1998 F150, XL, 4.6, auto 138k miles. Idles perfect, give it gas 1 time, fine. Second time it sputters. Third time it sounds awful but will Idle perfect. Put in drive, bucks, sputters, jumps, and damn near dies. Threw code P1747 EPC solenoid. Next day truck runs perfect check engine light goes out. Two weeks go by starts to sputter again and check engine light comes back on. Bad ECM?
View 1 RepliesI've got a '98 F150.throwing codd 402, excessive flow EGR, also the oil pressure drops to absolute zero only when gear shifts but comes right back up. No knocking or other distress sounds in engine. I know I'm in need of an oil change. I already searched a bit and decided to swap out the DPFE sensor which I did purchase from the dealership. No code as of yet but what could that pressure drop be? Could a simple il change and filter fix that?
View 3 RepliesI have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.
My son bought his first truck, 1998 Ford F150 Supercab 4.6L Auto. (Proud of Him)
Salvage Flood Title, looks like engine been replaced. (Not so proud of him).
Anyway, vehicle seems to run and drive fine, however, failed emissions test.
P0125 Code pops up, Temp Gauge is not working, pegs all the way hot after truck is running, changed out Both ECT's in front of engine, one is right beside the other, I guess one goes to PCM and other to Gauge.
Now Gauge is reading all the way cold, let run for over 30 minutes and still shows nothing on Gauge...
P0306 (ok #6 missfire) with P0171 & P0174 --- Do I chase electrical or fuel or both. Afraid to assume anything but probably would normally address the misfire electrical first.... Don't want to go down that 'primrose path' if others have been there first!
View 4 RepliesMy 4.2L died all of a sudden, it cranks but won't start. Checked the harness side to coil packs, pos. signal but no neg. Tried a code reader keeps coming back link error. Does this mean PCM is fried?
View 4 RepliesI have a f350 2000 4x4 automatic 170.000 miles. Service light on and OD light flashing. I have code p1747 "EPC solenoid short circuit"
This code make that the engine runs slow without power and hard shifting. I change all the solenoid body and check all wiring.
Later using a voltmeter i separate EPC solenoid wiring and see that have 5 volt. If I don't accelerate more 2000rpm OD light is not flashing and truck works normal but slow.
When I accelerate more than 2000rpm OD light begin to flash and transmission fail more. I check that EPC wires mark about 0 volts when OD light is flashing. Transmission hydraulic system seems to be ok because oil is very red and clean. Maybe another sensor is making this failure....
It's a 1999 f250sd 5.4l auto. Has code p1747. Truck shudders and almost dies when you drop it in gear, put it back in park idles fine. I have read all the post on here about this and checked wires from trans up to pcm look and test well. Tested plug c1048 wires with the digital meter to body ground with battery unhooked and got 6.66k ohms on pin 11 circuit 925, 421 ohms pins 1 and 12. Plugged c1048 back to trans checked 925 w/y wire at plug c103 got 9.1 ohms back to trans. Is the EPC solenoid bad or is it pcm? I think its epc but want to verify before i take trans apart.
View 2 RepliesIts a 1999 f250sd 5.4l auto. Has code p1747. Truck shudders and almost dies when you drop it in gear, put it back in park idles fine. I have read all the post on here about this and checked wires from trans up to pcm look and test good. Tested plug c1048 wires with digital meter to body ground with battery unhooked and got 6.66k ohms on pin 11 circuit 925, 421 ohms pins 1 and 12. Plugged c1048 back to trans checked 925 w/y wire at plug c103 got 9.1 ohms back to trans. Is the epc solenoid bad or is it pcm. I think its epc but want to verify before i take trans apart.
View 3 RepliesF250 7.3L diesel started to flash OD light, goes into limp mode, code p1747. No other codes. Have had issues for a couple of years where the truck would not shift into gear for awhile; sometimes a couple of minutes till it would engage. Have done lots of diagnostics. Visual check harness. Have 12v on pins 1&12 on harness at transmission plug. Plug had some ATF visible, but cleaned it up and continuity good. (with 4" exhaust hard to get to connector).
Checked all solenoid wires with a DVM back to plug at PCM for continuity and shorts, all good. Pulled transmission pack and checked resistance on all solenoids except temp varistor all within specs. Removed Banks Trans Command and rewired tranny plug and pulled Ottomind chip from PCM. Still goes into limp mode and throws code. Did not see any bad solder joints or burns inside PCM by the way.
Seems like PCM right? But here is a complication to my issues. For over a year I have been having electrical issues like the radio not working and windows not working intermittently after starting up. After running for awhile or on restart would work fine. Sounds like the Instrument Cluster issues or relays.(?)
Will be pulling IC and checking for any bad solder joints. However, did not throw p1747 till just recently and now my radio has really gone wonky. It comes on when key is on automatically and then proceeds to cycle through settings; AM-FM-CD.
So questions are, "Is it possible that a bad Instrument Cluster can cause a p1747 code?" "Bad Ground to Tranny" "Can a bad PCM cause a electrical issue in IC??" "Are these 2 separate issues?"
2002 f250 7.3L, 4R100 automatic trans, ~180,000miles
Banks Stinger package, 4" exhaust, TransCommand, (now removed).
Looking for info on tranny code 18155 or p1747 is ? Car is 2001 and out of warranty..
View 2 RepliesI have a 1998 expedition 4.6 4x4 check engine light on od light flashing sometimes checked it and got p1747 code i was told epc solenoid or short on trans wiring. I already dropped the trans pan, looking for a step by step easy way to diagnose and find the short or if i need to replace any of the solenoids. I have voltmeter and taste light....
View 3 RepliesI am having a problem with my 1998 F150 4x4. The 4WD is not engaging. It is a manual shift. I have checked the transfer case by turning the drive shaft in 2WD it is free. When I shift into 4WD it is does not spin freely. So I believe that is OK. I have checked the vaccum diaphram. It will move the piston when I attach a hose and pull vacuum on the inboard hose barb. So I believe the diaphram it self is OK. I am not sure if the hoses and selenoids are OK. They look fine. However there is a constant vacuum on the inboard hose line (red/pink color) wether I am in 4WD or not. Is this OK? How can I check the selenoids. If all this is OK, the next thing I believ it could be is the shift fork in the differential. Is that a difficult job? Do you need to pull the whole axle out to replace it?
View 14 RepliesJust bough a '98 F150, 4.6L; drove it home and it ran great, lots of impressive power etc... Parked it my shop and getting it ready for safety check so I can register it. All I did was change the oil, oil filter and air filter.
Couple weeks have gone by, I went to start it and it does start & idles beautiful but it will not rev. I give it gas and it's like it's choking / wants to die. The signal lights are flashing super fast which I don't recall doing before. Battery wasn't holding charge so I installed a new one tonight; no difference. Alternator is good.
I have not checked the plugs yet because I don't think that would be the cause of an overnight change from running excellent to what it is now but I will check them.
I have a 98 f150 4wd with manual shift on floor (msof) and the 4wd will not engage. I've done research and I've learned quite a bit but still have an issue. In All the research I've done I have learned about
View 3 RepliesI have a 98 f-150 4x4 the abs light is on and I can't link with scanner or seem to find anything wrong I don't have front abs just rear. I hate lights and I've checked everything I can think of.
View 5 RepliesI have a 1998 F150 4.6 that has a misfire with no CEL. I have already tried the following: checked fuel pressure, change cam shaft sensors, changed coil, checked MAf seems ok, spark plugs and wires. On my scan tool it wont show any misfires when obviously its misfiring. When driving it will run good for about 10 seconds and then misses for about 10 seconds and it just keep going in this loop.
View 8 Replies1998 F150 XLT 4x4 4.6L Auto.
Bought this truck two months ago, the lot had the engine rebuilt due to bad bearings, so fresh motor. They forgot to recharge the AC, so I had them charge it when I purchased it. It blew icy cold every things until a few weeks ago. It wouldn't work, then randomly it would, then it would quit, etc. Today it's 97 and I had it on with my kids in the truck, hot air.
I tried turning it off and on, still hot.
I tried seeing if the temperature was stuck and moved it to hot, it got sweltering hot, back to cold, just warm air. There is no difference between vent and max AC.
I went to the store, picked up a refrigerant filler with gauge and a can of R-134. I hooked it to the low end of the system and was surprised that my pressure was about 60PSI. Great, they over filled it at the dealership. I released the pressure down to 40psi and checked, sill hot. I figured maybe something was weird and they might have mixed good refrigerant with bad and that's why it was intermittent.
I released all the pressure down to 0 PSI. I then put on the can of R-134 and filled it to spec. Sill hot air. I removed the harness from the pressure switch and jumped it, getting sparks when I connect the wire, so it's connecting, but still hot air, probably not the switch.
What's going on here? Could they have over filled it and killed the system or something? What is likely broken here? My heater works like a champ, my AC just blows environment temperature air.
Got myself into a tight situation with a truck I recently purchased and seeing if any of you have experienced the same thing or know what may be going on. I bought a 1998 F-150 with 213,000 miles and a 4.2 engine. When I test drove the truck it had a small chugging vibration, for lack of a better term, but the check engine light was not on and it seemed to run great while driving. No problem at highway speeds nor below.
On my way home the check engine light turned on which turned into a blinking check engine light and I knew I had been taken by a person with a diagnostic computer who cleared the codes. He made a comment about it turning on before but his "buddy" fixed the issue but I took his word because he seemed like a decent person.
I took it to a local shop and, if I remember correctly, error code 302 came up for misfire on cylinder #2. He changed the plugs and wires and it seemed to run a lot better. About 5 miles later on my way home the check engine light turned back on, but it still seemed to run smoothly by the time I got home.
The next day I took it back to him and this time we got the same error code plus (again going of my poor memory) error 174 which he said was cylinder #2 running lean. Earlier today he called and said he checked over everything and couldn't figure out anything wrong until he checked the compression. He said the other 5 cylinders were around 130 psi and cylinder #2 was at 75 psi.
Now this mechanic runs more of a brake and exhaust shop so his next statements are why I'm coming to all of you for your opinions.
He said the cylinder was shot and everything inside was shot including the piston, rings, and everything else associated with #2. (I don't think he got in there to really check it out) After scouring the forums I hear more people talk about the valves may not be sealing correctly and what sound to me, to be smaller issues than the entire #2 cylinder being toast.
I'm not sure if I am going to go after the person who sold it to me or not yet but I would like to see what others may think is going on before I light this guy up. I plan on taking it to a more proficient mechanic to do the work, if deemed worthy of work, but would like to kmow where I stand.
ran fine the day before, fuelled up that night, next morning it did this. cleaned the IAC, tried a different TPS, cleaned mass air flow sensor. check vacuum lines. put couple bottles of gas line anti freeze in.
[URL]
'98 F150. the speedometer isn't working, all other gauges are. Where do I start ?
View 13 Replies