Ford - Explorer :: 2006 - Shifting Hard Into Reverse At First Then Stuck In High Gear Or Slipping - OBD2 Codes
Aug 15, 2015
Tranny started acting funny recently...shifting hard into reverse at first, then last night it was like it was stuck in high gear or slipping on the way home. Limped it home and took the following codes:
P0743 TORQUE CONVERTER CIRCUIT ELECTRICAL
P0750 SHIFT SOLENOID A MALFUNCTION
P0755 SHIFT SOLENOID B MALFUNCTION
P0760 SHIFT SOLENOID C MALFUNCTION
P0765 SHIFT SOLENOID D MALFUNCTION
P0962 PRESSURE CONTROL SOLENOID A CONTROL CIRCUIT LOW
P0966 PRESSURE CONTROL SOLENOID B CONTROL CIRCUIT LOW
P0970 PRESSURE CONTROL SOLENOID C CONTROL CIRCTUT LOW
View 1 Replies
Advertisement
I was pulling into my driveway. I put the car in park, but when i went to get out of the car, it started to roll forward. When I finally got it stopped, I tried to shift it, and it wouldn't shift to any spot. Then it became stuck in between Park and Reverse. I can't move the gear shift.
View 1 Replies
We are planning on taking our 07 Explorer in to the dealer to have them check on a couple of issues. 4.0 with auto and about 45,000 miles on the ody.
1. While taking off after waiting at a stop light or slow speed traffic crawling there is a high revving sound coming from the engine compartment. Sounds like the fan is over revving compared to the engine speed.
2. Recently the truck has a hard time going into reverse. Physically hard to move the gear select lever and there is a hard "thunk" when it does actually shift into reverse.
I just want to be armed with information before heading to the dealer. The truck is still under a warranty plan, I just need to be prepared. Could it have to do with the Transmission Range/Position Sensor?
View 2 Replies
I've got a 07 accent with 90k miles on it. It has recently started slipping some (revs high, while in gear, without accelerating, especially in 5th gear). It also can be physically hard to move the shifter into gear sometimes (with my hand).
So, does this mean I need a new clutch? Or are there other possibilities? Should I replace/fix anything with the clutch? Sounds like the flywheel should be resurfaced? Will it shift more smoothly after the fix?
Is this something a newb could do himself? I can change the oil, rotate tires. Outside of that I haven't done much. My toolset for now is fairly limited: two jackstands, a trolley jack, torque-wrench and ratchet sets.
View 12 Replies
I have a 2008 Accent (base model for the most part, no C/C), and my transmission seems to be slipping a bit. The symptoms are: slow acceleration, a delay in gear shifting, and after the 30MPH mark, it takes forever to get up to anything near 60. I just wanted to know if it's a simple solution such as topping off the transmission fluid, or if it's a bigger issue.
View 5 Replies
What can I do about my car it's not shifting, it's stuck in high gear and when I go from park to reverse it makes a loud thump. The check engine light came on and the codes are transmission control module it's a 2006 and only has 30,000 miles on it. It's hard to believe it's the brain so we changed the fluid and cleaned the sylinoids but then when I drove it around the block I put it in reverse it didn't make the loud noise and it shifted fine for a minute before I got around the block and almost home it made a loud banging noise and went back to not shifting again. What the problem could be.
View 5 Replies
My car recently started running overtemp not much, but enough to bother me. I flushed the system with no change. after about a week with continued symptoms, my trans started shifting hard between 1st to 2nd and 2nd to 3rd, and running rough in general, sputtering lightly in high gear. I assumed it was running over temp with the rest of the car, so I replaced the radiator and the radiator cap, yet still am having the same problem. Is it still related to the cooling system? if I replace the water pump will i solve my problems, or is it really a hidden trans problem? I'm fairly certain the trans has never been serviced, and I'm reluctant to do so given the high milage, 174,000. The fluid is full, but its very thin, and no longer red, its sort of a pale yellow.
View 19 Replies
So, I bought an used 2006 Hyundai Azera Limited few days ago. It's clean title and has 86k miles on it now.
After three days from the purchase date, my car starts causing transmission problems, hard shifting from 2nd to 3rd gear only. It's getting worse now...
Now, what should I do? ...
View 1 Replies
Any way, they come to me and tell me the tranny is slipping. I immediately notice the SES light on. I decided to check codes to see if I have any errors coming from the tranny. So far I have these codes: P0455 P1151 P0304 P0174
I dont know this vehicle at all and wanted to see if some of these items are common and/or possibly related to each other.
Heres what I have found:
P0455 - EVAP leak somewhere. Seems a lot of people have discovered a crack in the filler neck.
P1151 - Passenger O2 LEAN
P0304 - Cyl 4 misfire
P0174 - Passenger lean condition "A Heated Exhaust Oxygen (HO2S) sensor indicating lean at the end of a test is trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects switching for a calibrated amount of time."
Looks like I need to clean the MAF, check vacuum leaks, possibly replace passenger O2. Ive also read some of these codes come from a common issue with the intake gasket. May need to replace it? How should I clean the MAF? Can I use some normal solvents?
I need to mention a tick/tap on pass side under cold idle (consistent, but not constant). Still need to test to see if it happens at other times. Right now has Seafoam in the oil and about to run it and then change the oil. Also, have ran it though the brake booster. Currently in the sit and wait process, about to go out and make the neighborhood smoke like Hiroshima.
View 4 Replies
I have a 2006 GS RWD the transmission started acting weird 4 month ago went to many workshops and no codes were found in the computer and my problem is that when i am moving in the car for more than half an hour and stop the car seems hard and jerking while shifting to 2nd gear and if i put it in tiptronic it go to 5th gear immediately it seems ok when the transmission is cold so what do you think it has got 125000 miles on it and what is the normal temperature for the transmission so i can test it with mini vci...
View 7 Replies
From the other users it seems that almost all are having slipping of gears and rough shifting associated with this code. On mine I'm not getting any slipping or rough shifting...it actually still seems to be driving just fine. The OD light came on and will go away after shutting the truck off and back on...it will then not flash anymore for say a couple of months or so...this has been happening for the past few years every now and again and i never thought much of it. I just made a 2k mile trip and this happened again but this time it threw the p0775 code which is a first.. Is it possibly a very early sign of the sensors going bad.
View 3 Replies
2007 Chevy Impala3.5L 6-cyl Flex Fuel engine w/ 4 speed auto trans52,800 miles
Extreme driving conditions maintenance schedule kept.Transmission standard service done @ 32,800 miles which was 20k ago.
PROBLEM:
1) Twice in past three days, when shifting from reverse to drive the transmission has slipped, revving hard with rpms spiked above 3,000 for about 2 seconds before engaging the forward drive gear.
Normally I come to a complete stop of all reverse motion with foot fully on the brake pedal before shifting. Admittedly, I got sloppy the first time noted and still had very slight reverse motion when I shifted.
2) Several times late today, while driving uphill at approx 35 - 45 mph, when the car downshifted there was an extremely brief moment of transmission slippage with spiked rpms. It was so brief each time that at first I thought I'd imagined it until it happened again. Then it did it once on a level surface in a parking lot when having shifted from reverse to drive without problem and was gently accelerating the transmission again slipped for just the briefest moment when the normal automatic shift point was reached. So far, all incidences while driving have been so extremely brief that it was the merest hint of a hiccup.
3) When bringing the car to a complete stop, such as at a stoplight or when parking, as the transmission automatically shifts for the braking of speed, sometimes there is a minor but noticeable thunk sound seeming to come from underneath the car, I'd judge to be somewhere about under the level of the dashboard or slightly forward of that. Could that be from a worn or broken transmission mount? And, if so, could that be somehow causing the slippage problem?
4) This transmission has always, even since new, allowed more roll after being shifted into park, the engine shut off and my foot taken off the brake than any other car I have ever driven. If I forget to engage the parking brake quite tightly, the car will roll forward quite a few inches before the parking pawl holds it, even on the level. I've been told both by the dealership shop and the independent mechanic shop that there is no problem and that this particular engine/transmission combination tends to do this although my particular car seems to do so somewhat worse than average.
ACTIONS TAKEN SO FAR:
1) Have made an appointment to take the car into the mechanic.
2) Will check the transmission fluid level per instructions in the owner's manual tomorrow when I have daylight to see what the fluid level and color on the stick looks like.
NOTE:
1) I periodically check the transmission fluid level and it has never been low or discolored. The shop checked it for me, along with making sure everything else was road trip worthy, for an emergency 1,000 round trip in late November, just three months ago. No problems then.
2) No evidence on the garage floor of any leakage. Garage floor is dry.
QUESTIONS:
1) I presume the first step is for the mechanic to check the fluid level and examine for any leaks?
2) If the mechanic cannot duplicate the problem in a test drive, then what?
3) If the problem cannot be duplicated and no apparent cause found, I presume that the prudent course of action is to go ahead and have standard transmission maintenance done (i.e. drop the pan, check for debris, drain and replace with fresh fluid) then see if that halts the slippages?
4) Given that this car has already had failures of the power steering pump, water pump, and part of the wiring harness, and has a fuel pump starting to get noisy, despite aggressively maintaining all standard/preventive maintenance, that perhaps it is time to think of replacing this car, especially if there proves to be any truly major transmission problem found?
View 19 Replies
The reverse gear in my F150 has started slipping all of a sudden, with no noise or notice. All forwards gears are functioning properly. If I rev up the motor in reverse it seems like it wants to go, but I get the wrench light/safe mode and it now has a P0720 code. I've done some research and replaced the Output Speed Sensor and replaced the tansmission fuild and filter. I cleared the codes once before I changed the sensor, and now my reader indicated the the P0720 is "Pending". Do I have to keep trying to use reverse? Drive it more? Plus it looked like after driving it today that I might have overfilled the transmission.
View 2 Replies
My excursion's trans is slipping on the 25hp tune up high in the RPM band and shutters when up shifting. I have dropped to stock most of the time, but I know i am on borrowed time.
I had a JW trans in my e99, and there is no question on the durability and performance of the transmission. The price has gone up a lot, but that's maybe not the big issue.
I live in the mountains and spend a lot of time pulling and just driving in that 40 to 60 mph range over mountain passes. That is basically where I spend ALL of my time.
The distance between 3rd and 4th is driving me CRAZY! I have researched everything from swapping to a manual, to PCS controllers, to trying 4.11 gears, to overdrive units.
Swapping Manual: ZF6 is the obvious candidate, but I have read the swap is not probably something I have the skills or tools to do. I have also read that the performance of the ZF6 is sub par. But it seems like it would give me my 3.5 gear that I am looking for.
PCS Controller: Looks cool for a way to have control besides using the tree shift. Maybe a compromise on not swapping in a manual.
4.11 Gears: I get pretty excited thinking about the low end torque etc. I go off road almost every week, and like I said, I hardly go over 75 mph. But once in a while I do. Right now, the truck turns about 2300- 2500 rpm at interstate cruising speed. Looking for 4.10s rpm in that range to compare? Also, how bad of a fuel economy hit would I take? What is the cruising rpm of 4.10's between 60 and 65 mph, or in general what is the rpm change?
Overdrive Unit: I have always been interested in more gears, but I read about someone who installed one behind a 7.3 and didn't have they great of results. To the point where he said it wasn't worth it.
View 2 Replies
Like the title says. 04 Explorer.
No transmission issues ever. Immediately after doing an oil change myself for first time, get some transmission dropouts, slipping out of gear at stop lights, waiting way too long to go into 2nd, etc.
Then, started getting OD off light, and service engine. Error codes show something about wrong setting for 2nd, 5th, solenoid error... a bunch of 'em.
Anyway, guy at parts store says I must have knocked a wire loose causing misreads between cpu and transmission. It's a real pain getting under there since I'm using jack stands, so exactly what I should be looking for or at least the exact name of a connector or something so I can look it up.
View 1 Replies
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 Replies
New truck 11000kms ago thats done medium amount of work but nothing heavy or sustained for long periods of time. I get the feeling of clutches slipping especially when truck is cold but also when normal temps. Doesnt make any weird noises or anything. I can really notice the difference in torque if in manual mode being much better, but still not perfect if i stomp on the gas pedal and go through the gears in manual mode will still slip. Also is really harsh shift if i come to a halt in 3rd manual mode with the brake pedal depressed push minus button the truck makes very loud clunk noise into gear 2 then 1. Took it to ford they couldnt find anything ? Thinking of trying another dealer.
View 2 Replies
We have a 2010 Santa Fe AWD LTD with about 140, 000km on it. It recently came back from front suspension work. The suspension is fine now, but we notice harder shifts in the transmission. Also, there seems to be a vibration just before shifting gears and when under load (like going up hill) seems to slip (like on ice) about once every second until the shift is made. Once the shift is made it drive smoothly until put under pressure again. Even stepping down a bit on the accelerator will cause this slipping feeling (or maybe its loss of power). Just had new plugs put in and a tuneup so it's not that. Could something from the suspension work cause these symptoms?
View 29 Replies
In my 1998 f150 4.6L 5 speed manual. When I go to put it in reverse I get 1st instead, but if I do a second shift to reverse I get reverse. This happens on an average of once a week.
I know this can happen in FWD cars where you put it in one gear and get a different gear instead. Something to do with the shifting cable. But the f150 is RWD, the shifting problem only happens in reverse. Is this problem someone without ASE certificates can do, or without dropping the transmission?
I'll add to this so I don't start yet another post. Ive thought of the problem and if it was really going into 1st instead of reverse the problem likely would be bad enough it would just stay in 1st. Its possible that I am getting 4th gear when I go into reverse which tells me the clutch grabs really well, and its a problem I really need to fix, I don't know that much about transmissions but I do know if it keeps getting 4th instead of reverse, the clutch wont be so good pretty fast.
View 1 Replies
I have a 1997 F250 heavy duty 4x4 7.5 efi. I just bought a 2003 weekend worrior weighing 5800lbs dry. When I go up slight hills in 4th gear it seems to work real hard especially on freeways, could my clutch be slipping or am I just at max tow
View 11 Replies
Have a 2000 expedition with 84,000 miles. Tranny seems to shift hard from first to second gear. Its been 24,000 miles since my last dealer tranny service. Thinking of getting a new service now before the recommended 30,000 manual recommendation. Whats happening?
View 6 Replies
