Ford F-150 - 1997-2003 :: 1999 - Timed Engine Now Hard Start - Idles Roughly?
Mar 19, 2015
I have a 1999 F150 4x4 5.4, I pulled the heads due to blown head gasket. Prior to pulling heads truck started and run fine other than miss on #1 cylinder. I timed the engine according to Haynes manual and posts on this site. Truck is now hard to start and idles very rough. I does seem to smooth out when reving the engine and seems to have plenty of power. Cant find any vacuum leaks or unplugged wires.
View 1 Replies
Advertisement
1993 Buick Regal 3.1l V6 Multiport injection
Problem: The care currently has a hard start, and a fluctuating idle. I bought the car a year and a half ago it still has low miles about 94,000. The care used to start fine but had a fluctuating idle in the range of 750 to 2500 rpm. My brother who is a mechanic and doesn’t live near, do all the gaskets when he visited. Then the idle fluctuation dropped to 750 to 1000rpm, when the car rpms fluctuate there is a whirring sound I can hear from the cab, like a pump or pull system. On occasion there is a vibration as well but it is inconstant and irregular. Fuel pressure seems to fluctuate as well. If the car will not start I give it a little gas and it will run fine after a minute or two, but then the idle starts to fluctuate.
No fuse issues I can tell and relays seem to be fine.Checked for lose wiring connections found, none. I have replaced:
- Hoses and gaskets
- Starter motor
- Battery
- Fuel Pressure regulator
- Fuel Filter
- Spark plugs and wires
- TPS
- Idle Air control Valve
- Crank shaft sensor
- PCV.
Right now I’m thinking it could be the fuel pump (a nightmare to change on this car), a fuel injector failing, and the ignition switch.
View 8 Replies
I have the strangest problem on my 2006 Audi A6: whenever I fill up my tank with gas the car has a very hard time starting. This has happened 3 times in a row now. I run the tank fairly low - to about 1 quarter tank or a little lower but never to empty....then I fill the tank. When I get in the car to start it, the engine just keeps turning over trying to start but will not start. Then I stop trying, let the ignition rest for a bit, and try to start it about 5 minutes later and it starts just fine on the first try.
What could be causing this?One thing that has also started happening around the same time as the problem above is that when I'm idling at a stop light, I notice the car may start to idle roughly and seem like it is about to die out. I am the first and only owner of this car...I take good care of it and am an easy going driver. But I do drive a lot and have about 200,000 miles on it after 7 years.
View 2 Replies
06 F250 6.0 with only 65,xxx miles on it. This has happened twice and both times the engine was warm and had been cut off for less than 10 min.. When I tried to crank it back up it stumbled and idle roughly then cut off. After several attempts to re-crank it still would idle rough and I tried to give it fuel but no change, even with pedal fully depressed. Then it would die.
After sitting a few minutes it starts normal. Both times I didn't have my obd2 adapter for my torque pro. The last time it happened I went home and hooked it up and got no codes. Everything looked fine. What could it be, where should I start looking. Batteries are1.5 years old. Oil, oil filter, and both fuel filter changed about 1000 miles back. I have had the truck for 1.5 years and the oil has been changed twice.
View 2 Replies
its 1986 Ranger with a 2.9L V6 Auto 4x4, well to start with it seriously over fueling also it idles very roughly and even stalls out sometimes, when I'm trying to hold it at a speed it acts like it is missing (I guess that's from over fueling as well and it also pukes out lots of black smoke, it goes through way too much gas for a V6), but when I speed up fairly hard it acts fine until I try to maintain speed again, I have already put a tune up into it and a new EGR as well a fuel regulator and how to fix it?
View 14 Replies
The dealership did my oil change. Afterward, the engine idled rough. I drove home 50 miles and called and they said they may have overfilled the engine oil. The dipstick level is about 3 inches over the fill mark. What damage could result and how to approach the dealer about it?
View 3 Replies
Lately I have been having some trouble with 2002 Oldsmobile Alero v6. When the car is sitting in park I have noticed that the engine idles roughly, And when I try to drive it, the car hesitates on the acceleration every now and then. Also the emissions light (the orange one) will come on for awhile and then dissapear. At first I though it was dirty fuel injectors so I added some Fuel injector cleaner, but that has not fixed the problem. I was thinking the park plugs may need replacing?
View 1 Replies
Changed the spark plugs, but the engine still idles rough while in drive and stopped. It's fine in park or neutral. P0303 popped back on today while warming up the car. Changing plugs significantly improved the idle...but it still is rough.
View 7 Replies
I have a 2005 Ford Explorer 4wd with 4.0 SOHC 6 cyl Flex Fuel. For months the vehicle has idle rough and increasingly becoming difficult to start. I decicded to replace the spark plugs and wires hoping to solve this issue! gap set to 052. When I started the vehicle it went into engine fail safe mode and wrench light came on. I then replaced the TPS on the throttle body and had no diference (I may have installed incorrectly! when I put it on the armature felt like it broke free inside the sensor). DTC codes read P0223, P2106, P2110 and with P0122 pending, P0223 pdg, P2106 pdg, & 2110 pdg.
With the old tps installed and wiring harness disconnected the truck will start in fail safe mode, but will not start at all with wire harness connected. A volt meter reads at computer end of wire plug 3.69 volts at pin one (gray/red wire +) and pin three (gray/white wire -) with key to on but not running.
View 2 Replies
I have a 2002 F-450 crew cab 2wd automatic 7.3 diesel with 298k on the body and about 120k on a Jasper engine. About a month ago I started it in the morning to let it warm up. Went to make coffee. Came back and it had died. It was low on fuel and I didn't pay attention. Played hell getting it primed back up. Now if I don't let it warm up for twenty minutes it won't run worth a flip and has been dying out. Changed fuel filter. Unplugged ICP. No change. When I crank it it will turn over for about thirty seconds then oil pressure gauge moves, then engine starts to run very roughly. It will die. I repeat a few times. It will eventually start and start and stay running. Blows whitish grey smoke until it warms up. No loss in power till CEL comes on. Still not too much loss. Sometimes it takes a long time to get it running. Sometimes it will die after I get out of the driveway if I don't let it warm up. Truck was serviced maybe 3000 miles ago. No water in fuel. New fuel filter. New air filter. It is a company truck. I work for a small company building cell towers.
View 5 Replies
My high mileage V6 1999 Sierra starts fine and runs great in the morning or when it is cold. As soon a you try to restart hot is spins fast enough, but has a very hard time starting. When it does start, there is smoke from the gas and the engine idles very high for about 10 minutes before settling down. Same thing reoccurs over and over when the engine is hot. May idle up to 2500 rpm, cant kick it off.
View 3 Replies
2003 F350 7.3L 164k miles. Got towed in with hard to start cold complaint.
Hooked it up to the Snap On Verus Pro scan tool and we get up to 3000 psi on the ICP cranking, IPR value seems within spec, we have rpms over 100 on tool, pulse width within spec, computer voltage above 10v while cranking, verified output of glow plug module (California) and glow plugs get voltage for approx 50 seconds @ 80 degrees farenheit, glow plugs all read 0 ohms resistance.
injectors do NOT sound the same during buzz test.
Vehicle takes EXCESSIVE cranking cold to eventually get it started. LOTS of cranking. Just had to replace starter and a battery because driver burned em out. It feels like the vehicle shakes when it gets running. Black smoke when revving cold. Sometimes white smoke while cranking.
Once the engine has been warmed up, it starts perfectly every time.
I have spent two days in the engine bay looking for chaffed wires and doing diag and my current diagnosis is bad injectors. I feel there COULD also be high pressure oil leak, or a mechanical issue such as low compression. No compression guage yet for this truck. We have the ICP and IPR fittings to do a shop air test. Recently did a 6.0L and went thru everything and eventually diagnosed it as bad HPOP. LOW ICP pressure.
I noticed two of the cylinders were at maybe 8% Perdel on the data. Seems too high. Also, it "passed" the KOER self test and "passed" the injector buzz test with no codes after, but the audible sound of injectors didn't "seem" right to me, but I am new to these engines.
View 14 Replies
Truck seems to have a rough idle not bad I had kid in back seat and ran into store came out and he asked why my truck was shaking. Plugs been changed dunno anything else I could do.
View 8 Replies
So this is reason #345 why I should never have let my wife drive my F-350. I am in the Army, and I got a frantic call from my wife (I missed the first 7) saying that the truck died and won't start. I drive all the way to the truck, pop the hood and discover:
1) there is no coolant; and
2) there is no oil (actually just EXTREMELY low on both).
So, I do what any good Soldier does, I push the truck all the way back home (downhill mostly), buy 5 quarts of oil and a jug of 50/50 coolant, fill up both and try to start the engine.
The last time it ran out of oil (small leak on a seal that I didn't know about) in 2006, all I had to do was fill the oil, turn the key, and press the gas until it kicked over (don't judge me, I was a dumb LT). I did this again this time (now, I am a dumb CPT) but now it: 1) idles very rough; and 2) won't start unless I press down on the gas when I turn the key. There is no gauge light when it does this. I read the thread on the UVCH, but I am concerned I might have done something horrible to my truck.
2003 Ford F-350 7.3L
View 6 Replies
Engine will start and run but will miss in a pull and die sometimes but will start back, we hooked it to a scanner and it said (intake wiring) it wasn't a dealer hook up just a gas station garage, we have already done plugs and wires.
View 2 Replies
I recently purchased a 1996 Ford Ranger with the 4 cyl. engine. The first 10 days I owned it it ran just fine. I then took a an hour drive to another city. After the first few stops there, as the temperature outside reached about 90, It started to sputter and idle very badly. After I got rolling it would would run fine. I decided to try to make it home. It ran fine at freeway speeds of about 70 mph. I had to stop once; it stalled out and would not start again. After waiting about ten minutes I tried again. It was still running rough, but I was able to get rolling and drove the rest of the way home without any problems until I was in town and had difficulty keeping it running at idle.
The next morning it ran fine again. A local mechanic changed the fuel filter, but the problem came back as soon as the temp neared 90 degrees. A mechanic friend who witnessed the problem said that it definitely sounded like a lack of fuel and not an electrical problem. Is there a way to troubleshoot without swapping parts? If the fuel pump is failing in warm weather, how is it possible that it runs fine at 70 mph, but not at idle? Engine temp gauge looks good. I did get one code after it died the first time (lean mixture, I think he said).
View 5 Replies
I own a 2000 Ford Escort ZX2 with an automatic transmission. I also own a 1991 Fleetwood Cadillac with an automatic transmission. Each car has its own situation.
The ZX2 idles high (about 1000 RPM) and rumbles pretty roughly while idling. I was curious as to what the cause might be.
The Cadillac has a blown head gasket and I was wondering how expensive and what would go into fixing this myself or just how much it would run going through a dealer.
View 4 Replies
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 Replies
After sitting engine cranks longer than it usually did before it starts. idles a little rough. engine light comes on after it been running about 30 sec for 1 min. after that seems to run fine.check codes po446 and p1633 always come up. if you let sit a bit with key on starts right up.replaced gas cap checked evap lines, and changed filter no luck. Did notice with lines off evap solenoid key off or on i can blow through it. that doesn't sound right.
Checked fuel pressure. key on jumps to 90psi then falls to 55psi and stays. turn off key and leaked off 10psi in 5 min.start engine while watching gauge does the same as when the key on except it falls to 30 to 35 psi and bounces between them. i think this is way low. What is the correct pressure? Shut off engine and drops to 20 in 5 min. Next I plugged line on test tee going to fuel rail and tested same results as key on. the convinced fuel pump was bad since regulator and check is there. replaced pump. problem still there.
View 4 Replies
I have a 2002 F-150 4.2L that is hard to start when warm. Cold starts are no problem, except in the below 0 F stretch last winter. Also when it is a hot start it is not an issue. Only when it has sat for a few hours does it have an issue. The following is the list of things that have been done.
- New Plugs,
- New Plug Wires,
- New Coil Pack,
- New Fuel Filter,
- Clean Throttle Body,
- Clean Mass Air Sensor,
- Clean Idle Bypass,
- Replace EGR Vacuum Control Switch,
- Manifold Leak Repair (Ford Dealer),
- Throttle Body Stop Adjusted for more idle speed,
- Check fuel pressure (40 psi key on, drops to 35 psi static).
View 1 Replies
Driving the last week, gone about 10 - 15miles when all the sudden I noticed a stumbling in motor while going up hills. Got where I was going, shut her off and came back a few minutes later, loaded the kids and popped the hood. Nothing obvious but a vac hose from the vac reservoir(?) to TB was a little rough looking. Jumped in, hard to start - low on fuel or ignition and idled at 300 - 400 till throttle got it going. Has started and idled fine ever since. Raced home with the whole 15 miles stumbling up hills - repeated that every drive since after a few miles of driving. Warming the motor up prior to driving doesn't seem to speed up the problem - it takes a few miles to start. Assumed fuel pump at this point.
Got to work on it. Replaced the suspect vacuum hose. Nope. Checked fuel psi - 31 and 40 w/o vacuum. Doesn't hold pressure - reading conflicting things on whether the system should hold psi with key cycle. It doesn't - bleeds to 0 in minute. Replaced fuel filter, regulator and pump. Checked the relay and pump after install - good click and good hum. Felt like problem was gone but I didn't drive more than a few miles each time I checked due to pulling the bed for the tank work. Plus we dropped 30 - 40 degrees while working it.
Never a CEL but decided to checked codes.
Continuous pulled up Neutral Safety Switch that I replaced last year
KOEO - P0232 which I assumed was from pulling the inertia switch multiple times to do the fuel system work
One time I did get P1207(?) Cylinder Head Temp Sensor out of range. Got it once and never again. Curious..
KOER - has never found a problem
The cold seems to have lessened the problem making me think electronics. My BIL is saying #4 or #5 coil or plug. I am starting to feel like I am chasing a gremlin.
View 13 Replies
