Ford F-150 - 1997-2003 :: 1999 - Code P0500 - Speed Sensor Has Been Broken Off
Dec 8, 2016
So I'm getting code p0500 the question I have is will the speed sensor on the tail on my transmission cause this code on my 99 f150 4x4 . the reason I ask is because this sensor has been broken off . I'm hopeful it only control's my speedometer and is not related to the code . I've tried to remove what is left however in fear if I get it loose it may fall into the transmission. I will be replacing the speed sensor on the pumpkin this weekend . but the transmission it's the upper one is broke off below the surface of the transmission this is a manual transmission....
View 2 Replies
Advertisement
Vehicle is a 1996 Aero* XLT, 4.0 engine with 155000+ miles. I'm getting the P0500 code with the OD light blinking. Tranny is not shifting properly. Did not look at the speedo or check the cruise due to worry about making it to my driveway. I have had ocasion to set the cruise to 45MPH and at times it will drop out. I don't know the lower limit on the cruise. Is this speed sensor the same as the VSS...
View 9 Replies
2010 RX350 check engine light is on code P0500 came up it said speed sensor A...
View 1 Replies
Where the vehicle speed sensor is located on the 2007 es350. Reomoved battery and air filter box but just can't find it.
View 1 Replies
My car is now 24/7 with this error which is Vehicle Speed Sensor malfunction an there seems to be no way of solving it, symptoms are:
*Speedometer not working, needle always in 0
*Power steering not working
*Car wont past 3rd gear
*Check engine light and power steering light on
I checked all 4 speed sensors and the wiring looks good and they look good. Also if i hit a bump, issue goes away for a couple of minutes, until i hit another, etc, so looks like a wire or short circuit, cant tell. Is there a speed sensor on the transmission as well? where is located?
View 1 Replies
I have an 08 avalon w/ 281k miles. NEED to replace the transmission speed sensor (P0500 code thrown). Where is it located on the trans and what is the part #? I'm thinking about servicing the trans while I'm there but looks like a lot of "comments" regarding this transmission and the problems with servicing it!?
View 9 Replies
I have my dads 99 f 150 cel light is on. Scan came back with code cam sensor bad replaced the sensor and the light cam back on now I got 2 pages of codes from plugs and wires coil pack fuses, wiring harness to all O2 sensors to cats to even replace the engine and computer, where to start at. The bad think is i got to get to codes off and truck working with no light for the state to inspect it and get his tags. or the truck will have to be crushed, and i have 2 weeks. By the way 4.2 liter and manual trans.....
View 14 Replies
Recently, my I4 XLE camry with abs came up with a cel P0500 - Vehicle Speed Sensor A Malfunction. Where the vehicle speed sensor is located? i doubt this thing's hard to service, but so far i have no luck finding it.
View 13 Replies
1999 F150 4.2L 125K miles.... My problems started about a month ago. I had a P1506 error. The engine was running fine but received the error code. I replaced the IAC and the air filter. Engine still running fine. A week later I received a code for the Intake Air Temp Sensor (don't remember the code). The engine still running great. I bought a new Air Temp Sensor and noticed the wires from the Air Temp Sensor were rubbing against the belt and had been severed. I made a mistake when replacing the air filter of not checking the wires (confession is good right).
The engine also constantly ran a fast idle 2000 to 2500 at this time. I repaired the wires. The engine light went off and idle now starts great and smooth but when heats up will will go to 2000-2500. I then decided to replace the Air Temp Sensor hoping to fix idle problem. Engine still idle fast when warm. However, when I come to a stop and put in neutral the engine will take a minute but go down to normal idle after sitting. Engine light stayed off for a week. Now engine light back on with original code P1506. Idle is still not working correctly.
I feel like I made it worse than it was originally and not sure what to try next.
View 4 Replies
I have a 2001 Toyota Celica GT, automatic with 177,000 miles, it has been very well maintained. I started having a problem usually just after starting when it is still not completely warmed up. I try and shift it into reverse or drive, and the shifter says it is in those gears, but the car acts like it is in neutral. Once it gets a little warmer I can try it again and it will slowly shift into reverse or drive, usually though the rpm's seem to go a little higher than normal while it shifts. It seems to drive pretty well after this, shifting-wise, but not exactly perfect.
When it is completely warm though it usually drives really well - mostly I do a lot of highway driving. The transmission fluid is full, and looks perfect, nothing in it, not burnt. Previous owner had it changed a few years ago I believe. The check engine light is on and the codes are Speed Sensor A P0500, P0770 Shift solenoid E. My speedometer also works perfectly by the way. I don't have a lot of good shops around and I feel like the ones that are closest to me will see dollar signs in their eyes when they see that transmission code and will just try and replace the whole transmission right off the bat.
View 1 Replies
97 ranger 2.3l 5spd ... I keep getting p0500 code. the speedometer and odometer work fine. I understand they get they're reading from the OSS on the transmission. Now I also have the vss in the axle housing which I believe is what gives the ultimate speed reading to the pcm that way there is no need to ever adjust for axle ratio.
When using the torque app with my obd reader my OBD MPH guage does nothing until I get to about 55 then it bounces around randomly between 20 and 55 and once I hit 60 mph it reads correctly. I have tried 3 different vss sensors checked wire continuity from sensor to firewall examined the teeth/sprocket that gives the vss it's reading and it all checks out...
My questions are:
- What volts or ohms are supposed to come out of the plug end so I can test if the signal to the sensor is working
- Looking for wiring schematics for this sensor to pcm...my schematic only has the oss.
View 6 Replies
I have received the error code P1506 on my 1999 F150 which is I believe an idle air control overspeed error. It seems to run a little rough at idle but not too bad. At the advice of my Haynes repair manual and the advice of a friend I have already replaced the IAC valve and the PCV valve on the engine and cleared the code, only for it to come back again after 50K miles. I am not sure where to go next with the diagnosis/fix.
View 1 Replies
I have a 99 f150 with a 4.2 manual with four wheel drive I need to replace the speed sensor in the transfer case it looks a lot like the one in the rear end I've called the auto parts stores and they show nothing. What sensor I can use ? I did find one on rock auto that said it was for the transfer case but after looking into there part I found it was for a automatic ...
View 1 Replies
I tried the test mode (hold trip reset and turn ignition to run) this revealed that the needle for the speedometer does sweep from zero to max and back, could it still be the cluster? Is there something I am missing? FWIW the odometer lights up but does not work and all other gauges seem to be functioning correctly.
View 10 Replies
I've got a 2006 F350 5.4L.
The ABS light came on and it was throwing a 'rear speed sensor' code. I searched around and it seemed to be a common issue that the sensor goes bad and needs to be replaced.
I bought a sensor and replaced it, but in doing so, I saw that while the sensor was indeed bad (cracked) the wire right at the connector was corroded.
I replaced the sensor but the ABS light is still on the dash. Is it possible that they code simply needs to be cleared? I was able to read it with my OBD2 dongle and Dash Command App, but maybe I'm not able to clear it?
Or is it more likely that the corroded wire on the connector is the issue? (it wasn't fully corroded and I cleaned it up and sealed it.). It didn't look like I could pull the wires out of the connector, so I assume I'll need a new connector. What is the part number?
View 2 Replies
1999 F250 Super Duty 6.8 V10 4x4 157k miles
On Friday afternoon the ABS light on my dash came up, ran the codes on my SCT Livewire and came up with a "P0500 Vehicle Speed Sensor A"
What should I be going after? Rear speed sensor? Front ABS sensors? Transmission speed sensor?
Speedometer is functioning 90% of the time, twice in the last 48 hours it wouldn't then shift hard and I would pull off to reset.
I have looked over the search results and wondered if there is a way to test the sensor with my multi-meter? Seems quite a bit of people had flashing over-drive light's at the same time, which I do not.
View 6 Replies
My 99 F250 with a V10 had an abs light come on and then it would go off. Now the ABS light stays on and it drove fine for a little while but the other night the Service Engine light came on along with the ABS light. Tranny was shifting harsh, winding out and I scanned the codes and got P0500. Is it the sensor on top of the rear differential or is it the ABS light causing the problem?
View 2 Replies
I recently replaced both the downstream O2 Sensors in my 2000 4.2L F150 because I was getting a P0136 (Bank1 Sensor 2) code that I couldn't get rid of by cleaning the connector or fixing wires. 110K miles. Calif truck. No other codes and has always passed smog test easily.
When I pulled the sensors, the Driver's side unit was extremely sooty, as compared to the passenger side (bank 1). The code failure was on bank 1.
Is this normal or is there some rich condition on the driver's side bank that I need to check into ? Originals were Bosch, replaced w/ Motorcraft, if that makes any diff. One on left is driver's side unit.
View 5 Replies
1997 f250 LD pick up 5.4L engine 131000 miles
Here is my story week ago code came on p0153 bank 2 sensor 1
Slow response ... now I been reading around and some people say bank 2 is passenger side other say it is drivers side or bank 1 is where cylinder 1 is , the point is I'm confused here for bank locations and sensor locations .....
View 3 Replies
I've got a 99 F-250 6.8L V10 manual 4WD with no speedometer or odometer. The ABS and MIL lights are on. Code is P0500 - VSS malfunction.
This started when the previous owner hooked up some large LED backup lights to the factory wiring. Something smoked under the dash. He then moved them to a relay-switched +12V feed. He reported that the backup light fuse did not blow.
Ive tested the backup light fuse and the recently replaced VSS. Fuse is good and the VSS tests ok for Ohms and gives AC voltage when the tone ring turns. I pulled the fuse panel, GEM, and PCM. There's no visible damage anywhere there. I'm stumped. Tomorrow, I'll dig for any melted wiring under the dash....
View 8 Replies
I have a p0401 generic exhaust gas recirculation flow insufficant detected code on my truck I was wondering what would be the first thing to check to get ride of this code? my truck hesitates from a stop while excelerating to several thousand rpm. should I try replacing the dpfe sensor? what does dpfe stand for? do they sell this sensor at oreilys or do you half to get this a the dealership?
View 9 Replies
