I got a 03 sport trac and need to adjust the parking brake on it, needs to be tightened up, does not hold on the slightest incline, cables are not broke they where just never taken care of, its a disc brake with drum in the middle
View 1 RepliesJust need to know how common this brake adjusting lever is? Awhile back I rebuilt my whole brake system and for some unknown reason the DS rear drum brake wants to keep over adjusting. Checked and double checked everything but can't see what would be causing it.
The fix has been to pull the wheel and drum and back off the adjuster but that's getting old. If I had more time and enthusiasm, I'd switch the shoes and hardware side to side to see if the problem follows the hardware. My solution for now is go with manual adjustment and to disable the DS adjuster by cutting off the end of the lever.
Before I hack up a lever I'd like to have a back up in case there is any problem. Not sure if the junkyard will have what I'm looking for and don't see the correct style lever on Rockauto or at my local parts places. My luck is to cut up a part that's hard to find.
It is a 2003 xlt 4.6 auto. sometimes, but not too often, when you shift from park to reverse nothing happens, no go backward.... even if you mash the go pedal. if you shift to drive then back to reverse it works fine. Not predictable enough to show it in failed mode to the mechanic. Is this a common simple fix? would this issue throw a code? (No blinking or idiot lights on dash when it does this) is there something I can tell the tranny guys to look at since it is on my dime? Somthing like a shift solenoid or something...
View 2 RepliesI have a 2010 toyota camry that needs a parking brake adjustment. the car still stops with the transmission even if the parking brake pedal is pressed down. I changes the pads in the back and it seems to be a little better, but it's not as good as other Camry's I've been in. Where to look as far as the adjustments go? and possibly how if it's not the usual method.
View 4 RepliesI have an '03 sport trac with 146k miles on it. Truck is in good shape for the most part, it has been very well kept before i got it. In the last few months i have had the flow master exhaust put in and the k&n intake. I had the vacuum leak problem with the hole in the elbow, which was fixed and discovered after replacing the IAC.
I have had a problem with the vehicle almost but not quite stalling when shifting from drive to park. The first thing i did was check for vac leaks, found none. I did not replace the IAC again only because it is only a few months old. I also replaced the MAF, which did not work either, I was still almost stalling going from D to P. The vehicle shut off while in the drive through at McDonald yesterday. It restarted roughly and i managed to get it to a safe spot. I lifted the hood and felt the radiator main hose was solid feeling, so i drove home and replaced the thermostat. In the process i got coolant all over everything.
The problem I am having now is the truck is just cutting off, both at idle and while driving down the road. It starts right back up and away i go. It is random, the truck is running a ok with no signs of any trouble then the next second it shuts off.
I got a strange one. 03 expl 4x4 xlt, started making a weird sound, almost like a rubbing, or a light grinding, comparable to the sound and seat of the pants feel you would get if say you ran out of good brake lining and were creeping the car forward at half mph while dragging the breaks slightly but (except it is when you are stopped and in P). Break pads are fine, just when you come to a stop and put it in park. lasts for about 1-3 seconds. No tranny slippage or other issues yet, all seems to be working. I don't use 4x4 hardly at all but not in last 6 months since there is no snow. Since it is so short I cannot pop the hood to track it down. Torque converter? Fan clutch?
View 3 RepliesI have a 2003 ford Explorer xlt v8 4.6 with a P2197 code.(02 sensor bank2 sensor1)...
I had code P2195 a few months ago and replaced that 02 sensor but just recently truck threw code P2197 and is now starting to idle surge when I stop at a light or just leave it running in park.
Replaced PCV valve and the hose that goes from pcv valve to IAC also replaced Fuel Filter. Cleaned IAC, Throttle Body and MAF did the old check for vacuum leaks with can of carb cleaner nothing found.
Pulled all coil packs off checked OHMs all read .6,coil boots looked to be in good shape going to replace spark plugs and 02 sensor.
Daughters 03 mountaineer. Have changed the brake light switch, bulbs and checked the only fuse I could find for the brake lights. She can drive it by doing the override under the column but still has no brake lights and is an accident waiting to happen. What else to check? Is there a relay or another fuse I could be missing? I'm lost.
View 8 RepliesA couple times recently, I've been unable to shift my truck out of Park & the brake lights don't work.
After checking the related fuses & finding them to be ok, it all works again.
What might be causing this to happen?
I was wondering if there is any way to easily adjust the parking brake so it bites tighter. I took it to Lexus of Pohanka and they told me that it's normal in a Lexus car to have to press the parking brake all the way to the carpet to get it to engage. I immediately debunked this when I recieved a loaner and engaged the parking brake and it grabs a lot sooner.
View 6 Replieshaving problem w/ 98 f-150. first truck stuck in park. figured out how to get around that (turn key 1 position, shift to neutral, start vehicle, then engage transmission). but no brake lights! I have turn signals, driving lights, hazards, etc in rear. I disconnected harness from brake light switch. there are 2 leads, 1 hot, 1 not. i jumped them and no brake lights. i tested the switch and it functions properly (it's reconnected now). i changed my bulbs in tail lights. I unplugged the solenoid (which is impossibly located behind/beside steering column). this allowed me to shift like an old truck (without having to brake first), but doesn't solve my lack of brake lights (i've reattached the solenoid harness to remind me of my problems).
i am putting my money on a broken wire somewhere between the brake light switch (b/c that was good) and the solenoid (i am not hearing that faint click when i step on brake). but a broken wire should work by accident some of the time (unless cut cleanly and completely). there is a green wire with red stripe leaving the brake light switch and 3 wires at the solenoid harness (1 green and maybe a smaller gauge than those at the switch and 2 others which i don't recall their colors). Ford service manager doesn't think it's the solenoid but wasn't otherwise useful except to say, "hey, why don't you bring it in to me." What to look for before i plunk down for someone to perform what I already have before completing the job!
can i splice a wire from something (? brake light switch?) to something (?wire in solenoid harness?) or does that "electronic signal" get processed somewhere else first?
I am in desperate need of a brake light switch for my 2003 Ford Explorer XLT..I have find a dozen but none seem to look like they fit. The current one is a 2 prong Pollak part. I have only seen 4 or 5 prong. The most popular switch that comes up is the motorcraft parts..Doesn't fit!!!
View 14 RepliesThe 2003 Ex. Made it back home last week after a couple years at college. .. registration sticker expired last June! Drivers side mirror "taped" on. Rear bumper cover torn in half w/ a few screws holding it on.
Busted out foglight & small tear in bumper cover above it.
Brake light on - noticed fluid low & cap not seated correctly. One of the tabs that hold the cap in place is broken... new reservoir under $20 at rockauto. Looking for a write up or better to replace entire master cylinder?
I have a 2003 Passat GLX 4Motion that was fine Monday...Having heavy rain Monday and with brake pedal depressed unable to get out of park..I have brake lights but when I got into car and started it I have airbag light and esp light on as well as check engine light...Is there a way to by pass the shift lock solenoid so I can move car into my garage...
I cleaned connections as was suggested and had a tough time as Bentley Manual states to remove console one must put lever into 3 which as lever is stuck in PARK was impossible...I tried pulling out the shift knob button as described and when I still couldn't get any response found that when I pushed the button back in that I was finally able to get shift lever to respond and finally come out of park...
I now get code for no TCM Signal P1626 No Powertrain Data Bus Signal Missing Message from TCM which now triggers ABS , Airbag ,ESP , and Check Engine light all with the cause no TCM Signal .... Now wondering if any easy way to test for data bus signal ?
My wife's 2003 sportrac has developed a problem. The left rear turn signal brake light will not work. The tail light does. When you turn on the left turn signal the front bulb and the dash light flashes real fast. I have changed both, the front and rear bulbs with no luck. I've read on here about the tilt steering column deal. I have moved the steering column while operating the turn signal with no change.
View 4 Replies2003 Ford Explorer Sport Trac XLT v6 4.0 with 89k.
Lately my truck has been acting funny. About 1 out of 3 times I start my truck and put it n reverse it starts doing what I would describe as a hesitation. If I sit for about 10 seconds, it will stop. But if I move while it is happening it will move and jerk as if i was slightly hitting the brake constantly (no the parking break is not on). It will continue when I throw it in drive until I give it some gas. From then on as far as I can tell there are no problems. It doesn't do it every time. I went in for an oil change and they told me I will need to replace the belt soon, so could that be the culprit?
I was pulling into my driveway. I put the car in park, but when i went to get out of the car, it started to roll forward. When I finally got it stopped, I tried to shift it, and it wouldn't shift to any spot. Then it became stuck in between Park and Reverse. I can't move the gear shift.
View 1 RepliesWhen putting vehicle into park, every so often it will barely enage or not at all. Can hear a clanking noise when rolling back or forward. Trans position sensor?
View 1 RepliesThe truck in my sig. makes a clicking noise when it's in the park and I press the brake pedal down. The click is coming from somewhere up high in the steering column. It doesn't make the clicking noise in any other gear only in park. Might be normal but I don't remember hearing it before?
View 9 RepliesMy truck starts right up, then immediately almost stalls or stalls completely. It also shakes a little when idling while its in Park. I just recently had my egr valve, pcv valve, spark plugs&wires, and fuel filter replaced. it has 104,000 miles on it. What could be causing it to do this?
View 9 RepliesI bought a 2010 V8 Explorer on Monday and aside from the apparent "known issue" with the hard 2-1 shift (which I'm trying to get it to "unlearn" by driving differently), it's a really nice truck.
When I shift into reverse it says "Park Aid On/Off" in the display, and sure enough, it beeps when I get close to something. That said, there aren't the normal "dots" in the bumper that I normally associate with backup sensors.
Everything works just fine with it, I just am a guy who likes to know how things work and I don't see anything on the outside that would indicate it's a parking sensor.