Ford F-150 - 1997-2003 :: 1994 - Under Quick Acceleration Bucks Violently And Die?
Nov 24, 2013
E 350 with a 5.8 drive ability headache 94 E 350 with a 5.8. about 1/2 throttle or under quick acceleration it bucks violently and will die if you don't let up on the throttle. This all started when it was run out of fuel. I found the condenser wire was shorted to its own body. Causing the PCM fuse to blow. I have since replaced the condenser. Same problem exists. I have replaced the map sensor with a known good one, same with the O2 sensor.
The TPS is in range and goes through its range smoothly (this was done on my scanner) Also replaced the fuel pump either due to the fuse blowing or running it out of fuel it wasn't working. Fuel pressure is 30 to 32 psi. I've checked the EGR for leaks and proper operation. I have noticed its very hard to start when its cold. Someone has had problems with it in the past as cat is new and i have noticed some things have been removed or replaced recently. The van was just purchased a few weeks ago by my buddy.
View 8 Replies
Advertisement
2001-F150 5.4 Eng. bucking/stumble. I think my problem is slightly different than what I am reading about. Here is what I get (125k miles):
* Engine only bucks/stumbles intermittently and not at idle or at harder acceleration (this bucking is really harsh and makes the truck feel like a learner trying to drive a manual transmission and it is jumping down the street). The engine stumble is not a regular timing such as a cylinder going out and staying out for a period of time. It is quite a random pattern to the jumping
* Originally thought it was humidity related, but now I realize it happens in any climate
* No stumble in neutral at any rpm... only at a stop if I put it in a power brake load.
* When the stumble shows up, it seems like the throttle is around 10-25% (my best guess)
* Sometimes goes days without issue, but sometimes every ride and virtually every acceleration.
* Normally no stumbling at highway speeds, unless going up a hill.
* Every time it stumbles, it can be eliminated by either backing off on the accelerator some, or hitting the accelerator harder.
* No engine codes or CEL has ever come on
* Fuel mileage appears to be the same before and after the trouble started
Here is what I have done to try to correct it:
-> Fuel related (bad gas)... tried to run the tank as close to empty and fill it with fuel from different stations... when this didn't work, I have added HEET to it to dry up any water in tank.
-> Fuel delivery... replaced the fuel filter... seemed to work for one day, but then the gremlins came back.
-> Fuel delivery... ran multiple injector cleaners through tanks of gas.
-> Intake... replaced the filter.
-> Electrical... I don't believe this is related, but my battery died... parts store tested the system and stated the alternator was bad... replaced it, and took the old one to the parts store for bench testing and it was 100% OK... even thought the old showed OK, I left in the new one as a precaution. Only other item was a set of plug changes around 30k miles ago... I think I put in the super duper Bosch plugs with a lifetime warranty.
Current thinking and items I don't understand:
A) The bucking is so severe, it appears to be a random harsh loss of either fuel or ignition. A component that has failed electrically should give me a fault code with this level of severity. No trouble codes or indicators to electrically sense this disturbance...
B) For the fuel path, the most likely item is bad gas and I emptied my tank by running it as close to empty as possible and then used different gas and HEET to eliminate water. THIS MIGHT STILL BE THE CAUSE???
C) Another one for the fuel path is an intermittent fuel pump electrical connection or a weak pump from a pressure point. But if this is the cause, then why does it dissappear upon harder acceleration?
D) One last fuel thought is injectors... perhaps one or more have a range of delivery that they don't work properly... but this doesn't make much sense as at idle and harder accels are fine
E) From an ignition standpoint, perhaps I have failing COP's. I have not just gone out an replaced them due to my limited budget and the difficulty I read about changing them. Again, if one of these is failing in an either open or short condition, the computer should set a code for a misfire for the related cylinders. I get nothing. Hence my hesitation in making this change so far.
One thing i don't understand from the various posts is that the cops can fail under loading. what makes this happen as electrically, i don't think they can detect a load or not? it is hard for me to also understand why my truck would allow me to back off on the throttle or hit it harder and the issue disappears.
View 14 Replies
97 F150 4.9 200xxx 5 Speed .....
I'm having an issue with my truck. It only seems to happen during warm 80+ weather. In the mornings, and during colder weather, the truck runs perfectly.
My problem is; Every time I go to get going and feather the clutch, either in 1st or reverse, my truck bucks wildly.
I changed the plug wires about 500 miles ago, and am about 4000 miles on a rebuilt engine (plugs as well) and new clutch/resurfaced flywheel. The clutch reservoir is full and I haven't noticed any leaks. There have been no codes thrown.
Could it be a possible fuel problem? I think I changed the fuel filter about 7k-10k miles ago.
I was also wondering if the Gotts mod could be causing it. I did the mod during the winter time, and this is my first summer with it on. My air filter is fine.
View 3 Replies
2001 F150 4x4 harsh shaking. When driving at consistent speeds the truck begins to shutter and shake, begins as a light shake and becomes extremely harsh fast. This is not like a vibration that can be felt, but a really harsh shaking of the entire truck.
The truck continues to shake after taking foot off gas and braking. It will shake harshly even when braking and slowed down to 5mph, but instantly goes away once at a complete stop. Accelerate immediately after coming to a complete stop and it completely goes away and drives normal for a day.
Check Engine light has not come on. Tachometer stays consistent RPM. Shift into neutral does not stop shaking. Only coming to a complete stop ether in drive or neutral does the shaking stop. It happens driving at consistent speeds going 35mph & 65mph, etc. Any thoughts on what the issue could be?
View 5 Replies
I have a 2003 impala I just bought and it has an intermittent problem. Sometimes when I step on the gas the motor will 'slam'---kinda like if the motor mounts were bad but they look good and it doesn't always do this. Also, if I hit the gas pedal hard and then almost as quickly let off the gas pedal I get the same effect--shutter/slam. I suspect the mounts but they look fine. If I keep on the gas all gears shift very smoothly. Gear shift is smooth thru all gears if I floor it or go slowly accelerate so it seems not to be the transmission either.
View 5 Replies
It just started doing it the only way I can seem to figure out how to explain it is at about 50 to 60 under slight acceleration or uphill it bucks or jerks like you have a trailer jerking. No check engine light this thing is driving me nuts... 2004 f150 5.4 ...
View 14 Replies
Starts good cold and hot. Taking off like a grandpa on an evening drive don't notice a thing. Only codes that keep coming up are 2614 and 2617 which are cmp and ckp open curcuit codes and a software incompatibility code for FICM which is due to the updated software in the fresh FICM I installed. HPO pressures are good, has boost, idles smooth, revs nice when in park. New injectors (cause it was running rough especially cold before) and CMP and CKP (because of the above codes and didn't change)and ICP and IPR (last 2 installed because of HPO codes that are gone now with the IPR and ICP). Fuel pressure is 65psi (updated spring). When you step on it while driving it sputters and bucks like it's out of fuel, let off the throttle a bit and it purrs like a kitten. I'm a little stumped. I think it puffs a little white/blue smoke while it bucks.. not much tho. and it comes in little puffs. Took off filler cap and there is almost no blow by.
View 6 Replies
I now have an '01 Mountaineer with AWD and the 5.0. I have a strange vibration that only seems to happen when I accelerate as I get on the highway. I get up to speed and just as I let off on the throttle I get a vibration/shudder from the rear. Almost as if I ran over the rumble strip on the side of the highway. It's a short grrrr, then it goes away.
View 2 Replies
My '99 Passat (1.8t) shakes and jerks violently during acceleration. If the terrain is smooth & flat I don't seem to have a problem. The problem gets pretty extreme during acceleration especially if going uphill. Also, it seems as if it really kicks in when the transmission shifts gears. I have replaced the fuel filter, dump valve, & all 5 mounts to include the front snub mount.
View 13 Replies
My 2005 PT Cruiser Limited 2.4 Turbo bucks under acceleration and had displayed the codes for a bad Map Sensor, Throttle Positioning Sensor, and Oxygen Sensor. I replaced both Oxygen Sensors, Map Sensor and the TPS. Each time I replaced a sensor and took it out for a test drive it ran great. The next day my wife is on her way to work and I am on the phone with her, she accelerates to get on the freeway and the bucking is back. The codes it displays now are P2074, P1697 & P0038. All the previous codes except P0038 disappeared when I disconnected the ground cable for 15 minutes after the repair. I start the car every morning for her and run the heater for 15 minutes as it is in the 30's here in the morning and so I replicate that before I take it on a test drive after completing a repair so the conditions are the same.
View 1 Replies
I recently got a 2wd 1994 150 straight 6 4.9L, It's been a great truck so far. It drove from New Mexico to California with no issues. Just this morning it started stalling and dying when pulling up to stop lights and putting it in reverse. The truck has 172,000 miles and has a new serp belt, alternator, radiator, and starter. It seems to run just fine on the highway and once it's warmed up it doesn't stall as easily. There is an exaust leak.
View 1 Replies
I always feel bad for my Prius when I merge onto a highway or have to floor the accelerator pedal to get across an intersection. I feel like it hurts it or something, I know electric motors are durable though, and gas engines are a bit more finicky.
View 12 Replies
I have a 1997 GMC Sierra extended cab with auto trans and 5.7 engine.When accelerating it bucks like it is underpowered. If I manually downshift to 3rd it runs fine. Once up to speed, I manually shift back to OD and it runs fine.
View 1 Replies
When accelerating quickly with v10 get a noise like that of speed bumps on side of highway(bumpy humming) for a split second and then goes away. No change in performance but just had 2 new rears put on and alignment done.
View 3 Replies
I have an 05 RX330 with about 120K on it. I've had it for about a year - no real issues. The car has a slight rattle coming from the engine compartment on the driver side on acceleration. From what I have been reading, that noise is normal on these cars. What I don't find normal is that it has an intermittent loud growl on quick acceleration from a complete stop. It sounds like the exhaust of a muscle car from the 60s, like Toretto's car in the Fast and the Furious.
It happens like at 2500 RPMs for a few seconds then it goes away. The noise is in the same area. It's driving me nuts. And just like everything, whenever I take it in to the shop to have it checked out - it does not make the noise. So far it has happened twice. Last week and last night. I'm afraid it be the transmission, but no check engine light, no loss of power, and the transmission shifts normal. I'm thinking it's an exhaust leak, but as mentioned before - no check engine light. If there was an exhaust leak I would imagine it would trigger an emissions code.
View 1 Replies
So I was given a 1999 f150 4.6. The transmission was supposedly either new or rebuilt. (I'm going with rebuilt) Driving it for the first time today, I noticed it had very little poor acceleration. When I would get on the gas (to the floor) the rpms would shoot up (3-3.5) but the truck didn't accelerate accordingly. It feels like the power it's getting to the wheels. Driving at highway speed trying to maintain a speed at over 70 the truck wanted to stay at 2500 rpms but if I let off the gas just a touch it would shift up (into overdrive I think) and level out at just below 2000 rpms, but if I accelerated even just barely, it would down shift and go back to 2500. I've also noticed the truck runs 5 mph faster than it reads with stock sized tires. I've check the tans fluid and it is bright red in color and at the appropriate level. I crawled under the truck and noticed the trasfer case mount was wet with fluid (not dripping) and the rear output shaft of the transfer case was also wet. Could this be a transfer case problem?
View 13 Replies
Need some input on miss firing on acceleration on a 2001 Ford SuperCrew F-150 Lariat, 5.4 engine. 200,290 miles.
Have replaced all spark plug boots covers (Sept 2012), number 1 plug (Sept 2012), 3 and 7 plugs replaced, 3 and 7 has heli-coil kits (2011) installed for blown out plugs. New in-take manifold (2010). New gas line filter, air and oil filters (Oct 2012) and oil changes every 3000 to 3500 miles. Have poured 12 oz. fuel injector cleaner in gas take two times with 6 to 7 gallons of fuel in gas tank (last 2 weeks).
Have No check engine light on for service engine but have had an diagnostic scanner analyzer plugged into driver side, in cab outlet, 4 different times to see if I have a bad coil on plug or other problems. No codes show up indicating any problems. The engine idles nicely when at stop lights but does have a slight intermittent miss at times when warmed up and stopped at lights. Engine misses when warmed up on acceleration (when it is under a load and on acceleration).
Had a mechanic tell me he could plug an analyzer into engine but couldn't guarantee he would find anything wrong. This sounded like a little snow in July to me and the mechanic didn't sound optimistic.
View 3 Replies
I've had this truck since 2011. Ran great when I got it. Ive had problems with the calipers and I've replaced both the fronts. I keep up on changing the oil regularly. The manifolds started rusting away a little over a year ago. Not happening... The shaking started recently after I pulled a trailer with 2.5 tons of shingles on 2 separate occasions.
That being said, I can feel a little shaking while idling. It was really only bad between 500 and 2000rpms. After 2000 it almost felt like a turbo and it would accelerate really fast and smooth until the gears switched. I figured i should change the oil. Now the shaking is more violent.
Its a 2000 f150 5.4 v8....
View 9 Replies
I have a 97 f150 with 4.2 4x4 auto. I have a bad miss under acceleration. if i ease on the gas no problems. stomp it and it chugs and pops back thru airbox til it gets to 2500 rpm then clears up. If I shift it manually and keep rpms up its fine till it gets below 2500. I have replaced spark plugs, plug wires, fuel filter, upper and lower intake gaskets, cleaned injectors, new air filter and cleaned o2 and mas sensors. Had vacuum system checked and was told all good.
View 12 Replies
I have a 2001 F150 4x4 5.4l with 105k miles. I started it up today to go to lunch and it made a knocking sound on start up that lasted maybe 20 seconds. So i shut it off and checked oil. All ok. Started it up again and it knocked but not as long as it did previously. I started to drive and higher in the rpm range before the trans shifts it makes the same knocking sound. Left off the pedal it goes away then rev it again it doesn't make the knock till around 2000rpm mark it I remember correctly. It makes the noise in all gears, parked or driving. It runs great, no power loss or misfire. Could it be a spark plug on the verge of blowing out or is it time for a new motor? I am going to look at it more tonight when I get off work.
View 2 Replies
my 97 f150 4.2L keeps stalling on acceleration. It ran fine this morning then my wife put 20 dollars of fuel in it and drove 30 miles to her destination with no problem. on her way back the truck started bucking bogging down and acting like there was a fuel problem but it didn't kill. I checked for codes there were none. I removed the fuel filter on the rail and replaced it with a new one. Now it will idle fine with no miss but if I give it gas it kills.
I checked the codes again there are none. I also checked to make sure there was fuel coming from the tank when I turned the key as well as making sure I heard the fuel pump kick on when I first turned the key.I am leaning towards water in the fuel,i didn't see any trash come out of the old filter, however I am not sure. I have a 175 mile commute to and from work.
View 2 Replies
