2004 Explorer Eddie Bauer . Bought it like this and trying to figure why. Code is P0740 and P0743. It will go about a mile then go into Limp Mode with the Orange Wrench symbol and will die. If I pull over and restart it will go another mile before doing it again. Any Tips? Trans is 5R55S....
View 2 RepliesI have 2007 explorer 4.0 4x4. Check engine light and wrench symbol on with codes po743 po750 po755 po po765 po966 po966 po970. Feels like it is now stuck in 3rd gear.
View 2 RepliesWife come home the other day after leaving for work with the truck no going past 20KM to 30KM.. After some investigating it seems to be in Limp - In Mode. There was a Check-Engine light & after further investigation found a Vac hose with a leak, repaired this & test drove. Same issue.... then there was a loud hissing sound from the engine area so I investigate & now found the EGR sensor (DPEF pressure sensor ) had blow a hose & fried the sensor.
New sensor was replace along with 2-hoses cleared the engine light but the truck still will not go more then 20KM or 30KM max.. I checked the EGR valve with vac pump & engine stalls or so the valve is good. I have left the neg cable off the batt to try & clear the Limp-In mode without success. Looking for a way to clear the limp-in mode or do I need to clear it with a scan tool?
I was driving home. Problems started after pulling away from a 4-way stop. Truck started lunging almost like I was running out of fuel. Then I got a "Transmission Malfunction" in the in dash display. Followed by limp mode. I checked the Faults when I got home. I have the following:
P0720 - Powertrain - Output speed sensor Circuit
P2106 - Powertrain - Throttle Actuator Control System - Forced Limited Power (From what I understand this is associated with limp mode. Not a root of the problem)
P0713 - Powertrain - Transmission Fluid Temp Sensor Circuit High Input
P0722 - Powertrain - Output Speed Sensor Circuit No Signal
The vehicle has around 192,000 mi. Replaced cam phasers in upper engine roughly 1000 miles ago and replaced all the bearings in the rear differential roughly 100 mi ago. I haven't messed with anything on the transmission. Checked fluid level and color of transmission fluid.
Just fully rebuilt transmissin 4r75 replaced all planet gears clutches etc. Now with it all back together the speedo does not work on truck goes into limp mode. I replaced the vss sensor an no luck
View 8 RepliesI have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
I just got an Egde Evo which I installed and everything looked great. After a few runs, I noticed the ABS light coming on an soon after that my transmission goes to limp mode (the wrench lights up).
I receive the DTC error: P2106 on the Edge Evo.
I have gone back to Factory default, but it keeps coming back, ie. the ABS light lights up and the Trans goes to Forced Limited Power (according to the Evo).
Happened once or twice where I tried to back up a hill and the car went into limp mode. Neither the dealer nor my mechanic could replicate it.
View 5 RepliesGot a 2006 GX throwing a P2445 code and car goes into limp mode. Is this the Air Injection Pump? Where it's located?
View 7 RepliesMy wife started up my 2005 GX470 this morning to go to work and drove maybe a half mile before she noticed a problem. So she turned around and drove it back home in limp mode. She put it in park and got out.
Most of the Warning Lights are on ( VSC OFF, VSC TRAC, Anti Skid, Check Engine etc). I tried moving the shift lever but there was some resistance and some grinding noises. And it now seems to be stuck in neutral.
How to diagnose this myself? We only drive this vehicle in the winter, and it was fine the last time we used it.
I am one of the few that has ADC on my 2004 V10.
Occasionally, 3 times now. I press the ON button and the cruise control does not initialize properly. After a while it will say "Temporarily unavailable" . The problem is that then there is no power any more.
I stop on the hard shoulder of the motorway, engine off, engine on and all is reset, ADC works ok and full power is restored.
I have a 2005 Prius. After driving home from a 95K routine maintenance inspection, the car (with the display indicating 50% in the gas tank) went to limp mode and then stopped entirely and had to be towed back to the dealer. The codes pulled were
P0A0F (Engine failed to start)
P3000 (Battery control system)
B2799 (Immobilizer Malfunction)
P3190 (Poor engine power).
The techs concluded that the car was simply out of gas and the display incorrectly showed I still had gas in the tank due to a broken sender in the tank. They also said they added 1 1/2 gallons, and the car ran fine again.
However, I keep meticulous records of when I get gas, and according to my numbers I had at least 5 gallons left in the tank. Sure enough, the tech topped the tank up, which only took 4 gallons, so clearly my tank was not empty when this happened.
We are having an intermittent issue with car starting up and immediately throwing a CEL, red triangle and going into limp mode. Shutting off the car and restarting it sometimes resolves the issue. I'd love to be able to pull the logs from the car to see what is causing this issue.
View 11 RepliesI have a 2007 Prius and it will be my first car once I get my license. It has a bad traction control computer and is stuck in limp mode. I have a neighbor who has worked on these and will show me how to replace it. Right now I have two questions. I keep coming up with how to disable it not the actual part.
View 1 RepliesMy wife and I are driving our 2005 Prius with 130k miles and have experienced some weirdness with the car while driving. We've got the master warning light (red triangle w/ !), and another yellow (!) warning light, plus the center display shows a red car with an !. I've gathered that it means something possibly with the brake controller, so when I parked I put the e-brake on.
The car was driving fine with these lights on (we were in the middle of Canadian highways and couldn't stop anywhere) except that cruise control would not work.
Eventually, it actually went into limp mode, where we would floor the pedal and the car would barely accelerate. Pulled over, turned it off for a few minutes, then back on and it drove fine, warning lights still on.
I just replaced the driver's front wheel hub, and I can hear the passenger front going bad, so I'm suspicious that this may be related. Just replaced the 12v within the last few months with an Optima.
I was installing a neutral saftey tow light under the dash of my 06 sport trac. I touched one of the two wire to ground and wrench light came on. I checked fuse #18 and it was good. WHAT Did I do?...How do I fix it?
View 10 RepliesIt's the first real rain of the season here in Northern CA and the "wrench" light came on as I was almost to work. I just get new transmission earlier this year, so I REALLY am trying NOT to spend a gazillion more on this car, but... It's our family's main mode of transportation (kids to school/picked up - long trips - daily 30 mile commute), we would like it running.
View 1 RepliesA few days ago my wife's 07' explorer 4.0L, 4wd, 72k miles, had the abs light, traction control light, and a wrench light all come on. By the the time I got to look at it, they were off. Now 3 days later, they have all come back on. To me it seems like a electrical issue or maybe a sensor or something but I wanted to get your thoughts on where to start looking.
View 7 Replies1996 Sport Trac. Cruise control works. Speedometer works for one mile or so mornings only. New sending unit in transfer case. What's up?
View 2 RepliesTurn air conditioner on transmission goes into limp mode??
1999 ranger 2 door 2,5 engine long wheel base,,auto trans.
2wd no power windows no power seats....
I was driving to work and got about 15 kms from home and all of a sudden, the engine lost power and I coasted to a stop, with the engine running rough on 3 or 4 cylinders. No engine light on and I have a Scangauge II and all the gauge readings looked ok. the fuel pressure was 42, but the glycerine in the gauge froze solid in the winter and I didn't think it was right. I stopped the engine and looked for obvious problems like a failed o-ring on the fuel filter, any leaks and found none. tried the engine again and it ran perfect again, drove the remaining 40 kms to work with no problem. It happened again on the way home, no engine light, again, stopped on the side of the road, it would not restart, check the SG for codes and there was none. Then it started again and I drove home fine again.
I picked up a new gauge for the dash I had added, and checked the pressure, it was 48 and steady with the engine running, but I then changed the fuel filters and installed the blue spring kit to the filter housing I was waiting for warmer weather to install. Drove it to work again the next week, it ran perfect, fuel pressure steady at 60. Then I used it yesterday and it lost power again. I could not get it to run properly for quite a few attempted starts, the it was fine again and I drove it home.
I idled it and checked for codes again, none. ICP was 740, FMP was 54, SYC 1, Fuel Pressure 60. While it was idling, it did it again, idle slowed down and all the previous reading stayed the same, fuel delivery did go up though.
Previous work done. (Current Kms = 390000) 180000 kms, new injectors, turbo, EGR cooler, (EGR blocked off as well), ICP sensor and regulator, in dash Fuel Pressure and ICP gauges installed. FICM sent to Swampy's after alternator died and took out FICM and upgraded to 54v.
The SG when I try to clear the codes it says "Not Responding" with the key on or off, so I don't think it will read or clear them. Where to start? I am thinking wiring somewhere...