Ford F-150 - 1997-2003 :: 1994 - Stalling Between 1st And Reverse - Exhaust Leak
Jan 24, 2017
I recently got a 2wd 1994 150 straight 6 4.9L, It's been a great truck so far. It drove from New Mexico to California with no issues. Just this morning it started stalling and dying when pulling up to stop lights and putting it in reverse. The truck has 172,000 miles and has a new serp belt, alternator, radiator, and starter. It seems to run just fine on the highway and once it's warmed up it doesn't stall as easily. There is an exaust leak.
View 1 Replies
Advertisement
It's been a long time since I have posted here mainly because my truck was wearing a bow tie for awhile. But my wife was nice enough to tell me the Bow Tie wearing truck was making a funny noise on New Years Day (seems a small drum corps took up residence in the oil pan). So anyhow now I am back in a real truck . My new to me 1998 F150 5.4 Liter ran fine until yesterday. It started idling rough and almost stalling at red lights. about halfway home the CEL light came on and is throwing a P0171 code.
So far I have checked for vacuum leaks including all the elbows on the PCV system' tried the spray test with a can of flammable break fluid and a can of starting fluid (man I love the smell of that stuff) could not find a leak. Cleaned the MAF sensor and the K&N air filter (not a fan of these) IAC seems to be working. Only thing I know that is leaking for sure is the driver side exhaust after the cat. But that is the wrong bank if I am correct on which bank is which.
So why only one bank running lean and why does it act like it is only firing on 4 cylinders?
View 14 Replies
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 Replies
2002 f150 7700 with 5.4 triton and 4r100 tranny started chugging under acceleration and now stalls when put in D, 2 or 1. park and neutral are fine and reverse works perfectly.
Now when I put it in drive it chugs and stalls immediately... 1/10 times it will keep running but chug violently like its running out of gas. will get worse and stall if you press the gas. i can light the tires up for a block in reverse however.
Changed coils 1 2 and 3, IAC, bank 1 knock sensor, camshaft position sensor
View 5 Replies
So I think I have possible manifold leak in my exhaust and its because when the engine is super cold, and I do have a straight pipe, but it sounds like a tractor... until it warms up after few minutes, it goes away.
My exhaust manifolds are rusted to crap and stuff is falling off, paint or whatever there was on them.
Now I've looked at bunch of videos on UT to get a better understanding since everyone says the nuts and studs are hard to remove or snap.
Now my question to anyone who's done this in their garage; I've seen bunch of videos where the stud snaps flush, then he takes a nut, puts it over the hole, holds it up with needle pliers and uses a MIG to start welding it... stud to nut... then puts a wrench and off it goes.
Now, I'm not a pro welder or anything so is it possible to by accident weld the stud, nut into the head and then never ever be able to undo or take either one out?? or is the head or whatever made from different material that won't get welded to the nut or the stud??
View 8 Replies
Where the cabin air intake location is? I'm not talking about the air filter.
My 97 F150 has some sort of exhaust leak and it's coming into the cabin when the heat is on. I want to tape up the cabin air intake port but I don't know where it is. On later models, it's on the right passenger side near the cowl of the hood. Where is it on the 97?
View 2 Replies
1999 F150 New 5.4 ~350 miles on it. Longtube Pacesetter Headers with cometic mls gaskets. Stainless bolts.
It is making a knocking sound and I can't tell if it is internal or from the headers. I have a video that I hope you all can tell what is. I tried listening to the block with a yardstick, but I couldn't notice a significant increase in volume but my hearing isn't the best. I made sure all the header bolts were tight, but no change in sound.
YouTube...
View 6 Replies
I just purchased a 2003 V10 with 270 000kms. The truck had had regular maintenance. It has an exhaust leak and runs a little bit rough. Could the exhaust leak cause the truck to run a little rough or am I dealing with another issue?
View 2 Replies
Why my 03 focus zx5 will stall in reverse. I have had the tranny serviced. I can drive it and then let it sit for about an hour and then try to reverse in it and it dies. I have change the mac, tps, iac sensors. I am at a loss for why this is happening. I also changed the pvc hose that runs from the back of the motor to the pvc valve.
View 14 Replies
This just started happening last week. When I put the truck into reverse, the engine lugs down and dies. It' as if the AT is fully engaging reverse gear with no clutching action. If give the truck a bit of pedal, I can put her in reverse and back up without issue. Going forward into Drive has no issues.
View 8 Replies
I have a 94 ranger 4L. I am looking for a more loud exhaust sound in/outside the truck and at idle. I have had a cherry bomb turbo on it and it was ok but not loud enough for my liking. I just picked up a flowmaster 40 2 days ago and it sounds good but again just not loud enough for my taste and kinda a lot more. I was looking for a louder muffler that is not a glasspack and would like to stay under like 80 or so.
I also thought about getting a high flow cat which i think might make some more sound but was not sure. Im running the stock pipe which is 2" and end in back of the wheel on the right. I look at the Hooker Headers Maximum Flow Muffler which i thought would be louder b/c it's more straight through the muffler so it would put off more sound better. What would u recommend for something more loud ?
View 14 Replies
I have been thinking about toying with my exhaust. I don't have a crazy amount of money. I got a 94 F250 with the 5.8 liter 351. Heres what I was thinking. Get rid of everything after the cat, and then run a single 3 inch pipe from the cat to a flowmaster 40 series, and then exit either right before the back tire or right after it.
View 7 Replies
03 Camry. 117,000 miles. 4cyl. Jerks and gives stalling feeling when in reverse, idle at stop lights and during initial acceleration. Feels like it is going to shut off. No major noises. No check engine light on. Car was fine when I bought it 2 months ago, just started this 3 days ago.
View 3 Replies
I have a 2003 f150 2WD crew cab with a 4.6 V8 engine it has 178,000 miles on it. The other day after I started it to leave work it died on me without hesitation almost like the ignition switch was turned off I tried to restart and it would turn over but wouldn't start so I switched the ignition all the way off and it started right up, going down the road it did it again.
If I try to restart without turning the ignition all the way off it won't start but if I turn it all the way off it will start up first try, it has done it a couple times since and its the same way every time, where to start. My check engine light has been on for some time for something else so I don't know if it picked up a code or not I don't have a code reader to see if it has a new code...
View 2 Replies
Our '03 Dodge Grand Caravan has been stalling sometimes in reverse and in first gear when starting to move. This usually only occurs if we hadn't yet driven it that day, or if it has completely cooled.
Put it in reverse and give it a little gas to get out of the spot, turn the wheel, and it stalls.. Park - Restart - Drive, and any attempt to press the gas normally probably results in stalling again. This presents a problem as I get to a stop sign and it stalls while in the middle of an intersection...so there is danger to this problem.
The only way I have found to somewhat thwart the problem is to ever so lightly feather the gas, and I mean I don't even push it, I tap-tap-tap it. This usually results in not stalling, but a slight lunge in acceleration.
There is a check engine light on and the code is for the emissions Evap. solenoid. Does this have anything to do with it? If not, what the heck is going on?!
View 2 Replies
1997 buick lesabre, 4 door, v6. It was having problem stalling out. This weekend a friend and I lifted the car and replaced the fuel filter and fuel pump. Drove great Saturday and Sunday. Today I get in the car, starts up without a hitch. I start heading down my street and realize I am having to push my brake pedal in ALL THE WAY to get it to stop and even then it's slow to stop. So I back up, pull the hood and check the brake fluid. Sure enough, it's low, so I run to Advance, grab some fluid and fill it up the max line and think i'm ok. Start the car up, pump the brakes a few time and notice nothing new. I get out and realize I have a very steady leak in front of the right rear wheel of fluid. It's a steady drip in two places. Is there something I could have done to have caused this. The only line we messed with on Saturday was the emergency brake line and it's clearly working (I tested it).
View 1 Replies
I own a e1999 Ford F350 7.3 4x4 with a Garrett GTP38R turbo. I have been having issues with very little power and pulled an CEL of P0221. I know it's for the APS and have been trying to trouble shoot it as a new APS has not fixed the problem. However, while working on that I just noticed an oil leak appear. I tracked it down and can visibly see it leaking out the top of the passenger side exhaust manifold in two places. It is seeping out the top. Is oil supposed to even be running through here like that?
I recently replaced my up pipes with the newer style bellowed ones. While I had the turbo off I replaced all the o-rings top and bottom and did the EBPV delete on the pedestal. I have been having very little power and cannot the truck over 5-10 MPH and stays at low RPM's so I originally thought it was the leaky up pipes. Those were fixed along with fuel pressure checks which came back good. I then pulled the P0221 code finally. While I had the turbo off I inspected it and it did spin freely and had no side to side play in it.
What was unusual to me was there was a small pooling of oil in the turbo when I took it off. I know the CCV goes through here so some oil is normal. Also, when I was diagnosing the up pipe leak I could see a small amount of oil spraying out the blown donut gasket along with the exhaust gases. I don't think that is normal.
Is there an internal seal in the turbo that can go bad causing oil to spill into my exhaust and possibly leak at the exhaust manifold? Or do I have an internal oil leak from somewhere else?
View 14 Replies
New up pipe and manifold gasket time!
Massive exhaust leak.. Likely the reason for my 5psi boost.
Wish I had the funds for headers but on the up side, no broken bolts!
View 14 Replies
I've recently had problems with my truck running 97 f150 4.2L.The latest episode is it stalling when coming to a stop. It will start right back up, I've checked for codes and found none, I have changed the fuel and air filters and I have tested the fuel pressure.(I have a video of the test however I don't know how to upload it.) Key on engine off it pumps up to 30 immediately on the gauge. key on engine running gauge shows a steady 32. I am really at a loss for what to check next. I really need this truck dependable again ASAP my wife is scared to drive it.
View 11 Replies
my 97 f150 4.2L keeps stalling on acceleration. It ran fine this morning then my wife put 20 dollars of fuel in it and drove 30 miles to her destination with no problem. on her way back the truck started bucking bogging down and acting like there was a fuel problem but it didn't kill. I checked for codes there were none. I removed the fuel filter on the rail and replaced it with a new one. Now it will idle fine with no miss but if I give it gas it kills.
I checked the codes again there are none. I also checked to make sure there was fuel coming from the tank when I turned the key as well as making sure I heard the fuel pump kick on when I first turned the key.I am leaning towards water in the fuel,i didn't see any trash come out of the old filter, however I am not sure. I have a 175 mile commute to and from work.
View 2 Replies
As it says, I have a tick. It's not apparent at idle and increases with engine speed.
Just spent $570 having bellowed up-pipes installed and while a little quieter, the tick is still there. What else tends to go out on these things? Manifold(s) cracked, manifold gasket(s)? It's seen high EGT's quite a bit but not for longer than 20-25 seconds.
View 8 Replies
