I have a 2003 Explorer, I went to use the 4X4 the other day and the light comes on when I switch it 4H or 4L but nothing else happens. So I am thinking it might be the 4X4 mod. How can I test it?
View 1 RepliesSo my Push Button 4 wheel drive wont engage. The light on the dash wont light up and it doesn't shift into 4x4. Where to start? I would like to check the simple stuff first. O and my heat only gets hot when im giving the vehicle gas. This is all on a 2003 Ford Explorer.
View 2 RepliesMy new-to-me Explorer appears to switch to 4WD high but refuses to engage 4WD low. And now I have the 6-times-flashing 4WD and 4WD low dash lights when turning the ignition on.
I used the correct procedure: Stop the car, put it in neutral, and switch to 4WD low. Nothing happens.
I looked for a ground wire from the top of the transfer case to the chassis. I can't find any such wire. All the under-hood fuses are intact.
In the process of looking for the ground wire I discovered a capped 3/8 inch or so vacuum hose about 6 inches long with a right angle fitting at the front of the transfer case. I also found a capped 2-foot-long hose of similar size connected to the top of the front differential. What the heck are these hoses? Has somebody intentionally disabled the 4WD?
I am reasonably adept at electrical repairs, troubleshooting, and modifications..
I have a 2004 Explorer 4.0 4x4 with 130,00 miles that started with the transmission periodically going into neutral while driving and sometimes while stopped at an intersection. Engine running, but no reverse or drive gear. After shutting down engine and restarting, I can drive again only to have it happen soon again. I have changed rear speed sensor, throttle position sensor, dropped the tranny pan and changed the ATF as well as tranny filter.
I also attempted to replace the transmission range sensor but was unable to remove the nut that holds the shift level onto the sensor. Sent 5 hours one day.... nut will not budge. Now the shifter inside the truck does not feel the same when shifting through the gears. Now the transmission will only engage in reverse but the truck will not move. If I wait 30 sec or so the truck will move in reverse. No engagement in drive, 3rd, 2nd, or 1st.
My wife has a 2008 Eddie Bauer 4x4 explorer and when you are backing up or pulling forward with the wheel turned, it feels like the automatic 4wd wants to engage. The Ford dealership mechanic told me this is normal but it does not do it all the time. Is there anything I can look at to try and figure out why this does it sometimes or if this is even supposed to do this at all?
View 7 RepliesWhen putting vehicle into park, every so often it will barely enage or not at all. Can hear a clanking noise when rolling back or forward. Trans position sensor?
View 1 RepliesI have a Ford Explorer that my mechanic says needs a new trany. The vehicle takes a while to engage in reverse and does so with a loud clunk. Otherwise it runs good. I have 198K mi. It's an "02 4wd. Their asking $2,100 for the rebuilt trans. Wondering if it's worth it? May have reached the end of the line on this vehicle?
View 1 RepliesI have a 2000 Ford Explorer XLT. V6, 4x4
At very low speeds (5-10 mph), attempting to accelerate while turning (like coming out of a parking lot OR out of a curve) the transmission fails to engage. I hit the gas, the RPMs go up, but it doesn't get into gear. I will let off the gas, give it a couple seconds, hit the gas again and usually it engages. Sometimes I will have to repeat this step a second time. This problem started very slowly and has gradually gotten worse. It happens about once a day.
Concerned, I took it to the local Ford dealership and they have thus far changed/flushed the transmission fluid and replaced the filter. The mechanic said he found no metal shavings in the fluid, which might indicate grinding gears. They also said there were no codes coming up pointing to a transmission problem. It is still having the same exact issue however. The trouble now is they cannot "verify" the problem. The mechanics have put 40+ miles on it in similar driving scenarios and it will not act up for them.
After a couple weeks of back-and-forth, I'm really frustrated. My understanding is that they're "not sure" it is a transmission problem. They don't really want to open up the transmission case until they have a place to start. It should either be something mechanical with the transmission or a problem with the computer that controls the transmission, right? After getting off the phone with the mechanic today he said it might be a sticky throttle body?
I got myself a 1997 explorer Australian model when I got it (here's the problem) if you put it in drive it will not engage but if put in first will drive normal then shift into second all good now u have push O.D then shift into drive all good (unless u slow down to almost a stop) ? New problem is, it has gone and lost reverse, put it in reverse and it engages with a small clank (normal) but just slips with any revs. I have read posts here talking about upper and lower valve body gaskets and transgo shiftkit which I have ordered but do there maybe more parts needed? Cause it's going to cost me lot just to put transmission fluid back in.
View 4 RepliesI have a 03 4x4 5.4lt supcab with 154k miles. I replaced the shift motor about 40,000 ago but it has always been tempormental like I had to engage it in 4lo in N and then shift to 4hi to keep it in 4hi. Now fast forward to today. Went to shift to 4lo in N and it didn't shift. I only heard the relays click once and then it wouldn't shift into any gear even though the indicator was on PRND123. Didn't matter.
Also, Park didn't engage and the speedometer acted like it was engaged in RN and D. No movement what so ever. I think it might be the shift motor that shifted part way and is stuck in between gears. Is this possible? I drove fine to the dirt road and I haven't had problems other then the shift motor being touchy. I don't want to pay for a new tranny if it might be the shift motor.
I have a 2003 F150 5.4liter 4x4 and when it is cold I can not get the 4x4 to engage. It is a manual shift for the transfer case not electronic. It shifts but does not activate the 4x4 when it is cold. The 4x4 does work when the temp is about 30 degrees or better. Where to start?
View 1 RepliesI've got a problem with my 4x4 not engaging. I've been ready and re-reading all the related posts and threads and am still confused. Here goes. Early in the fall I had no problem shifting in or out of 4wd. Then when it got well below freezing up here, it stopped working. I had it in a warm shop and all of a sudden it worked fine. After sitting outside again it wouldn't work.
When it was warm, I had no problem shifting in and out of 4x4, dash lights functioning as normal. As it got colder it only seemed to work if I really pulled quite hard on the stick and the 4Low indicator didn't work but 4Low was obviously engaged. Now after another day or two outside, nothing happens at all. When the diff does engage, shifting out of 4x4 is never a problem.
Transfer case seems fine as the front drive shaft turns when I shift into 4H and drive forward. After researching a bit, I crawled under and pulled the blue line off the actuator and had someone shift into 4H, I couldn't feel any vacuum so figured it must be the engage solenoid especially since, shifting out of 4x4 is never a problem.
My question now is, shouldn't the lights on the dash be on even if the solenoid isn't working? I am now starting to wonder if its the sensor switch on the transfer case but I don't see how freezing should affect the switch and would think I'd have issues shifting out of 4x4 as well as in. If I put it in 4X4 and test for current at the solenoid and it is there, can I assume that the switch is fine and the problem is in fact the solenoid?
Ok, have a 2003 fx4 auto trans with manual 4x4 ...I notice more and more that say at intersections, when I start out either turning left or right it feels like the 4x4 is slightly trying to engage, or a chuttering feeling..best that I can describe it. any thoughts, I have 106 K and do need to change out the diffential oils etc.
View 9 RepliesI have a 98 f150 4wd with manual shift on floor (msof) and the 4wd will not engage. I've done research and I've learned quite a bit but still have an issue. In All the research I've done I have learned about
View 3 Replies1999 F-150 Sport 4x4
So the deal is I had to use a slim jim to open up my truck door the other day. Door still locks/unlocks fine, only not with the key. Key will still fit & turn the barrel without any prob. just doesn't engage the lock. Took the door panel off and it looks as if the Rod that connects the inside of the key barrel to the lower (part)? not familiar w/name. has come loose.
Looking for a diagram/picture of how it should look to get everything put back together so the key'll work again. Sucks unlocking passenger side and climbing over to open driver door.
Just tried to engage my 4x4 today to see if it was working and nothing. It is the electronic shift on the fly. I started checking the vacuum hoses and found one that looked like a mouse chewed threw part of it and repaired that line. Still no 4x4. So...there are no lights coming on, no sound from the transfer case shift motor and no noise of any kind when cycling the shift ....
I pulled the connection apart at the shift motor to test for voltage with 2hi and truck running and no 12volt. I tested all the pins but not sure if i did it correctly. Also the shift motor itself is rusty on the outside casing. What pin to test for voltage?
I have a 2003 that won't engage all the time. I have manual locking hubs.
View 14 RepliesI have 1999, F150 5.4L with electric 4wd shift. I put it in 4high just fine and smooth. Now 4lo on other hand rough shift if it goes in 4lo, sometimes won't engage but 4 high works fine. What's the cause
View 2 RepliesI recently bought a 1997 f150 4x4 with shift on the fly. I bought the truck from an old man who parked it outside his house. I love the truck, but the 4x4 has been finiky. I have done a ton of research and i have done a bunch of testing. The vacuum system is working correctly. I have tested the solenoids and the front axle actuator is working properly.
There is some kind of electrical issue. It might be the GEM (i really hope not), but it might be the shift on fly switch itself.
The 4x4 will engage, but when i turn the switch to 2h nothing seems to happen. Driving in reverse doesn't work. But sometimes it switch from 4h to 2h, just by turning the truck off and restarting it. If restarting doesn't work, then i have to pull the 5 fuse, let it sit, then put it back in. I read that this resets the GEM. (Number 5 fuse, middle row, 5th from the top).
Resetting the GEM usually does it, but not all the time. Sometimes it will still be in 4x4 again after resetting the gem. And then what is really weird, after driving it in 2h (after the gem reset) then turned it off and restarting it, it will go back into 4x4. All this happens with the switch set to 2h. So I have been having to reset the GEM, each time i restart it. (This was going on for a day or so.)
Any easy testing i can do? Do you think it could be the switch on the dash, or more likely to be the gem? I hope it isn't the gem. I don't want to have to pull a fuse each time to drive my truck.
I just bought a 2000 f150 4x4 ex cab with the 5.4. Once in a while when starting, there is a grinding and the starter won't engage the flywheel. The truck has only had 17000 miles put on it in the past 4 years, and has sat quite a bit. Could the starter gear be gummed up and not engaging all the way, or should the starter be replaced? Or could poor contact on the cables cause this? Or is this a flywheel issue?
View 14 Replies2000 F 150, 4.2 v6, M5OD-2 Manual Transmission, LX, reg cab .. Cruise Control passed all static and dynamic self test. All fuses inside and under hood checked good and still cruse control will not engage. All other functions work: brake lights, turn signals, etc. Green cruise light is operational, checked pin #10 on wiring harness at servo,amplifier unit under hood and have good ground. The Cruise ON button will not turn on cruise control system and will not light green cruse light.
View 4 Replies