Ford - Explorer :: P0128 Code - Coolant Temp Below Thermostat Regulating Temperature
Jan 24, 2016
2009 Ford Explorer, 6 cyl, 4.0L, 74K. Read code w/scanner - "P0128 - Coolant Temp below thermostat regulating temperature". Assuming this is pretty straight forward but was wondering what the most likely culprit is (?thermostat?). Ironically, this code popped about a week ago, I cleared it and actually got my inspection sticker earlier today and then later in the day, the CEL came on again and once again, the P0128 code. The coolant level is perfect so I know there aren't any leaks.
View 5 Replies
Advertisement
I'm getting a P0128 thermostat coolant below temp. Coolant level checks out. Temp sensor seems to work. It climbs to 160 and holds steady. I simultaneously had a thermometer in the top of the radiator. It went from 86 to 160 with with jump from 86 to 135 which corresponded to the temp sensor reading of 135.
I am assuming this is the thermostat opening. So, the level is right. The sensor is working and the thermostat appears to open and close. Why its throwing a code?
View 1 Replies
2002 Camry 4 cyclinder. P0128 code - replaced the thermostat and coolant. P0128 code is now locked in. Lifetd the battery cable, but it is still there when I start the engine - or - it comes comes back immediately when I start the engine. Coolant temperature looks normal on the dashboard gage when I drive the car. What should I do now?
View 3 Replies
I have an engine code of P0128 (low coolant temp etc.) I now think it's because I no longer have an Engine Splash Shield under my engine and the extra air is cooling the engine. I took it off after backing into a snow bank like an idiot. At first I thought it might be that I poured green coolant into the pink coolant because I lost coolant cleaning the throttle body (120,000miles). This mixture supposedly causes clumping and clogs in the system etc. Since then I flushed the coolant system and replaced it with yellow coolant which popular mechanics said was OK. So I'm left with the question of do i change it again to the pink coolant (~$50 compared to ~$15 for yellow coolant, thats why i got the yellow) or do i get an engine splash guard? Or Both?
View 11 Replies
I have unfortunately inherited a 2007 Toyota Camry LE at the passing of an uncle. I recently purchased an Innova 3140 b diagnostic scanner which pulled up several codes. One of which keeps popping back.
P0128 refers to (according to innova).
Coolant Thermostat (Coolant Temp Below Thermostat Regulating Temperature).
I have replaced the coolant temperature sensor but the codes came back after a few days. I cleared it once again and the code reappeared that same day. I have a thermostat on standby ready to install if the fix requires such.
View 8 Replies
2002 ford sport trac.I have been having an ongoing issue that started with the engine cranking but would not turn over until an hour passed. After replacing multiple parts (cam shaft sensor, crankshaft sensor, ignition pack) I am now down to poor fuel economy as the last of the issues (roughly 12 in the city and 15 highway). I was told the issue may be the engine coolant temperature sensor going bad so I decided to replace it. I found this was very difficult due to it being a plug and locking pin design and in a very tight spot in the engine.
I tried to purchase a replacement and the parts store kept trying to insist on selling me a part with threading. I finally found someone that figured out the issue and found the part for the 2001 sport trac had the same plug style with clip that did fit but was shaped a little different on the sensor end which I assume was due to being aftermarket. I noticed that there were two plugs side by side and the one easiest to access was on the left and I was told the one on the right was the sensor that gave the temperature reading to the gauge.
After installing the engine coolant temperature sensor I found the temperature gauge on the dash now will not respond and is sitting below the cold end of the gauge completely off. Is it possible this is because the part was for a 2001? Is the sensor on the left (passenger side) the engine coolant sensor?I would hate to put the old sensor back in just to test if that's the issue due how difficult it was to put that locking pin back on. What to check that could resolve the gauge issue before pulling this sensor back out?
View 3 Replies
I recently had the engine light come up on my Hyundai Elantra 2003. I read the code with my cheap little code reader with the torque lite (free) app on android. It threw the P0128 code which means a faulty thermostat.
Here's the web link to all the details on the code: [URL] ....
I have checked the coolant level and its good. The strength of the coolant is good to -40 Celsius. The engine fan is not running at all. I recently changed the thermostat. I'm leaning towards faulty ECT. The car takes forever to blow hot air too. It has done weird readings in the past with the temperature gauge in the cab.
I just bought a infrared temperature reader of Amazon and want to check the temperature where the water comes out of the engine past the thermostat and compare it to the reading on the torque app readings. I'm thinking it won't match.
View 15 Replies
Temperature gauge quit working after changing the thermostat and coolant.
With the engine off, I disconnected the single wire from the temperature sending unit and switched on the ignition without starting engine. The gauge pointer stayed in at the Cold mark. Using a Jumper wire, I grounded the sending unit wire and the needle on the gauge went to the Hot mark.
I quickly turned off the ignition, and replaced the sending unit with a SW-2328 (F1SZ-10884-A) Temp Sender. Warmed up the engine, but still no reading on the dash gauge.
View 8 Replies
I did an engine swap for a junkyard motor my 4.0 ohv had a very bad rod bearing so I got one from the junkyard with 117,000,or so they say.Anyhow, after its all said and done it runs perfect except the temperature gauge seems to not get as high up on the gauge as before after sufficient driving(it used to run about middle of the gauge) it drops low at idle then goes up and stays up then goes down.it still has good heat, doesn't seem as good as before tho.I changed the thermostat also.
View 8 Replies
After buying and installing the low temp thermostat, fan switch and green top sensor, I'm still encountering boiling in the line and a temp of 3/4 of the way when at idle. My coolant mixture is about 70/30 and unfortunately I had to use a temporary fix of the prestone universal coolant mix due to the dealer being closed and I didn't want to add more water
What would be the disadvantages of running straight g12 coolant? My issue is boiling and I figure the more coolant and less water, the less chance of boiling to occur.
View 24 Replies
I'm having some trouble regulating the cabin temp in my 2002 SC430. It's cold outside here in Atlanta (in the 30's in the morning) and for some reason even when I have the temp set on 66 (not in auto mode) the cabin gets really hot! If I drop it to 65 the AC comes on. It's just weird.
Not sure where the temp sensor is located (will check the manual for that) but having a problem regulating the cabin temp. If put it the auto mode -- it ramps the fan up to high and cooks us all inside the car.
View 14 Replies
I have an '07 Ford Fusion with 94,000 miles. The check engine light came on a couple of days ago, so I took it to a shop to have them pull the codes on it. The code that came up said the coolant was not reaching the proper temperature, and the mechanic told me the thermostat should probably be replaced.Two questions:
1. Should I go ahead and get it done, or wait and see if the check engine light comes back on? I usually only drive the vehicle about 10 miles a day, and it's all city driving.
2. What kind of cost should I be looking at? He said it would be a system flush, replacing the coolant and thermostat (which they would get from a dealer).
View 4 Replies
My '04 Passat 4Motion (station wagon) engine coolant temperature gauge, fuel gauge, and outside temperature display all stopped working in the same time. Interestingly enough, car has 32K miles and just ran out of manufacturer warranty 2 months ago.
What could be happening? Should I be checking fuse box or this may be related to some more serious failure?
View 1 Replies
This weekend my friend and I plan on doing a coolant flush, new Mishimoto thermostat housing with high temp thermostat and install a Mishimoto coolant filter.
Truck currently has some unknown green coolant in it and Im going to replace it with Rotella ELC. I plan on doing a couple hose water flushes then follow with about 5 distilled water flushes. I've been reading about putting some Cascade in on first flush to dissolve any silicate goo that might be in there hanging out. I might give that a try. Im sure I can manage this part from all the stuff I read about doing flushes.
This is the part that looks like a little more work involved than the flush. Doing the thermostat kind of worries me because of the tight area in there to work with the fuel line and the EBP sensor being right there. The current thermostat holds temps around 175-185 under normal driving. I bought the new Mishimoto thermostat housing with the high temp thermostat installed in it when they had their pre sale going on for the housing.
I decided to just go with the whole thing because of all the stuff I read about people having issues with the thermostat not fitting the older housing correctly since Im certain I have the original housing from 2004, like everything else that's still original on my truck. I plan on removing the thermostat before doing the flushes and then installing the new housing and thermostat and coolant filter before I add the ELC.
The coolant filter install looks fairly simple to do so I should be ok with that.
View 11 Replies
2001 3.0 XLT Ranger 2wd 4 door
Okay getting ready to trade in my Truck. So I removed all the extra things I put on there while I was in college, the amp, fog-lights, and analog oil pressure sensor along with their wiring. It was pretty easy minus removing the oil pressure sending unit part.
I had to unplug the MAF to move the intake out of the way while I was repairing a loose vacuum tank. But I forgot to plug it back in when i closed everything up. I started the truck and drive it about a half mile before I was able to pull over and plug it back in. Truck ran and shifted fine after that, but the CEL came on. P0119 Coolant Temp Signal Intermittent. Guy at Autozone said it was Intake Air Temp Sensor intermittent and I could just replace the part, but they were showing a separate part even though it is built into our MAFs.
So now the CEL is on, can get it to go away. Truck is a little jerky every once in a while, like a misfire, when between 50 and 60. Before all this the CEL was off. Now after I cleaned it up and removed some of the superfluous accessories, I get a CEL. I wanted to trade it in this coming weekend without having to take a loss because of the CEL or spend more money to fix it.
View 3 Replies
Few weeks ago I threw a CEL for an engine coolant temp. It went away and came back now as a P3081, I don't recall that being the code before. But from what I understand It is a simple sensor that I can replace myself. Car is running fine and not overheating.. it did however overheat the last time It threw a CEL but that was also stop and go traffic with AC on.
View 8 Replies
I just had my thermostats replaced in my 6.4, and I'm concerned about the regent process. I read that when the P0128 code is thrown, truck will not go into regen. Is this true? How can I manually start the regen process?
View 1 Replies
I was driving today when the CEL came on, I scanned the car which gave me 1 code: P1296.
I googled it and said it is possibly the coolant temp sensor?
The Engine temp was normal at 190' or just below even after quite a bit of driving today.
Would the problem just be the sensor or should I be looking for other problems as well?
The car is a 2002 B5.5 AWM 1.8T Tiptronic.
View 4 Replies
So my check engine light came on in my 04 jetta sw, and when I had the car read, it gave me a code that tracked down to be a bad coolant temp sensor. I bought the replacement part from my local VW dealership, installed it and the check engine light went away. Now about 2 weeks late it came back on, and I am getting a reading of "Coolant temp sensor high voltage". So it goes from needing replaced, then the replacement is running high voltage?
View 3 Replies
Threw a coolant temp sensor code yesterday morning:
16502 - Engine Coolant Temp. Sensor (G62): Signal too high
p0118 - 002 - Lower Limit Exceeded - Intermittent - MIL ON
Does throwing that code once mean I need to replace the CTS immediately or am I safe to clear the code and see if it returns? No code today after a 40 minute drive.
View 3 Replies
The needle has always stuck dead on 190f when it gets up to temp. About a week ago I took the center grill of to paint, I put it back on and the check engine light came on ... code p2433 secondary air pump problem. I figured I had just disturbed something etc. Now the coolant gauge is going up to around 240f during normal driving, the fan stays on for about a minute when I turn off the ignition.
View 16 Replies
