Ford - Explorer :: 2003 Truck Started And Running Rough - High Temp Low Oil Light Came On
Oct 27, 2014
2003 ford explorer 4.6L. This truck will start and run rough high temp low oil light come on and temp gauge is pegged hot. Oil gauge is fine though, checked oil its fine.
I checked coolant reservoir its ok.
If I shut truck off and restart it will run ok and rev like normal and then all of a sudden go into limp mode and will misfire etc...
What sensor seems to be the main culprit?cht sensor???
View 1 Replies
Advertisement
I have been puzzled to why my truck isn't running right. We were driving down the highway one day and*then all of the sudden it starts running really rough. I changed MAF sensor, plugs and plug wires, oil change, fuel filter and air filter. Still doing the same thing. What this could be? 2003 ford sport trac..
View 11 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
I have a 2001 F150 4.6L auto. This truck suddenly started running rough. Cleared all codes and re-scanned after starting truck. The codes are as follows; P0135, P0155, P0443, P0740, P0743, P0758, P1451, P1460, P1747, and P1760.
My question is; is it normal to have this many DTCs come up at once? Could my PCM be faulty causing this problem? Can you swap a pcm from the same year truck with the same options without reprogramming?
View 2 Replies
Well it finally happened, a couple of weeks ago I was headed to an MX race and my check engine light came on and it started running rough. Long story short a piece of an exhaust valve broke off and went out through the head. Dealer has been great even though I was 300 miles from home and they did get me a rental(small POS SUV). Truck was supposed to be finished this week, but now they are saying the head gasket is on back order and they probably won't have one until the middle of April......... I can't be without my truck that long, but not much I can do. By the way truck is completely stock with just under 20K on it, and I have never had any issues with any of my Ford trucks or Ford diesels, even my old 6.0.
View 7 Replies
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 Replies
I have a 93 Ford Explorer, manual transmission. About a month ago it intermittently started running very rough. I does this wether the weather is rainy or not. The engine has done this when it just started up, cold, and when it's been fully warmed up. I have been able to drive it, but it has been quite a challenge. When running, there is a very noticeable noxious exhaust smell. The check engine light has come on some of the time. When the eec codes were checked it only revealed 522, the car wasn't in park or neutral when running the test.
I have tried clearing and rerunning this test several times, yet 522 still shows up. No other fault codes. Don't know how this would cause engine to perform so bad. The fuel tank has been near full when it happened so I believe the gas to be good/ no water. The engine has a lot of mileage on it, over 200K, so I'm not sure if something inside could be malfunctioning, but don't know how to check. The car will run for days very smoothly before this happens again. I have changed plugs, wires and the pcv valve and it still occurs. It's like the engine is hitting on one cylinder when it happens.
View 14 Replies
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
View 14 Replies
Since our weather has returned to the cold side......my truck has started bucking and hesitating at 45 mph with EOT @ 130 and ECT @ 140. I can gas on it and it will clear up/let off and it would start up again once it gets below 50 mph. Once the deltas reach 150+ it clears up completely. Its never done this until this week. FICM volts are steady @ 48V. What is causing this or what to look for?
View 2 Replies
I have 2007 explorer with the 4.6 V8....
Recently it started running horrible. Rough idle, drives badly, hesitation, etc. Check engine light is on, code P0171. I cannot find a vacuum leak, and i am pretty much at a loss. Before it started running poorly i replaced the thermostat, and flushed the coolant. I am assuming this is a coincidence.
View 1 Replies
I have a 2003 Explorer.... 4wd..... and here's my story.. I had a tire blow out (front driver side) and I took it to a tire chain to get it replaced (it was the closest thing to where it happened and I had to get to work)
After the tire was replaced, the truck started to rumble in the front and seemed like the brake was being pressed while I was driving. I called the chain tire store and told them my truck was not doing this prior to them replacing the tire. They said it was fine because I was riding on a better tread tire and the remaining tires were worn.... (okay..maybe so?)
I drive 80 miles one way to work....the whole way there...rumbling and this 'brake applied' feeling. Worked my shift...drove the 80 miles back home...same thing.
Took truck back to store....they said that it was the Front Drive Shaft had cracked at the Transfer case.... I've asked a few people and they think it's just the ABS still locked because I was traveling a high rate of speed when my tire went out. I think the tire store chain screwed up when they replaced the tire....
View 3 Replies
Sometimes the truck is hard to get started and to keep running, Once it warms up it will run fine. The next time it is started it will start fine but when you are going down the road if I try to accelerate it will start backfiring and not pick up any speed. I am getting a lean code on both banks. I have changed the IAC, the throttle position sensor and mass air flow sensor. 2002 F150 with 6 cyl
View 1 Replies
I have a 1998 F150 4.6 2wd regular cab with 255,000 miles on it. Lately it has had some problems. The first is that it will run really rough when under a load, meaning when I step on the gas. It runs smooth at idle and at cruise but when I step on the accelerator it bogs way down and almost shuts off. I have changed the spark plugs, spark plug wires, coil packs and fuel filter. Now I'm thinking maybe fuel pump?
The other issue is that when the truck is having to work a little harder (i.e. pulling a trailer or running in the summer with the AC on) it will start to run hot. I have changed the thermostat, flushed the coolant, cleaned out the radiator, etc. and it still does it. Could both of my issues be related to a fuel problem??
View 9 Replies
126000kms on 03 explorer 4.6 truck started. Running rough at idle and under load.... Code came up for cyl 8 injector. Replaced injector... problem still there. Switched cop and plug with another cyl and plug.... same code and cycl 8 is definitely not working. Would a generic problem always affect i cylinder. I even checked wire clip on for injector... it appears ok. There is power to injector wire clip.
View 5 Replies
1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
View 2 Replies
The truck I'm working on is a 2003 f550 with a 6.0, and 382000 kilometers. My service truck died on me couple days ago, while running. As I rolled to a stop, I noticed that my temp gauge on the dash dropped to cold. (Truck was hot). Tried starting, and I have a crank, no start situation.
After towing it to my shop at work, I hooked it up to my scanner, and found that the pcm will not communicate with the scanner (otc genisis). I have no injector buzz with key on, wait to start light comes on for an abnormally long time. I have 48.3 volts on the ficm,(4 screw), and haven't been able to find any chafed wires as of yet.
View 1 Replies
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 Replies
My truck started to idle very rough. I pulled the codes and I got po308 and po316. First I changed plug #8, the electrode was nearly gone. I have never seen a plug in worse shape. Replaced that plug and fired it up, it still idled rough and threw the same codes. Next I moved the #8 coil pack to the #1 location and vice-versa, still the rough idle and same codes. Then I moved the #8 injector to the #1 location same results. Finally I tested compression in the #8 cylinder and it read 32psi ( not good) everything else read 150 to 160 psi. Squirted some oil into #8 and no difference in compression.The truck is a 2002 with 184,000 miles, it burns a quart of oil every couple weeks but still is in perfect shape. Should I bite the bullet and invest in a remanufactured engine for 2500.00? I put one in my 97 f 150 a few years ago with no problems.
View 5 Replies
2001 F150 4.6. Just replaced all 4 oxygen sensors and spark plugs. Replaced rubber grommet on brake booster as it was leaking vacuum.
Truck is still running rough hesitating.
Pulled codes came up as PO141 oxygen sensor heater circuit. PO171 passenger side cylinders running lean. Fuel trim outside limits.
View 9 Replies
I have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 Replies
I have a 7.3 that's running rough. Started it the other day it ran alright but started blowing white smoke. Bought a oil and fuel additive i was going to run through it. Came a few days later, it stated up and was real loud and sounding like it was loping. It blew a good amount of white smoke, but it just smelt like real heavy diesel. Now i can only turn it over and it won't start.
View 2 Replies
