Ford F-150 - 1997-2003 :: 1998 4.6L - After Rebuild Turns Over But No Start - No Fire?
Aug 10, 2014
1998 F150 with 4.6L Windsor SOHC. I just completely rebuilt the engine including pistons, rings, timing chains (timing is good; compression @ 180 psi), 2 new coils, wires, plugs etc. and there's no fire at the plugs when I crank it. It turns over good but doesn't start. The fuel pump comes on and there's fuel up to the injectors. Before I disassembled the engine, it still ran good except for one piston. The 2 new coils, wires, plugs were replace before I rebuilt it. I was very thorough when re-installing the electrical etc... and triple checked it all after the engine not firing. Fuses are good. I know it's hard to trouble shoot without seeing the truck? The battery has been disconnected for months as I started a long time ago. Computer maybe?
View 6 Replies
Advertisement
I just got a 1998 F150 5.4l 4x4 autotragic. Was sold to me as needing trans, wouldn't start. Tossed in a new starter and solenoid, now I can hear the the starter turn crank pulley turns maybe a quarter inch and when I let off the starter it goes back to the same spot.
Fear is motor is locked, but question (i don't know automatics) is there any way that a bad trans could keep a motor from turning over? Truck rolls in neutral or drive, pulled the drain plug no water just oil. Tempted to just buy a running 5.4 with trans but if I can avoid that I'd prefer to.
View 3 Replies
My 01 F150 5.4 with 208K miles is having a starting issue. Did it again today, turns over, but won't fire. Problem has occurred a couple times in the past, but started after just a couple time of trying. Today however it took many times of turning it over I would say 5 or 6 times before it started. Seems like it's turning over kind of fast as well (faster than normal). Runs fine after it starts.
View 14 Replies
All of a sudden wouldn't start Saturday morning. Turns over fast. No fire. Waited a while and tried again and it started and ran fine. It did it again Saturday afternoon, so I changed the fuel filter. Gas from filter was very dirty. Still did it after filter change, so I replaced the fuel pump relay. Still did it twice on Sunday. Once it starts, it runs perfectly. Drove it 200 miles without a problem until I killed it. Then it wouldn't start.
View 9 Replies
I just picked up an 02 Supercrew. It came with a “Ford” remote starter. I imagine it was a dealer install for the previous owner. Anyways when I try to use the remote starter, it will crank the engine over but not fire. If I manually start the truck it fires up immediately. How come the remote start wont fire?
View 7 Replies
2000 ford f150 4.6 auto. Will spin over but won't start. checked coil for fire, no fire. Check fuel rail for fuel, no fuel. No theft light flashing and no check engine light on. Has new battery and plenty of fuel in tank. Started fine yesterday but not today.
View 5 Replies
My girlfriend has a 2003 f150 4.6lt pick up its a great truck most of the time. Problem is when the temp gets in the neg double digits it becomes very hard to start it cranks fine but doesnt want to fire. When it does fire it might stall a few times before it stays running. The last cold snap we had I replaced the battery and in the summer the starter got changed. I have heard that this model of truck are known for hard cold starts. I am just wondering if this is true and any other thing besides block heater. It is strange that my 89 gm pickup will start no matter what temp and I'm having problems with the newer truck.
View 1 Replies
Have a 2000 F-150, 5.4L. Once recently in a parking lot, it would crank but not fire or start. Wife called me to come get her. By the time I got there, she said it started "after she loosened the gas cap & re-closed it." But, it started fine for next several weeks. Yesterday it didn't. I read a bunch of threads here on possibilities. Many troubleshoot items I checked out or had done.
Chilton manual says you can get limited error codes from the light on dash flashing - MIL - Malfunction Indicator Lamp Method.
For now, I'm trying to find the 2nd, separate, one-wire lead "near or with the (main) Diagnostic Connector." They call the single wire / connector the "Self-Test Input connector" (STI). You're supposed to use a jumper between that STI & the upper, right connector of the main diagnostic connector. Then you (may) get flashes corresponding to codes via the key on, engine off method.
I see no such single wire lead or connector anywhere near there. Not up under the dash either - stuck my head under there & used mirror. There's a separate connector (not in use) clipped on the L side of the main diagnostic connector, but it has 5 pins inside. I took pics, but forum says I "may not post attachments." Been a member for yrs. That extra 5 pin connector faces toward firewall.
There's an "empty hole" - 1/4 in. (facing forward) in the bracket that holds the main diagnostic connector. Just above the main connector. Not sure if something was ever there
If no one knows how / if the Malfunction Indicator Lamp Method works or where the jumper goes, I'll be forced to buy a code reader w/o researching which are decent or crap (around $200 or less). I maybe? could wait to order one online (if knew which one). Also have AutoZone, O'Reilly, Advance, NAPA, PepBoys & others locally.
* The truck shows a check engine soon light, so should be a code already. * Yes, I tried her loosen / tighten gas cap trick.
* Also put a slow charger on for a while & even used the fast start setting on charger. No go, but engine turns really fast.
* Crawled under the gas tank & listened for fuel pump to activate when key is turned to Run.
* Fuel pump made a small noise - more like a relay or "clicking" - not a whine or whir.
* Checked most fuses - under dash & hi voltage box - that have anything to do w/ fuel pump, PCM & several others - mentioned in similar threads here.
Can't really check relays & don't want to just start replacing parts. I don't have a code reader & reluctant to buy one from local store w/o some reasonable research. (I don't mind buying one, but...). If I could drive it to the auto store, I wouldn't be asking this. Chilton's doesn't say if this malfunction indicator lamp method will work if a vehicle won't start. But, a code is already thrown.
View 6 Replies
I have a 97 jimmy that won't start. I have changed the fuel pump, checked the crank sensor, replaced wires. it gets fuel turns over but won't fire.
View 3 Replies
One month ago. I am at a store and it won't start. Turns over for a second but wont fire up. Waited a while and it finally did. Took to auto parts place and we went over all that it might be. I checked the button on the passenger side and it was down as it should be. I replaced fuel fuse 48 in the box under hood. All was well for a week
3 weeks ago again wont start but this time it will turn over and over and over. Waited again and it cranked. Went back to auto place dude said maybe the ground to the computer. So I put a neg ground on it to the frame. Worked for a few days.
1 week ago Again cranks but wont fire. I take it to the ford house expecting expensive sex. They kept it for 2 days and it cranked all the time. They told me it had to not start so they could get a code. Check engine light has never come on. Even when it wont crank. I got truck and went to eat. And yes then it wont crank. Waited and had another marg and it finally cranked but you could smell gas like it was flooded. Took it home.
Today I took it down to auto place and tested fuel pressure. 60 psi no problems. grrrrrrr well maybe it ain't fuel pump. I have to have a truck I can rely on. I have football playoffs coming up and I travel a lot. It has a brand new interstate battery. I put Lucas gas treatment in tank. Dude at auto place said it would clear fuel line and lube fuel pump? It was 10 bucks for big bottle so I figured it couldn't hurt.
If its 10 at night and I am at a game shooting THEN Im sure it wont start.
View 14 Replies
2001 F-150 5.4 extended cab
You have probably seen this before. Engine cranks but will not start. Backed into driveway, loaded recyclables, truck would not start. Fuel pump relay clicks, a small amount of gas comes out of the schrader valve on the fuel rail when I press the stem with a phillips head sd. When the engine is cranking the check engine light is on so I assume the computer is working but there are no RPMs showing on the tach. At this point I'm thinking a bad crank position sensor. Would that sucker go all at once like that? I believe they hid that behind the ac compressor. Am I looking at removing the belt and compressor to get at the sensor?
View 3 Replies
1999 F-150 XLT 5.4L Triton 4x4 super cab with a 4" body lift. I bought it used. It has 225,000 miles with engine and transmission rebuilt. This truck doesn't get driven every day - sometimes sits for a week or so at a time...
Issue: A couple weeks ago, it took 4 or 5 attempts to get it to start. Once it started it ran fine and re-started fine. Then my wife drove it but parked it back at home with the gas practically empty. Then it sat for at least a week or so before attempting to start it again. Now it just turns over and won't fire. I suspect fuel pump relay, fuel filter, or fuel pump (hoping its not the latter)
What I have done so far:
1. I put more gas in it in case it really was skimming the bottom of the tank.
2. I tried cycling the key several times thinking that maybe the fuel line just needed to prime.
3. I don't hear the fuel pump "whine" for two seconds when I turn the key to just before start.
4. I checked the fuel pump relay fuse (#10) - not blown
5. I have swapped thet fuel pump relay (#301) with another relay
6. I put 12 volts across the just the relay and I can hear it picking up and dropping out (when not inserted into slot 301)
7. I put my hand on the relay and had someone else turn the key and I can feel it picking up and dropping out (when installed into slot 301)
8. I went and checked out a fuel pressure tester from auto zone and connected it to the schrader valve and got 0 psi while turning the engine over.
All this points me to the fuel pump, but I am not looking forward to dropping the gas tank. With 0 psi, I doubt the filter is just clogged. I would still get some kind of pressure at the fuel rail, right?
View 10 Replies
2001 f150 4x4 5.4 205k ... This truck is not my daily driver but I use it about once or twice a week. Last night I drove it to the store and it ran great. As good as ever.
This morning it won't start. It cranks and the battery is strong but no bang. It was cold. Just below freezing for the first time this year. No blown fuses where would you start?
View 13 Replies
I have a 99 F450 bucket truck. I was up in the bucket when the engine died suddenly. It turns over but won't fire. I have no dash warning lights now either but everything else seems to be working. Lights, radio, annoying beeping sound from the key left in the ignition, etc. There are roughly 5 or 6 fuses in the panel to the lower left of the steering column that don't have power to them. Are they all supposed to have power when the ignition is on? I checked the fuse panel under the hood and all of the fuses that have 12V to them are good. There are a few small ones that don't have power to them but I don't think they do all the time.
View 9 Replies
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
View 1 Replies
My 05 GP randomly decides not to start. it turns over well but no fire . Sometimes even when I just stop for gas when its already warm. if I leave it for a few minutes usually it will start, run a little rough for a minute then run fine till next episode. no faults show up. I was thinking maybe the fuel pump relay was acting up.
View 2 Replies
What might be going wrong with my 2003 Celica GT? The problem is that it infrequently is taking longer to start. The starter turns over the engine, but it does not fire. It continues for a considerably longer time to crank the engine, then finally it fires and starts. Could it be that the fuel pump is beginning to fail?
View 3 Replies
I can cold start my 98 f150 with the 4.2 and it runs fine. After you drive it for a while and turn it off and try to restart it, it starts then dies, it will do this until you rev up the motor to keep it running. I have to drop in gear and get going down the road and then it smooths out and runs fine. I had a mech check the fuel pressure at the rail and it was 19 psi. The book says it is suppose to be 35psi. He said my fuel pump was bad. I installed a fuel pump and it is still doing the same thing yet. What to check now?
View 14 Replies
I have a 98 F150, 4.6L with approx. 245,000 miles on it. recently it started, then studdered a little bit and died. I managed to get it re-started, it then shuddered a little more although I was able to drive it back up the drive way and park it. Now, it will crank however it does not even attempt to fire. The sound that it makes when trying to start seems odd to me. Like the engine is just turning against a constant resistance instead of the normal starting sound. I tried shooting a little starter fluid into the throttle body and nothing changed. I pressed on the shrader valve and got a spew of fuel to come out so it seems that it might not be a fuel problem though it sure sounds like one. Just curious, what are the symptoms of a truck with no compression?
View 4 Replies
Vehicle is stranded on the side of the road (safely) and here's what happened. Driving (normal) 1/4 mile away from the house, motor shut down. Pulled off, tried restart. Motor turns over normally and all gauges work (temp/oil/volt). The only weird thing is that the O/D light on the end of the shift selector stays on even after pushing it on and off. I plugged in my OBDII reader and it will not link with the system. Yes... the ignition is on Is this indicative of a fuel, computer, electrical issue? or all the above. Worst case scenario is i have it towed to the shop tomorrow and they diag it. I don't have the proper tools to diag this.
View 9 Replies
I only see it on start up, after it starts I don't see blue smoke or smell it could this be valve guide seals? If so are they hard to change? This truck has 168000 miles on it and has a 4.6 engine.
View 3 Replies
