Ford - Explorer :: 2008 V8 - Wheel Slippage When Taking Off From A Stop
Mar 5, 2013
I have a 2008 4wd V8 Ford Explorer Limited. About 9 months ago I had both front wheel bearings replaced. Immediately after they were replaced, I noticed a strange, new symptom. When taking off from a stop (either headed straight or turning), about 10-20% of the time I will get some wheel slippage.
I can feel the gears slipping, I don't think the tires are actually spinning and I'm definitely not flooring it and losing traction due to engine torque. When this slippage occurs, the loss of traction light goes on, and it always goes away in a matter of seconds and then everything is fine.
Once I noticed this happening I took it to the Ford dealership but they couldn't diagnose it since I couldn't mimic the problem with them riding in the car. They said it shouldn't have anything to do with the wheel bearings they replaced, but I think there may be an electrical connection that wasn't re-attached properly??
View 2 Replies
Advertisement
I was told by the dealer it would be over 150 to scan and do a fuel trim on my 02 Explorer, XLT, 4.0, Auto. I can't afford the scan or a garage. I paid 4200 for it and a short time later it starts surging at stop lights then it starts sputtering when idling and taking a while to start. Next it stops accelerating past 2.5k, then works well a bit then stops accelerating past 50 miles an hour. Then it works with an 02 disconnected then starts acting up again. It now either runs normal, wont accelorate past certain ranges, or starts then quits 3 seconds later, unless I unplug the MAF then it runs 15 seconds then stalls. Through all this symptoms come and go. Always banks 1 and 2 lean.
Symptoms
Knock
Rough Idle
Slow Starts
Hesitation
Lag
Stall
Replaced
02 Sensors
Fuel Filter
Injectors
Plugs
Plug Wires
Tested
Maf
TP
Temp Sensor
Cam Sensor
Crank Sensor
All EGR Components
Idle Valve
Coil Pack
For any air leaks.
Fuel pressure 37 or higher
Clean Fuel Pump Strainer
Flow tested pump
Checked air filter
View 9 Replies
This morning I was driving my 08 Lexus RX350 in fresh snow in Boston area. When I applied brake I noticed the wheel slipping/sliding and I heard brake noise (some sort of cracking noise - I don't know how to define that sound :-). It was fresh snow, may be an inch or two and I was driving around 10 miles. I have to pound on the brakes and it took few seconds before it stopped and I narrowly avoid hitting the suv in front of me.
I was driving with all season tires and ECT snow mode was not on during that time. Could that be a problem?
A week back I replaced the rear brake pads (akebono ceramic) & rotors (raybestos) at a local garage. Will it be a problem with the way it is replaced? or will there be any issue with ABS?
View 14 Replies
Looking at a truck at a dealership. 04 F150 Lariat 5.4 3v? 2wd SuperCrew 148k miles. Bone stock besides the bedliner.
Truck is pretty nice besides these 4 things. Kind of a shudder when taking off from a stop or a very slow speed. Adjustable pedals don't work.
New brakes, but possibly the rears are dragging a bit. Was able to turn them in neutral and the rear on jacks. Extra, guessing because of the newer looking battery, some systems lack data from the OBD2
I'm mainly concerned about the shudder from a complete stop/1-2mph. At the dealer, to leave the lot, the driveway was elevated. I think it showed very well climbing that hill. As it was noticed and played with the gas a bit. Otherwise, you stomp the gas, it may shudder for a second or two, (3-5 times?) once it hits about 3000 rpm in 1st, its fine. Only ever seemed to do it in 1st and never any other gear, never on any gear changes.
We lifted the rear end up on a jack and fiddled around. Put it in neutral and spun the wheels, tried to mess with the drive shaft... According to dad, who was looking at it with me said it was fine and that it's normal to have a little bit of slop, but I didn't notice any real slop myself, tried to push on the driveshaft on the transmission side and I think it may have moved a bit but it didn't feel loose or clang or anything. Although I didn't get to push on it too hard because he was rotating the driveshaft at the time.
I assume new fluids in engine and trans. My dad said something about old oil marks on the transmission pan area or something. Both to the fill line.
One thing that I wonder about is how long this truck has been sitting. I wonder about the differential clutches. I'm not that sure what it really has for the rear end. But google had mention of clutch packs in the rear. I wonder if because it's been sitting that the oil has settled out of the clutches or something. There was a mess of silicon on the rear diff cap area. Couldn't tell if it was new or not. I think we put 10-20 miles on it at least and only looked under it for maybe a half hour... Still did the clunk/shudder at a start from a stop, when we returned it.
So, what could be causing this clunk/chatter when talking off from a stop/1-2mph roll?
Axle wrap?
Differential Clutches?
Differential?
Driveshaft?
Transmission?
View 7 Replies
About 8 months and 12k miles ago I had the trans in my 2007 Explorer V6/auto completely rebuilt – now has about 89k. In the last couple of days when pulling away it has intermittently (maybe once a day) sounded like a loud fan was revving, which was accompanied by what I believe is trans slippage. Yesterday it seem to get more regular, at idle it revved itself up to about 2k rpm without moving while I was sitting at a red light, felt like the trans was slipping and then the communication section of the dashboard flashed red with a thermometer. As the warning was red, the engine temp gauge went to hot, as soon as the fan sound and slippage issue stopped (after about 10-15 seconds) the message went away and the engine temps gauge went back down to normal. What may cause this? Also, how long a dealership should warranty a its trans work?
View 3 Replies
The boss has an 08 Sport Trac, V8, 4x4. It has the hard bump when slowing to a stop. I've read here that there is a TSB to reprogram the transmission. Called a dealer in Ft. Worth to schedule appointment. Service guy say there is no TSB. Looking for a copy or number or anything on the TSB?
View 7 Replies
We have already dumped $800 into this problem at the dealership. I should have just come here, to begin with. Here's what happens. When we make a long turn at around 40 mph the engine will cut out and the wheel slippage light comes on. The wheels are not slipping and this only occurs during long slow turns. Very odd... The dealership has no idea and has already ripped me off once.
View 10 Replies
My wifes 2002 explorer stopped taking fuel at the gas station. You can only put about 1/10 of a gallon in before it clicks off. I have already dropped the tank and checked the fill and vent tubes, and looked inside both of the charcoal canisters on top of the tank. Everything looks perfectly fine?
View 14 Replies
2008 F150 5.4L. So today I was sitting at a stop light and Idk why but I just sawed the wheel a little left and a little right and my RPMs fell off. My idle is set around 600rpm and when I turned the wheel it started shuddering really hard and RPMS fell down to about 300RPM. Once I give it the gas it goes away completely....I got it back to my house and it has continued to do the same thing. The engine shudders really bad and the only thing that will sraighten it up is the throttle. Power steering fluid is full.
View 4 Replies
I've had a 1999 explorer for a few months. The transmission has always taken a couple of seconds to "catch" in drive and was then fine. Today, I had to tow another car a short distance and now going into drive directly is useless.
I must shift into 2nd and then back into drive. Then, for the most part, the car drives fine unless I have to put it in Park or in Reverse. Then I must repeat the procedure.
The fluid is fresh and the dipstick shows a slight overfill. Is there anything I can do about this or is this the death of the transmission. If I can run it another couple of years, I'd be satisfied.
View 7 Replies
Finally finished rebuilding my 5R55W transmission and have it back in the 2002 Explorer. Reverse works good, Drive works great, but I am having problems with it wanting to take a long time shifting from 2nd to 3rd. Have to let up on the accelerator in order for it to go into 3rd.
Goes into 3rd hard! 4th gear and 5th gear are finally back. I rebuilt it because I didn't have overdrive. When I didn't have overdrive, it would also take a long time to shift into 3rd and was hard.
Checked codes and am getting a "pending" P0745. Pressure Control Solenoid "A". What I need to start with?
View 3 Replies
I got an 02 explorer xlt with the manual heater control and I've noticed now that it's getting colder it seems like my windshield and side windows are taking forever to clear up when they are foggy. When I put my hand up by the window or the vents for the driver/passenger side windows there's barely any air movement, and that is even when the blower is on the maximum level.
Another thing I've noticed is if I set it to floor only, it blows out the defrost. Same for the defrost only, I can feel some air blowing onto my feet. So what to look for when I pull this into a garage and start to looking around. I also changed the coolant and put in a new thermostat about a month ago, if that's of any importance.
View 5 Replies
2000 f150 4x4 5.4 7700 series. Problem I am having is taking off from a stop sign the engine feels like its not getting any fuel especially when out side temp gets above 90 or some higher, truck runs great other then that ,expected fuel mileage is good,no codes at all, doesn't miss or jump..
View 9 Replies
Wonder if its dry driveshaft slip splines? Only happens when leaving a dead stop under hard acceleration. Hard to describe sound, but seems to be coming from behind me, almost sounds like 2 broken pieces of steel snapping past each other. frame is o.k., leaf springs are o.k. , doesn't do it when shifting between gears or if I gently take off from a stop. I don't think there's a grease fitting for the driveshaft where the splines are (where the 2 piece shaft takes up slack for being loaded or unloaded) may have to take that apart once the weather breaks and see what i find. my 1st ranger never had this issue after 200K miles. this truck is now at 145K but its almost 20 years old. I've read somewhere before about pulling the shaft apart & greasing the splines up. does this sound like a possibility for whats happening? not sure what else it could be.
View 3 Replies
I have a 2000 Expedition that hesitates and sometimes stalls when taking off from a dead stop. The problem is not consistent and therefore hard to diagnose. I have had it to the dealership and two other mechanics and none of them have been able to fix the problem. So far they have replaced the intake gasket, fuel filter, EGR and PCV valves and have changed the PFE sensor and connecting lines. It seems they are just throwing parts at the problem and haven't a clue what is wrong. There are no error codes in the computer.
So far I have spent around $1,500 on this problem and it is not any better from when I started and it might actually be a little worse. I seem to think the problem is in the fuel system and not electrical because all lights and gauges function normally when the problem happens. I can also sometimes produce the hesitation by shifting the transmission into second gear while going around 50 mph then giving it a good bit of throttle after the engine revs. What could be going on.
View 1 Replies
99 F250 7.3 everyday worker, just recently my tranny slipped as I was taking off from a light, I thought hmm that's odd! Pulled away from the next light , it did not slip! Later in the day did it again, so I ran by the transmission shop to have a service done, to my surprise I was told service would not work, and a rebuild was going to be 3200-4k. truck has been used lightly for the last week or so, slips sometimes and not others. I still believe I need to have it serviced? can I do this myself ( I haven't a clue)....
View 7 Replies
a little history here, about 2 years ago I got my first P401 so I changed the egr valve and it went away for a little while. Then I came back several months later and changed it again. along with the P401 I get heavy black smoke when taking off from a dead stop and after it gets a little speed it will run good. Here lately it seems I can only get 2 weeks to a month between cleaning the EGR valve.
Each time I clean it has a bb size piece of carbon stuck and is holding the valve open and there are several more under the EGR valve. each time I try to vacuum the carbon chunks out and clean everything as best I can. As of now I'm fed up with it and would like to do something to make it more reliable. would taking the intake off and cleaning completely and adding a EGR delete kit eliminate the carbon from building up?
View 11 Replies
I went to a couple custom exhaust shops to see about duals for my 04 f150. they gave me a price all were different ranging from 250 to 480 for the same set up. Cat back flow master 44 series dual out the back. I asked them if they can take the cats off and they said no and it would lose performance. is this true? i saw a couple videos on youtube.com and there was some with no cats. I kinda want to get true duals. So is it possible or not for this truck.
View 14 Replies
5.4L 3v engine: The PCV is located in the drivers side valve cover. Tried to pull it out with no success and came to the conclusion that maybe it's threaded and a nut locks it in from the underside of the valve cover. Can this thing be replaced without taking off the valve cover?
View 4 Replies
I've read several posts that suggest the EV mode is mostly useless. I disagree. I've noticed that it's useful in gaining speed faster without the ICE, when taking off from a stop. Especially if I'm in traffic and I don't want to annoy drivers behind me.
I've noticed that conditions have to be met in order to do this, such as engine warmed up etc. but I find it very useful, and I am seeing improved MPG when doing this. I've had my 2013 PRius v Two for almost a month now.
View 3 Replies
I have a 2005 Passat GLS TDI. Recently it has started jerking when shifting and hesitating when taking off from a stop. I guess it's not quite a hesitation but I press the gas and it takes a few seconds to kick in and go. The check engine light came on and I read the codes with a code reader.
The codes I got were P0674-Glow plug/heater cylinder 4 and P0741 Torque converter CKT performance or stuck off. Now The car started hard in the winter when it was really cold so I am assuming the one code means we have a bad glow plug.
View 1 Replies
