Ford - Explorer :: 2003 4.6 - Low Idle / Stalling - Code For DPFE Pops Up
Jul 31, 2012
2003 Limited with 4.6, 89K miles. Just started doing this last night. Checked codes, had the DPFE one pop up. Replaced that, no luck. Cleaned the IAC, MAF, throttle body, EGR, PCV, no luck. Used carb cleaner and sprayed around intake & vacuum hoses, no luck there. Checked vacuum, steady 20in even when it lopes. Battery unhooked for 15 minutes. It hovers around 300-400rpm's, sometimes will stall but drives fine. Tested the IAC and it is functioning normally. Nothing above has worked.
View 2 Replies
Advertisement
Bought a used 2003 Explorer 4X4 that runs like crap.... All I know is it has new upper and lower radiator hoses, new battery, new brakes, 2 new tires and new belts... suspension seems great and body is nice too. It obviously needed a new radiator and complete exhaust, so I did those. Now it is running better ( I can actually get the RPMs over 1500) but still running rough and will stall if I let off the gas. It will surge and dip in RPMs. Very suspicious of vacuum leak.
Unplugged the MAFS and it roared upon start but within a minute started the sputtering etc. Currently pulled the IAC and check continuity between pins and it was 10 ohms so that passed but there is no continuity between either pin and the case. So this seems to indicate I need to replace the IAC which I will do tomorrow. I would love to find a diagram that displays the vacuum system so I can make a thorough check of it. Also seems to have an oil leak on drivers side valve cover gasket.
View 14 Replies
I have a p0401 generic exhaust gas recirculation flow insufficant detected code on my truck I was wondering what would be the first thing to check to get ride of this code? my truck hesitates from a stop while excelerating to several thousand rpm. should I try replacing the dpfe sensor? what does dpfe stand for? do they sell this sensor at oreilys or do you half to get this a the dealership?
View 9 Replies
I have a 2003 ford Explorer xlt v8 4.6 with a P2197 code.(02 sensor bank2 sensor1)...
I had code P2195 a few months ago and replaced that 02 sensor but just recently truck threw code P2197 and is now starting to idle surge when I stop at a light or just leave it running in park.
Replaced PCV valve and the hose that goes from pcv valve to IAC also replaced Fuel Filter. Cleaned IAC, Throttle Body and MAF did the old check for vacuum leaks with can of carb cleaner nothing found.
Pulled all coil packs off checked OHMs all read .6,coil boots looked to be in good shape going to replace spark plugs and 02 sensor.
View 1 Replies
I'm a diesel mechanic and know my way around Powerstrokes, this 4.0 is not what I would usually work on, but I have a friend who has 2006 explorer 4.0L SOHC, someone told him he needed a motor with out explanation why, so I didn't want to see him get ripped off. The problem is it idles very rough, hard to start, and stalls. There's no DTCs , if you hold the accelerator slightly it will stay running, but once you let off it will either idle really bad and misfire or cut off, once pushing the accelerator the rpms raise very smoothly up til 3500 which is what I assume the rev limit is in nuetral.
I've done checks with focom and forscan, I was thinking possibly a bad fuel pump, while monitoring fuel pressure I see a range of 289 - 326 kpa with 26% fuel pump I guess duty cycle would be the correct term(once again I'm a diesel guy, and use to dealing with IPRs and Hpops) not sure if the desired fuel pressure is relevant on these but it always stays at 269kpa. I believe that equals out to 40-48psi while I believe this system is supposed to have somewhere in the range of 60 - 70, but I wouldn't expect to get a rough idle with no load with almost 50 psi of fuel pressure.
So with no DTCs Im baffled, and don't want to start wasting money just throwing parts at it. I've thought everything from fuel pressure sensor, to coil pack(replaced 4 months ago) to crank and cam sensors.
I did end up getting a code p106, but I believe this is because I didnt tighten the intake hose after checking the throttle bottle, I just slid it back on. out of the 4 days of testing first time I seen a code pop up besides unplugging some sensors here and there to make sure the pcm would actually register a dtc.
View 3 Replies
I have 2003 f250 7.3 automatic 181,000 miles completely stock. Never had chip,tuner or anything on it. I am second owner and got it when it had 70,000 miles on it. Ok here we go I live on top of a mountain and soon as i start up the mountain or any steep hill, or pull or tow something my service engine light pops on. First time it came on I took it to diesel shop they hooked it up to scanner and said it was code p1211 said icp sensor was bad so they put new one on. Couple days later light started popping back on so i decided to order a auto ingenuity after doing some research.
Hooked up to truck started up mountain while scanning at wot light pops on code p1211 and think it was live data I remember seeing icp pressure at 1922 and duty cycle at 63% i was trying to drive and read it at same time and my lap top went dead. What does this reading mean 1922 pressure/ at 63% cycle done little research but dont really understand. Year and half ago replaced all orings on all injectors, new rebuilt hpop pump. New ipr valve, glow plugs, past month 2 different icp sensor new,and new ipr valve new pig tails on both and light still popping on.
View 4 Replies
I just bought a '98 Ranger 2.5l 2wd. After driving it for a week or so I got a P1405 Code. After a quick google search I got :
P1405 Ford - DPFE Sensor Circuit Upstream Hose
Possible Causes: - Faulty Differential Pressure Feedback Electronic (DPFE) sensor (EGR pressure sensor)
- Plugged or damaged EGR tube
- Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
- Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection
Now, I have done my research between forums and youtube and have found this EGR system to be quite. I've gone ahead and replaced my DPEF. I took an air hose and blew out all the small lines coming into the DPEF. I still have the engine light. My next move is to get a volt meter and see if I'm getting power to the sensor.
My question is about this particular code and is it possible I need to look farther into this EGR system (EGR Valve, EGR Hose, etc.)
View 5 Replies
I have a 2000 ford f 150 4x4. I just had to replace the engine in it because something got in my engine and beat it up and bent a valve. I replace the engine with one out of a 99 f 150. By the way it's a 5.4 triton. The engine I installed was suppose to have around 77,000 miles on it. I noticed when I got it that the dpfe sensor was melted off of it and so was the hose on one side. I never had that problem with the original engine. I took the dpfe sensor off the destroyed engine and put it on the used one I installed.
Low and behold in less that one day it melted off that one. I have read on here about cats being clogged and or the egr tube. I had no problem with my original engine so it's hard for me to believe the cats or clogged. I did happen to find a metal dpfe sensor off another truck and have installed. I am getting a rough idle now and not sure whats going on. I tried cleaning the egr tube the best I could without taking it off. Also the egr ports on the throttle body are cleaned and open and the egr valve itself is a new one.
View 8 Replies
I just recently pulled the P1401 code on my truck and need to get the sensor fixed before my next emissions test. I called the dealer and they told for the new sensor.
View 14 Replies
Trying to get my daughters Santa Fe going. Engine stalling. Idles very slow. 2001 model with 2.4 engine, auto trans.
Code P0102 is active. Cleared with scan tool and it comes right back.
Replaced the MAF and no change.
Checked the intake for leaks / vacuum leaks and none found.
Checked for debris up-stream from MAF and all is clear.
Air filter is clean and dry.
Checked harness plug and found the pin 5 has 4.6 volts on it from PCM. This is the signal wire from MAF to PCM. 4.6 volts is KOEO.
IS THIS NORMAL OR IS PCM BAD ??? All other pins / voltages on harness plug are normal.
View 4 Replies
My 2003 ranger xlt 4.0 has a stalling problem. The engine light came on in aug and I had it coded at AutoZ and there was a code for the oxy sensor, changed that and didn't work so I took it back. In oct I had it coded and it said the air int temp sensor which i was informed was part of the mas airflow sensor, changed that the beginning of nov, got the computer to reset and it still didn't fix it.
Took that part back and had it coded again a few days later and several codes came up AutoZ code 1732 and the the OEM number to cross for them were: P2195 , P0300 , P0316 , P0174 , P0171 , P2197 . Reset the comp yesterday and as soon as the light came on had them code it again and it came up AutoZ code 1732 OEM # to cross P2195. I guess my next step will be to take it to the dealers to get diagnosed..
View 4 Replies
A couple weeks ago my 01 7.3 with 265,xxx started ideling rough and stalling. I had driven in all day Sunday and the next day it started out of the blue! It would barely start idle rough and stall out no CEL. I have singed changed the icp, fuel filter and I have checked oil level. Also used fuel cleaner. Still had no luck. When I changed the icp sensor the check engine light came on and was no change I then got a ford oem camshaft sensor and my truck fired right up but still sounded like it had a little miss here and there drove it for a few weeks fine now back to the same thing it will start up and idle fine for 10 seconds then start the rough idle but won't stall out anymore just idle rough. I am stumped I can't get any codes to pull up and if oriellys uses there scan tool while the truck was running it would shut the truck off! I can't find any answers.
View 8 Replies
At 65 mph, egt was running between 1050-1150, turbo at 13-14 psi, rpm 2300. Code p0299 pops up. Before this the turbo would spool up to 28 psi going up hills. After it would not go over 16 and sounded funny. Truck is a 2005 excursion 4x4 with just under 200k miles . Trailer is about 10k pounds. No tuner. What do I need to be looking into? Is this too much for the truck to handle?
View 8 Replies
Truck has been driving great for a long time and this afternoon after driving fine to work just died 3-4 times while trying to accelerate from idle. Engine restarts easily but the power is soft off idle, the injectors sound noisier and then quiet down and will accelerate decently once rolling but something is off I can tell.
Fuel pressure is read post filter and is good. Truck is well maintained with all the basics replaced in the last couple years. Could this be CPS going out even if it is only a couple years old? IPR is new in the last year, ICP sensor isn't leaking. Most recent change was a full tank of fuel yesterday afternoon and on a whim performing a boost leak check which was all good.
View 6 Replies
The 2003 F250 5.4 Superduty has no power and keeps stalling. If I floor the gas it just stalls. I've replaced the pcv valve and line, the fuel pump relay, the fuel pump, and cleaned the tank, changed out the gas, added Lucas, and it just won't run right. Desperate, and no codes are coming up...
View 5 Replies
It's been a long time since I have posted here mainly because my truck was wearing a bow tie for awhile. But my wife was nice enough to tell me the Bow Tie wearing truck was making a funny noise on New Years Day (seems a small drum corps took up residence in the oil pan). So anyhow now I am back in a real truck . My new to me 1998 F150 5.4 Liter ran fine until yesterday. It started idling rough and almost stalling at red lights. about halfway home the CEL light came on and is throwing a P0171 code.
So far I have checked for vacuum leaks including all the elbows on the PCV system' tried the spray test with a can of flammable break fluid and a can of starting fluid (man I love the smell of that stuff) could not find a leak. Cleaned the MAF sensor and the K&N air filter (not a fan of these) IAC seems to be working. Only thing I know that is leaking for sure is the driver side exhaust after the cat. But that is the wrong bank if I am correct on which bank is which.
So why only one bank running lean and why does it act like it is only firing on 4 cylinders?
View 14 Replies
My car wouldn't start earlier this week. After jumping it, it stalled out at the first stop sign. I got a new battery and it started great but it still stalled out while idling and low rpms. I gave it a tune up in hopes that it was a bad spark plug or wiring issue. It is running better but it still gets really choppy at stops or idling at a light and it still wants to or has stalled. I had disconnected the negative charge from the battery to check if it was an alternator issue but it ran fine without the battery.
View 2 Replies
I have 2007 explorer with the 4.6 V8....
Recently it started running horrible. Rough idle, drives badly, hesitation, etc. Check engine light is on, code P0171. I cannot find a vacuum leak, and i am pretty much at a loss. Before it started running poorly i replaced the thermostat, and flushed the coolant. I am assuming this is a coincidence.
View 1 Replies
I have a 03 explorer sport trac. I am getting code p0507. So someone told me it the Mass air flow sensor. so i went to the auto store and pick up mass air flow cleaner so the light went out for 3 day .now it back on again no air leak that i can see. Not saying there is none. Now someone telling me it a egr .
View 8 Replies
My Explorer CEL just came on today, when checked it only brought up a code P0171. I have read through a bunch of the post and it seems most people get two codes where as I only get one. Also most say their vehicles run rough, mine runs great, so I am at a loss as to what to check or replace first. There does seem to be a slight ping when under load.
View 7 Replies
I have a 2000 Excursion with the 7.3L. We bought it in February of last year with 81,000 miles on it, and it has 111,000 miles on it now.
First problem:
It threw a code today: P0683 indicating a communication issue between the Glow Plug Control Module and PCM Communication Circuit. Other than the code, the truck isn't doing anything out of the ordinary today. Drove it about 40 miles, up to 80 MPH, problem three below did show it's head once, but other than that it ran great.
Second problem:
Ever since we've owned the vehicle it has done a strange surging/near-stalling thing (for lack of a better word) when it's started up. It only does it occasionally, and the problem seems to appear, and then go away for several weeks or months only to reappear. Here's how it goes:
- Start truck
- After starting the truck immediately begins to surge (rev?) and then nearly stall.
- It will do this over and over, about one surge/near-stall cycle per second, until I tap the accelerator, at which point it stops immediately. So far it has never stopped on it's own, but has always stopped with a tap of the accelerator.
Up until recently I chalked this up to "huh, that's weird" since the truck has otherwise run fine.
Third Problem:
Every once in a while the truck will hiccup while it's up to speed. It only seems to do it at highway speeds, typically between 55-70, and the hiccup typically only occurs once.
The first time I distinctly remember it happening was right after I had replaced the Camshaft Position Sensor (approximately 5-6 weeks ago).
While digging around online I found one other guy say his truck started doing the same thing after replacing the CMP in his F250 with the same little plastic gray one I used. So that problem might be caused by that part.
My Thoughts:
It seems like the run-away favorite for fixing problem one is to replace the GPCM. I've dug through a couple hours of forums this afternoon/evening, and it looks to me like the GPCM is the culprit the vast majority of the time when code P0683 comes up.
I'm thinking problem 2 might be an ICP issue. I can't find any previous forums anywhere that describe the exact issue I'm having - or really anything very close. Maybe it's out there, but I couldn't find it. So I'm really grasping at straws.
Problem 3 could either be related to the ICP (if problem 2 is an ICP problem) or it could be due to the new CMP I installed (the cheap gray plastic one from Autozone). It's possible the hiccup has been around longer than I think. Half the time when it happens (or does it?) I can't decide if it was a hiccup or a bump on the road I didn't see. I am sure it's happening at times, but there are other times I'm not sure if it was a hiccup or a bump I just didn't see. So I think it's possible it's been going on longer than I realize, and I noticed it that first time because I had JUST been under the hood and pretty finely attuned to how the truck was running as a result.
I'm about to hitch my 35' camper to this truck and haul it a few hours and I'm not feeling real confident right now. Problem 1 hit today, problem 2 is more prevalent than every right now, and problem 3 has been hiccupping for 5 or 6 weeks. I'd like to get at least problems 1 and 3 sorted out before hauling 8,000 lbs if possible.
View 8 Replies
