Ford F-150 - 1997-2003 :: 1998 - Cannot Get It To Move In Drive Or Reverse
Jan 12, 2013
I have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 Replies
Advertisement
I was driving my 1998 Ford F150 the other day and pulled into a driveway. At that time, the transmission quit pulling like I put it in neutral. It shifts from park and goes into reverse but not drive. It has the 4.6L and is 2 wheel drive.
View 4 Replies
I have a 1997 ford aerostar van that i recently acquired through some family,when i got it it was running fine but has recently started having troubles.The Question i have is this i put my car in drive or reverse and push the gas pedal the car doesn't move.....we have tried putting transmission fluid into it and that worked temporarily. What it could be except just a bad transmission?
View 2 Replies
I have an 03 Escape that is very difficult to start after it rains, if I open the hood and let it dry out for a few days it starts fine, however if I put it in drive or reverse and press the gas it will not move... if I hold the brake while it is in gear and give it gas it does not rev up, however if I put it back in neutral or park it revs up. I normally cover the hood with a tarp to prevent this from happening however I was shutting the tarp in the door and a lot of water got in the floor board of the truck I sucked it all out, that night the radio started playing all on its own, I came out to the truck turned the radio off it stop went back in came back a while later and it was on again, so I pulled the fuse... but there are two buttons that stay lit on the radio the preset button 1 and 2 stay on all the time and I can not figure it out either. This is my beach truck I only use it for that purpose..however it is fall fishing time and I really want to go...
View 4 Replies
I have a buddy that has a 1998 f150 4x4 with 4.6l and 332836 km on it. It will go in to reverse but will not go in to drive at all. Is his transmission shot? Or is there anyway to test it to find out what the problem is.
View 4 Replies
Well I was trying out my four wheel drive today and it worked fine until I went to turn off switch, it would not cut off it is a 98 F150 switch is located on dash. It is stuck in four wheel high!
View 3 Replies
I have a 1998 F-150 XLT, 2WD, 4.2L, V6, just over 103,000 miles. My transmission shifts fine into reverse but when I put it into drive it is very slow to engage, sometimes it doesn't. I have to put it in drive, hold down the brakes, give it some gas and then it will engage and lurch forward. I have check the fluid level and quality. Both are fine. This just started to happen two days ago with no fore warning. No previous problems with transmission.
View 4 Replies
2002 f150 7700 with 5.4 triton and 4r100 tranny started chugging under acceleration and now stalls when put in D, 2 or 1. park and neutral are fine and reverse works perfectly.
Now when I put it in drive it chugs and stalls immediately... 1/10 times it will keep running but chug violently like its running out of gas. will get worse and stall if you press the gas. i can light the tires up for a block in reverse however.
Changed coils 1 2 and 3, IAC, bank 1 knock sensor, camshaft position sensor
View 5 Replies
I have a 98 F150 4x4. I had some trans trouble so I pulled it out and had it rebuilt. Now when it shifts into drive the rpms speed up right before it shifts. What is causing the trans to do this? It doesn't do it all the time, only if I take off faster the usual which is most of the time.
View 1 Replies
My t case will engage in 4 high and 4 low. so i know the switch and motor works because it go all the way to 4 low and i can feel the lower gears. BUT the front drive shaft is not turning because i know that the front diff is engaging just fine cus one I just fixed it and because when i put it in 4x4 the front drive shaft is locked in but when i take it out the drive shaft moves freely when i turn it by hand. But when I test it in gravel or mud the front wheels still ain't turning. So its gota be the t case. But what are the part that may be broken in the t case and if I can fix it wile its still on the truck.
View 4 Replies
I been working on this unit and I running into this
no foward
no reverse
no foward in and gear at all
I have to check pump pressure
I'm changing fluid and filter
1994 F53 460 CID will not move in drive or reverse - iRV2 Forums
View 5 Replies
I have a 1997 ford f150 5.4 litre truck and the truck runs real rough kinda surging in park and in drive and reverse i have a couple oxygen sensor codes P 0171, P0174, P0136, P1131, P1151 and an idle air control valve code P1506...
View 5 Replies
I have a 2001 f150 crew cab 4x2 82k miles 4.6 with a 4r70w. Was pulling it over a curb and it popped now it will shift into reverse and load the motor like its pulling against a wall. In drive it will move some but still will lock up and stop moving. I assumed something in the rear had broken from the way it would roll a few feet and lock. Replaced the rear and still have same problem. Is there something I can replace to fix a stuck park or does the transmission need replaced or rebuilt?
View 1 Replies
I have a 2002 f150 4.6L triton. I've been having problems with it making a clicking noise. It only does it when its in gear. I put it in park or natural I hear nothing. But as soon as I put it in drive or reverse and put a little pressure on throttle it starts to tick pretty loudly.
View 4 Replies
This is on my 98 F-150 4x4 with the 5.4 and 4R100. What happens is when I put the truck in reverse and get on and off the brakes, every time I do so a relay clicks. It sounds like it's right up behind the instrument cluster.
I stuck my hand back there and can feel the click resonating in the metal brackets, but I can't figure out where it's coming from. It's never done this before and I'm worried something may fail at an inopportune time.
What this may be? It's a really loud click too and only does this in reverse. Park, drive, neutral etc. are all fine. The odd thing is when I hear the click everything still works as normal, parking lights, brake lights, reverse lights.
View 10 Replies
I have a 98 F250LD, its a Lariat, so everything electric/auto. Shift on the Fly 4x4, 5.4, 188K, Factory rear air suspension. Typical Minnesota rust. Anyway, I just noticed in the last 75 miles or so, a drive-line vibration. There is nothing until 39 MPH. Then from 39-41 MPH there is a decent vibration. Stops until 50, then from 50 MPH up it is a steady vibration. I have already changed the u-joints in the rear shaft. I have pulled/wiggled on everything else I can think of with no luck of finding of anything loose.
One thing I did notice, is that the front axle is locked in all the time. How long it has been like this: years for all I know... I can flip the switch from 2wd to 4H and 4L. It all seems to work fine, I hear clicking, the 4x4 engages, the proper lights come on/off. The front axle will pull when supposed to. The transfer case seems to be working fine, but the front axle won't disengage. I am hoping this can be fixed cheaply/easily (DIYer), and also hoping this explains my low fuel mileage.
Front axle? Where to look or what to try and fix for the vibration?
View 2 Replies
My 2002 lincoln ls v8 140k miles doesn't move when put into reverse or drive 5 or even d4,3,2,1 , it just starts to roll back/forward when taken out of park. It has the gear selector with d5, d4,3,2,1 not the select shift. I was told needs new transmission, but before it stopped moving completely it was still driveable second slipped at lower speeds(mostly when looking for parking or in traffic).
I had made an appointment to bring my car to the shop and the same day is when it stopped moving. All this happen within a week during the week i constantly got an e where d5 was and on last day check engine light came on.
View 4 Replies
I have a 2008 GS350. Been having brake clicking when I move from reverse to drive and lately been happening more when driving regularly. Brought it in to Lexus to get the complimentary 19-point inspection and they said I needed new brake pads and rotors. I did do a search and found it can be issues with front spindles, sway bar, bushings.
View 5 Replies
I replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
View 10 Replies
I just changed my oil in my mk4 jetta 1.8L and after draining the oil, changing filer, and adding new oil, the car will not move in drive or reverse. Once I give it gas it will move but that's at the higher rpms. I am almost positive I didn't remove the transmission oil but I am just not sure.
View 12 Replies
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
