Ford F-150 - 1997-2003 :: 1998 XLT - Starter Hitting And Engaging But Engine Not Starting
Nov 25, 2013
I Have a 1998 f150 4.6 XLT and recently it has been starting on and off. sometimes i will try and start it and wham! it starts right off. then other times I just here the starter hitting and engaging but nothing. Replaced the starter, solenoid and still nothing. It does have an alarm system but the alarm light doesn't come on, also had battery charged and its working fine. I am really fed up with this beautiful looking POS. Oh and the wiper motor needs replace.
View 5 Replies
Advertisement
I'm a relatively new F150 owner (just got rid of the 98 Ranger I drove since 99), so I thought I'd check in to see if I was overlooking something obvious. A few days ago, after driving to the store with no obvious issues, I went shopping (coincidentally for oil change materials) and when I returned to my truck it would not start.
Here is a bit of info:
Starter cranks over the engine.
Battery is relatively new, and has plenty of power.
I can hear the fuel pump kick on briefly.
Check engine light is on (EGR Valve fault).
Engine started with starter fluid.
Engine ran like normal after starting.
Finally, the vehicle started/ran fine for a few days before the issue occurred again.
Like I said, I'm not too familiar with the vehicle yet, but I'm assuming the issue must be with the fuel delivery system. I plan on replacing the EGR valve, but I am curious whether a faulty EGR valve cause a no start? Also, I'm wondering if it's more likely that the fuel pump is going bad, or something electrical is the problem since I'm under the impression that the engine stops sending fuel to the cylinder if/when the engine doesn't start quickly after turning the key.
View 6 Replies
I just got a 1998 F150 5.4l 4x4 autotragic. Was sold to me as needing trans, wouldn't start. Tossed in a new starter and solenoid, now I can hear the the starter turn crank pulley turns maybe a quarter inch and when I let off the starter it goes back to the same spot.
Fear is motor is locked, but question (i don't know automatics) is there any way that a bad trans could keep a motor from turning over? Truck rolls in neutral or drive, pulled the drain plug no water just oil. Tempted to just buy a running 5.4 with trans but if I can avoid that I'd prefer to.
View 3 Replies
I am having a problem with my 1998 F150 4x4. The 4WD is not engaging. It is a manual shift. I have checked the transfer case by turning the drive shaft in 2WD it is free. When I shift into 4WD it is does not spin freely. So I believe that is OK. I have checked the vaccum diaphram. It will move the piston when I attach a hose and pull vacuum on the inboard hose barb. So I believe the diaphram it self is OK. I am not sure if the hoses and selenoids are OK. They look fine. However there is a constant vacuum on the inboard hose line (red/pink color) wether I am in 4WD or not. Is this OK? How can I check the selenoids. If all this is OK, the next thing I believ it could be is the shift fork in the differential. Is that a difficult job? Do you need to pull the whole axle out to replace it?
View 14 Replies
ZERO problems except that car consumes oil.
I drove around a corner and hit a minor pothole.
Engine rpms went to zero. I pulled over and car would not start. Starter is so quiet I thought it was not engaging.
I put a chalk mark on serpentine belt and it is turning but the engine shows no sign of wanting to start...no spark I suspect.
I see no blown fuses.
The car has been well maintained and has 250k miles mostly highway. 2.4l LE...
View 10 Replies
I have a 91 RS 3.1 with a 5 speed that is not starting.
The problem started with the key not engaging the starter at all, a friend who is much better at electrical and we found the security relay switch behind the kick panel is not engaging on it's own. we manually engaged the switch and now the key will spin the starter but the engine is not firing up only spinning.
does the security relay switch control anything other than the starter engaging.
There is gas in the car. using a screwdriver and spark plug wire we have verified that we are getting spark.
View 4 Replies
I have a 98 F150. The motor was replaced three months ago and have had no problems until now. The truck had trouble starting so i put an alternator on it. Fixed for a while and then it started blowing fuel relay fuses. I replaced fuel pump and filter. Truck has trouble starting after sitting overnight. When I am driving and floor it, once it hits about 4,000 rpms, the truck bucks like its the transmission but the rpms drop and then pick back up. Fuel pressure is right where its supposed to be.
View 1 Replies
I have a 1998 Ford F150 with 4.2.. Started off a intermittent problem of not starting acct no fuel. Now will not start at all. Checked all fuses and relays.. Am not getting voltage at fuel pump. Changed ECM thinking that was the problem.. Have checked all multi wire connectors for corrosion and tightness. Am at a lost what to try next.
Also, not sure if its related or not. The turn signals and hazard flashers do not work. When I turn on the hazard flashers, nothing happens. If I leave the flashers switch on, the turn signal work. Checked all fuses and relays and they appear good.
View 2 Replies
I just bought a 99 F350 to replace my 01 F250 5.4 and I'm pretty stoked. There are several problem (some i knew about, some were surprises) 1 of which is the starter. The guy I bought it off said that every 100 starts or so (more like every 4-5) the starter sounds like it free-wheels but you just wait for it to stop, turn the key again (sometimes twice) and it engages and starts (although it takes a few seconds of turning over before it fires up).
I have a buddy with the same truck and he has had to replace his starter many times and I read in an old log book from the original owner that he had replaced the starter every 25,000kms (15,000miles). I am not the kind of guy who likes to fix things to have them break again.
SO my question is, WHY do the starters on these trucks keep breaking? What is the weak link? Is it possible to re-build one with better parts at home?
Is the problem partially because my batteries are only 650CCA and 750CCA and it takes more to turn this beast over? Could it be a bendix issue?
View 6 Replies
I have an 02 f150 5.4 4x4, drowned it a while back, thought i had hydro lock, crank can be turned by hand though as far as i can with a wrench, so internals seem to be fine, no bent or broken rods that i could tell, ripped everything apart cleaned it up put it back together, new fuses, new ignition relay, new starter, alternator and battery as well, turned the key to on and got all my electronic stuff back up, turned to start and it all goes dark, which i assume is because at that point its sending power to the starter, but the starter didn't turn or crank the engine...
So question being when i put my new starter on is it possible that i might have crossed a wire or something that would cause it to not crank? and due to the fact that I had water in it, and had hydro locked it, all my plugs are out, now I know that spark is needed for the engine to run, but shouldn't be needed just for the crank to turn right? question being is that once i fix the wires on my starter, I am looking for initial crank before start up, so do i need to put a plug or two back in and hook them up to make it crank? or will it crank without them? and yes I did replace all my fluids as well.
View 8 Replies
So I just bought a E99 f350 lariat. I wrecked the truck on the test drive and felt like the right this to do was to buy it. Finally have everything fixed and replaced on the truck and have run into other issues now.
While flushing the coolant system I started noticing that the starter was engaging randomly. After doing some research I found out it could be the GEM under the dash. Looked under the dash and I could here a sizzling sound and seen "smoke" /water vapor something coming off the GEM. And there is water coming through from the window/cab lights.
So. All the post I seen where from like 6 - 10 years ago. Where is the best place to buy a GEM? Will having the window replaced take care of the leaking issues on the window? What's the best after market cab lights? Cause I think they are leaking too.
View 6 Replies
2003 santa fe, automatic, front wheel drive, 4 cylinder.
I had problems with the starter not cranking. took it off to the auto parts store and tested bad. I bought a new one there from called a tough one brand name. put it in, and it grinds the flywheel and sounds like it does not engage the flywheel enough. to it back to the auto parts store, and tested it, and it seemed like the gear did not shoot out like it should. they replaced it with a second starter now that tested good before i left the store, put it in and it does the same thing.
1. Can this type of starter not throw the gear far enough into the flywheel ?
2. Can a voltage drop to the starter cause the same thing. Basically is it possible my wires are bad not throwing enough juice to throw the gear all the way forward.
I pulled the starter out and jumped it with the battery and it seemed to work fine, but on the car it just grinds.
View 16 Replies
Driving home in my 04, and it just died, no caution lights, still have battery power, and starter is engaging but engine wont catch, like no fuel or spark. Found no burnt out fuses, and checked the fuel pump relay. Pulled out the back seat, turned key and heard the fuel pump, so that is working, replaced the crackshaft position sensor, still no engine start.
Over 130k miles, 1.6l
View 1 Replies
Been awhile since I've been on here...guess that's a good thing! Current problem...about a week ago my car stalled after starting it. I had been running errands all day so the engine was warm. Started fine, and then slowly died. My husband replaced the IAC valve. (My truck had this same problem 3 1/2 years ago...it was the IAC).
After replacing this time, it seemed to be fine. However today, again after running errands, the engine stalled slowly after I had started the engine. It seemed like it was trying to stay running, but then just slowly died. I tried starting again and it stayed running, so I was able to get home. It seemed to run fine while driving home. Also, no engine light has come on. Wondering what could be causing this. Don't want to get stranded somewhere.
View 7 Replies
I got an 2001 f150 4.2l v6, 5speed. It started running real rough almost like it was hitting on only 3 cylinders I replaced the crank sensor and did a tune up on it along with a new coil pack and now it won't hit a lick the plugs are getting fire, it's getting fuel but, will not start it's not throwing any engine codes. Which leads me to believe it may have a bad ecm.
View 3 Replies
My aunt has a 1998 F150 with the 4.6 V8. with only 40,000 miles.
Two years ago when she tried to leave work the truck would not start, it would crank over, but it would not start. She had the truck towed home and we figured out it was her fuel pump went bad. She did not have the money at the time to fix it, so she let it set and drover her nissan around.
I know after sitting for a few years the piston rings will stake (rust) to the cylinder walls. Usually take the plugs out, and pour in some oil, PB blaster,etc....and let it sit for a day or so, then turn the motor by hand to free it up.
Well She decided to get it fixed finally, and had it towed to the local ford dealer after sitting in her driveway for two years. Ford calls her later in the day and tells her the battery is dead and wont hold a charge, and the engine is siezed/locked up. They tell her it needs a brand new engine and could cost $5000. + after all is said and done.
She calls me asking what she should do. I told her BS! it only has 40,000 miles, and it does not need a new engine. It just needs to be broke free from sitting. I told her to have it towed to my house and I will fix it.
So today she had the tow truck bring it out to me. Tow truck driver tells me that ford said it has a bad fuel pump ( we knew) and that the motor has a spun main bearing in the motor..and asks me if I was going to rebuild the engine.
I tell him the story on the truck and he shook his head..and said yea..Ford is Full of it! I call my aunt and tell her what the tow truck driver told me, so she calls Ford..and asks what they did to the truck? Ford said, the truck has a dead battery, bad fuel pump and a spun bearing. She asked them how do they know it was a bearing?
Ford said they got the truck to run but the engine made a horrible noise like a bad /spun bearing inside.
I asked her, how did they get the truck to run with no gas/no fuel pressure if the fuel pump is out? The only way they could is with spraying Starting fluid ( ETHER) into the motor and fuel injection motors HATE that..they will run like total crap...
Bang, etc. because none of the sensors are working correctly..and makes the computer go OH CRAP. It's the end of the world!
If they (ford service) broke the motor free..I wonder how bad they did it. Did they FORCE it and break something internal ( bent a rod, wrist pin..)? I can't prove it, if they did.
So the truck is at my house and I am going to check it out. I am still going to pull the plugs and put oil inside, turn the motor by hand to make sure it is not locked up or messed up internally from them "working" on it.
I have never heard of a bearing going bad by just sitting. I have never worked on a 4.6 mod motor..and I know nothing about how good or bad they are... but I am soon to find out!
View 14 Replies
After replacing the battery and starter...as well as replacing the alternator (bench tested good), I'm still greeted with one 'thud' when attempting to turn the engine over. The battery light is one in the dash. I've been through this scenario with more than a couple vehicles that haven't started in the past. I do the normal check the battery, wires, alternator, fuses, and starter. Somewhere along that line...it always fixes the issue. Not so here. I have to admit that I'm at a loss at the moment.
2001 F-150 5.4L
115k
Replaced starter
Replaced batter
Alternator bench tested good
View 2 Replies
The past week or 2 I have had an intermittent starting problem. Engine is turning over but wont start, but after i wait a second it will start up. I listened to see if the fuel pump was running and heard the whine. I checked the battery and the starter voltage and it was all good. i primed the fuel pump a couple of times and it started up on the first crank of the ignition. The truck runs great when driving and idling, no misses or loss of power that i have felt or heard yet. I am thinking it is either the fuel pump is starting to go or maybe the fuel filter is getting a little clogged up. Like i said up above this is an intermittent problem and that is why I am confused. Its a 2001 F150 4.6 4X4 ....
View 1 Replies
So i drive a 2001 F150 4.6L and over the last couple of years it has started pulling down and shaking heavily. I have taken it to mechanics and it always gave a code as a miss. well we replaced the coils and the plugs and of course it still has the problem. finally we did a compression test and it shows that #3 and #5 have no compression and the mechanic said it was either a blown head gasket, a valve or a cracked head. it has 230K miles on it so i was wondering what your thoughts on it were and also if it would be cheaper just to swap the motor.
View 2 Replies
I have a 1998 f150 4x4 with a 4.6 triton vin #w and only 150,000 miles but its smoking. On first start up everything is good to go but when the engine reaches operating temperatures it will smoke.
It does not smoke all the time, just on takeoff. Such as after taking off after sitting at a red light it will puff a cloud of smoke from both sides of the engine. The engine is smoking blue so I know its oil its burning.
I pulled the valve covers off last week and the engine is clean, no sludge or gum. Power is good, runs good, and has good compression. Why its smoking.
View 14 Replies
I have a 98 F150, 4.6L with approx. 245,000 miles on it. recently it started, then studdered a little bit and died. I managed to get it re-started, it then shuddered a little more although I was able to drive it back up the drive way and park it. Now, it will crank however it does not even attempt to fire. The sound that it makes when trying to start seems odd to me. Like the engine is just turning against a constant resistance instead of the normal starting sound. I tried shooting a little starter fluid into the throttle body and nothing changed. I pressed on the shrader valve and got a spew of fuel to come out so it seems that it might not be a fuel problem though it sure sounds like one. Just curious, what are the symptoms of a truck with no compression?
View 4 Replies
