If you pour fuel in the air filter, it will start. They checked all the fuses, nothing blown. When they try to hook it up to an OBD scanner, it does not work. No codes, nothing, it won;t pick it up.
View 9 RepliesI have a F150 2001 6cyl. Other day was doing 75 on freeway and lost all power. I replaced fuel filter, and pump is humming good (was replaced 4 years ago) checked the Inertia Switch and checked all relays, but truck still wont fire. I checked spark first and that's good.
View 2 RepliesMy 2000 f150 with a 4.6 and just about 200,000 miles stumbled for a minute then died, no engine light came on. It wanted to restart and almost did a couple time's but no go. which leads me to believe it has spark. after about a 30min cool down it started and ran fine like nothing ever happened. Got me home. then the next day same thing died and started after it cooled. Has done this a few time's.
I had put a cheap O'riely fuel pump in it a couple years ago. but i hear if you run your gas tank low on gas a lot (which I do) the pump can get hot and you can toast it. Does the fuel pump is the issue or could i have another problem. And BTW in the past year I have cleaned the EGR port's on the throttle body, put a new egr valve, and fuel filter. And i checked the fuel pressure to had 40...
Last night my boyfriend took a friend to the check cashing store, truck ran fine. shut it off, and when he came out the truck would not start. it cranks over but won't start. Took ignition coil off and had it tested but its fine. What else could be wrong or what can i do to try to get it to start again.
View 5 RepliesMy Truck : 1999 Ford F-150 Extended Cab 4x4 5.4L V8
So the other day I was driving the truck and it just dies on me. Tried starting but it just cranked and cranked. Got it pulled over to a parking lot and then tried to start and I got it to run again. Died a couple mins later uo the road and it will not start at all anymore. I got it towed to my driveway and I've started diagnosing some things.
I dropped the tank thinking it was a pump I replaced awhile back. The pump wasn't running but jumped to conclusions and took it back to the auto parts store. They bench tested and it works fine. I checked for voltage at the pump connector. NOTHING. So I'm not getting power to Fuel pump. Then I checked the fuse and relay for the fuel pump. Everything was okay.
I did some research and decided to check for spark. NO SPARK. Another thing I noticed the other day was that the odometer is displaying all dashes. So I'm really unsure on what to really troubleshoot. I am going back to the truck tomorrow to check a few other things. I'm not sure if the Theft light is blinking or not so I will check that tomorrow and get back to you.
What to check? Any other relays or fuses besides the fuel pump? What about any modules to check like PCM, GEM, etc. Or I've heard the crankshaft sensor could be an issue.
2001 F150, about 3 weeks ago I drove through standing water that was probably about 2 feet deep, as soon as I did that the truck started jumping real bad and almost died. I drove it around for a little while and it started to run better. After that it started to feel like it was misfiring badly. Between 40 -50 mph on the highway just giving it gas a little the jumping was pretty bad.
I decided to change out the plugs, thought maybe water got onto them and this was causing the issue, this was my first time changing the plugs in the truck and it was not nearly as bad as it could have been! I was able to do all of the plugs except number 7. The fuel injection line is right on top of that plug and I did not want to remove it!
After changing the 7 plugs the truck is running better now, I have not yet felt the jumping that was happening, my problem is that on the 4 plugs on the passenger side all 4 looked to be covered in oil. My question is does this mean my head gasket is blown and how long do I have before I am going to have to put alot of money into this truck to fix this issue?
I recently changed the heater core on my 99 F-150 which meant i had to remove the dash. I got everything back together turned the key to start it and nothing it wouldn't start it wont even turn over. All the electronics come on like normal it just wont start. I have chased every wire every connection into madness. It has an aftermarket remote start someone said that would have bypassed the PATS but i dont know about that the theft light just started blinking.
View 1 RepliesJumped in the 1999 cc dually 7.3 6 spd superduty.
Just rebuilt the rear locker ( FYI if you use new clutches Do NOT add clutches, it is TOO tight now) and rest of rear end.
Full of fuel, drove it half the day only minor issues. Cruise, Horn, 4x4, suddenly would not work, but it was running and driving like it always has.
Around lunch while at 55 mph it shuttered hard like it had stalled for a second. I stopped and checked the oil. It was just above the add but I topped it off and went one. The further I went the more it happened.
So I decided to head back to shop and switch it with the car i had left there. It finally died like it was out of fuel.
next day I take 5 gallons of fuel and put in it ( maybe the gauge is acting up like the horn, cruise and 4x4?), it brings it from 3/4 plus to full mark, so gauge is working accurate. I also keep a fuel log that says i went 100 miles since last fill up.
Get in, it fires right up. I leave it sit and idle while i park the car. About 5 minutes and it dies. It will start run a few seconds and die again. The more I try it the shorter time it runs.
Finally does not want it start at all. I read about disconnecting plug on inside left front of valve cover , that had not effect. Crawled under, and frame mounted fuel pump is running.
So there's no signal/ electrical feed to the passenger side cylinders. I ohmd all the UVCH and they check out. Moved the wiring harness around near the big black multi pin plug under the air intake to the turbo and the passenger bank kicks in and out so it's definitely a wiring short. Need links and pics to that multi pin plug to troubleshoot the wiring.....
View 8 RepliesWent to start my truck up about 3 hours ago to take my ol' lady to work. Turned it over and acted like the usual cold start. Well soon as I thought it was good to let the engine spin, it got to about 300-400 RPM and then died. So I shut the vent off and turned my head lights off (turned them on soon as I thought it was good), spun the engine again and when it hesitated once again I gave it some gas like you would on a carb (not pumping just gave it half throttle or so) brought up the engine to about 3K and it ran just fine.
I'm not sure if its the fuel filter (when the last time my dad even bothered to change it since he has done most of the work on it in the time we've had it) or if the fuel pump is going out for the 3rd time in the last 10 years. The last time the fuel pump went it was a bad Walker fuel pump. It was promptly replaced with a Bosch and has been going strong for the last 8 years or so.
If it is the fuel pump, my guess is either my dad is going to junk it or fix it. With it getting close to 260K miles its becoming warn out and showing its age. Been pretty dependable and will do just about anything you ask and it'll do it even if it takes a long time to get going.
The fuel lines are pretty rusty so if its the filter chances are we'll have to put in a new section of fuel line in. Its probably running close to 135K miles on it since it was last done. I've only started doing maintenance on it the last 6 years or so for the most part.
I have a 2001 F350 7.3l diesel.
My truck died the other day while driving almost like he ran out of fuel. Well he had fuel so I checked the oil and it was dry. There was an ugly puddle between the intakes and a whole lot on the ground leaking out. Also the puddle looked blueish.
Put in more oil and got him home but I can't find the leak. The only thing I've noticed is that the intercooler on the cold side came off slightly. A year ago I had to go mess with the UCVH and when I put it back together I had lost a dang intercooler duct clamp and replaced it with a sturdy ring clamp. Well it wasn't sturdy enough.
How much would this leak if it came off for a little while and how serious of a problem would I have as a result? I don't have any check engine light and as long as he has oil he runs fine.
Since I have reconnected the intercooler and idle tested the truck I can't reproduce the leak. I don't believe that a huge amount of oil is running through that intercooler because the turbo is lubricated through another system I have read. So what gives?
Also I am getting weird dip stick reading. For a little while when I ran the truck today he was showing WAY over full on the dip and then down again a little bit below the operating range line. Also there are a lot of air bubbles on the dip stick when it comes up. Way more than I am used to seeing.
Also, I really like the idea of cleaning my engine off really good. It's a frigging mess now. What precautions can I take to clean it up good without making a huge mess. Can I just go the car wash that has a degreaser hose and drain and just spray it down like nothing or is it sensitive and finnicky when wet? Cleaning between the intakes seems almost impossible without getting the whole turbo system out of the way. Should I be thinking about that?
On my way to work today it was raining so I turned my head lights on. All the dash warning lights came on and my truck had zero throttle response. I quickly turned my lights off. The truck went right back to normal. I turned my lights back on and nothing happened.
View 12 RepliesHere's what I have : 2003 F150xlt V6. about 65K miles.
Here's what happened : Drove it to the hardware store to pick up some stuff. Stopped in front of the garage. No abnormal indications during that trip at all. Decided to back to the garage and when I started it, it "ran" very rough and died in about 5 secs. Started again and chugged for about 2 or 3 secs. Tried a third time and would not run.
Here's what I've got : No CEL. all gauges indicate correctly. No anti theft blink. more than a 1/4 tank of fuel. in south central PA about at 35 degree day. parked level.
What I've checked : Wife turned the key on, I hear the fuel pump run a couple seconds with my ear in the rear wheel well. truck turns over fine. no start. turn the key off, about a two second buzz from the idle air control valve. when the key is turned on with my finger on the fuel pump relay, I feel it shift. I have pulled it and looked for corrosion. no problem. checked applicable fuses (visually).
I have tried to start with the IAC and MAF disconnected individually. tried to start it with a different key.
I have not : Banged on the tank to free up the pump. (I don't suspect it at this point)
I have not checked to see if there is fuel pressure at the fuel rail. Where is that schrader valve? I miss my books.
I have not verified that I have spark. What's the easiest way?
I have not modified my air intake in any way.
I'm headed out to a parts store tonight or walmart to get another scanner. I think my best clue here is the buzzing IAC. What's that mean?
Another "no start" issue... The details:
- 2002 F250 7.3L
- Rosewood stage two single shot injectors (rebuilt 1 week ago).
- DP Tuner
- Brand new OEM IPR
- ICP about two months old (OEM)
- New UVH's installed about a month ago
The issue: After installing the injectors and driving about 30 miles the truck died and will not restart. Had to have it towed home. Thus far, I've unplugged the ICP, switched out the CPS with a known good, replaced the IPR, checked the hpop simply by removing the fill plug on the top of the reservoir and gave it a quick crank - oil definitely came pouring out, removed valve covers and plugs to verify oil in the high pressure rails. Oil dummy gauge climbs after about 5 seconds of cranking and seems to hold.
Hoping it's not an injector failure as I just had these reworked. EDIT: Forgot to mention, not seeing any white smoke while cranking. Fuel bowl, full of fuel and fuel pump was replaced this past spring. What to check next? Tried taking a snapshot from a video to show the readings. The ICP seems low, and when unplugged shoots up the 2500, but still no start.
Last night when i left work I noticed my fuel pressure was running about 77 psi, it normally runs about 68psi. today I took my daughter to practice and it was around 83psi, on the way home it was up to 95psi, so I parked it and took another truck to work.
About a week and a half ago I lost fuel pressure going down the highway and the truck died, finally decided my pick-up foot must have come off and had my sister in law bring me some diesel and it has drove fine ever since. (it was right at a quarter tank).
I have the FRX from riffraff and am thinking some pieces of that foot have got into the fuel bowl and plugging up the return. Things to check? Could it be a problem with the fuel gauge or wiring, and how to test them. It is an autometer gauge from riffraff.
It will probably be a few weeks before I can do much more than clean out the fuel bowl. I don't have anywhere inside to work on it and it's been rain/sleet/freezing rain/snow for the last 10 days. I have most of the stuff to do the hutch mod and its next on the list but was hoping to put it off till spring.
On my 97, just had a new engine installed. Suddenly the Lo presser AC switch died. Now the Start Solenoid (I think) just clicks sometimes. Is this Solenoid on the Firewall the Start Solenoid?
View 6 RepliesI have an 03 with a 6.0 diesel, going down the road and started losing power and then died. Won't start, and I don't have a scan gauge. Several sources said ipr valve, and from videos on youtube I thought may be a good place to start. I bought a socket and pulled the valve, to check the screen. There is no screen whatsoever on the ipr. The oils clean, as I had changed it about 200 miles ago, and I ran a magnet in the hole looking for a screen, couldn't find anything so I used my fluid pump in the hole. No trash, screen or anything. Do some ipr valves not have screens? What would be my next step??
View 2 RepliesI have a 2003 Explorer.... 4wd..... and here's my story.. I had a tire blow out (front driver side) and I took it to a tire chain to get it replaced (it was the closest thing to where it happened and I had to get to work)
After the tire was replaced, the truck started to rumble in the front and seemed like the brake was being pressed while I was driving. I called the chain tire store and told them my truck was not doing this prior to them replacing the tire. They said it was fine because I was riding on a better tread tire and the remaining tires were worn.... (okay..maybe so?)
I drive 80 miles one way to work....the whole way there...rumbling and this 'brake applied' feeling. Worked my shift...drove the 80 miles back home...same thing.
Took truck back to store....they said that it was the Front Drive Shaft had cracked at the Transfer case.... I've asked a few people and they think it's just the ABS still locked because I was traveling a high rate of speed when my tire went out. I think the tire store chain screwed up when they replaced the tire....