Ford - Explorer :: 2002 XLT - Oil Pressure Gauge Never Worked And 4x4 Light Flashing
Jun 3, 2012
I have a 02 explorer XLT with the 4.6L and the oil pressure gauge has never worked (the three years I have owned it) I did an oil change yestarday and replaced the sending unit thinking that was the problem but the gauge is still not working. What other problem it may have? 4x4 light flashing (instrument panel looks like a xmas tree)...
View 10 Replies
Advertisement
My factory gauge on the dash reads Zero. I have put on a mechanical external gauge and it reads normal.
View 2 Replies
I replaced my wheel bearings and wheels roughly 6 months ago, right after I noticed my wheels gittered when turning at low speeds. I assumed this was a power steering issue or the new tires. I have now learned from this forum that it is most likely stuck in 4x4 HIGH but has no indications on the dash. Just yesterday though the actual 4x4 High light started flashing in different variations. I get 6 flashes one time, then 8 flashes 2 minutes later on the dash and so on back and forth. When I stop I can put the truck in 4x4 high and the light stays on, same with 4x4 low. Then when I go back to 4x4 auto they go off but I still feel gittering while turning at low speeds. What would cause this? I see a lot of people replacing the Xfer case control module but no one seems to have the same problem.
2002 4.0L XLT 135k
View 3 Replies
2002 F150, 4.6 V8, 140k miles. Oil level good, oil was changed 2 months ago.
Driving along one day, out of the blue oil pressure light comes on, oil pressure gauge went to zero.
Engine did not run hot, no bad engines noises that I can hear.
Upon restart, oil pressure will be up on the gauge for minute or so, then goes to zero and oil light comes on.
Asked around, some say oil pump, some say oil filter or pickup tube.
View 5 Replies
I am working on my friend's '02 Explorer 4x4 with 4.6L engine with 122k on it, the dash is telling him that he has low oil pressure. When it first came on he was an hour away from home, what he told me he did was pull over and checked his oil level right away. He found that it was still full and since the engine wasn't making noises he resumed his trip home. During the drive home he said the dummy oil pressure gauge would read normal then drop all of a sudden then come back up again after so long.
When he got back home he changed the sending unit plus the oil and filter and his Explorer still reads as if it has no oil pressure. The needle does not read anymore, he noted to me when he pulled the filter off it looked like it did not have the normal amount of oil inside it. I did not get to see it so I can not verify that. When he starts it it kind of sounds like it has to fill the filter every time like a fresh oil change, rattles around for a second then smooths out and sounds good..
So is his oil pump to blame for the light being on or is there something wrong with the gauge in the cluster? I have not hooked a mechanical gauge up to where the sending unit threads into so I don't know how much pressure it actually has. If not the oil pump what could be the cause? My other friend and I looked at the oil that came out of the new filter and we thought we saw metal specs in the oil. Is it new engine city time? It has such low miles to need an engine.
View 6 Replies
Wife's truck- 2002 v8 limited explorer with 116k... Yesterday she calls and says the od light is flashing and the message center says check transmission. She drove it home then when I got home the light was off and all seemed ok. I am taking it to have the codes read and hoping that my mechanics scanner picks up a code.
View 2 Replies
It's a 2002 explorer, 4.0, 5R55W trans, all was fine then O/D light starts flashing, so I limp it home. Trans isn't slipping, every gear works, it does kinda bang into 4th but is otherwise normal. Took it to auto zone to have the code read, but no codes found. Disconnected battery to see if it just needed a reset maybe, let it sit for a few hours, reconnect, OD light still flashes. Borrow a different OBD2 tester, still shows no codes, still drives the same just bangs into 4th. I've read up on the solenoid pack replacement, just kind hesitant as I feel like I'm guessing at the problem and might be throwing money away.
View 2 Replies
How to reset the Anti Theft on my explorer? The light is flashing fast and the engine won't start. Without the anti theft being reset the truck won't start. Been checking around to find an answer but can't find one...
View 7 Replies
I have a 2002 ford explorer with 70000 miles on it. The problem is that the oil pressure occasionally go from normal to no pressure immediately. Then within a minute it pops right back to normal. It has happened when I first crank up and sometimes just going down the interstate at a normal speed. My fear is that the oil pressure is really gone and there is a pump problem but with it either working or not I fear it could be a sensor problem.
View 5 Replies
My daughter has a 94 XLT with 4 liter OHV. This the first time I have noticed a vehicle to have both an oil light and a pressure gauge. Periodically the check oil light will come on, but the gauge shows very good pressure. The oil level is full. I'm not sure what to make of this. I know the engine was replaced with a rebuild but no idea how many miles are on it now. Oil looks fairly clean tho it is due for an oil change I think.
View 3 Replies
I have a few problems with my explorer. I was just wondering if there's any way I can fix them on my own instead of paying a mechanic. I
1. back passenger window wont roll down .. .
2. Gas gauge fluctuates can't get an accurate reading on it .. .
3. service engine light comes on for a couple days, then goes off .. .
4. shifts hard if i go over 65mph and then slow back down .. .
View 3 Replies
I have a 2002 Ranger V6 3000 with 100K miles. Can I add a higher viscosity oil since my pressure gauge is acting up. I changed the sending switch twice but the gauge still acts up occasionally. I was thinking of adding 10/ 30 on my next oil change. I do live in the area where the air temp is quite high in the summer. The truck runs well except for the oil gauge, in my opinion, is giving false readings.
View 14 Replies
The tire pressure warning light has been on in my car for about a week. The dashboard computer says that the tire pressure in the front right tire is 17 psi, but when I use the pressure gauge, the reading is almost 40 psi. Is this something I should be concerned about? What could be causing this problem?
View 16 Replies
2009 Ford Explorer, 6cyl, 4L, 33K miles. When its started up, the message "Tire Sensor Fault" appears along with the low tire icon flashing (steady light after ~30 seconds). I can then press the reset button on my dash to clear the message. However, the tire light icon stays lit. I've checked and re-checked the tire pressure in all the tires (spare included) and I'm right at the recommended 32-34 psi on all the tires. No signs of leaks at all. I'm assuming one (or more) of the tire pressure sensors have gone bad and there's no way for a garage (or myself) to identify which one or repair this. Should I assume a trip to the dreaded dealer for this problem ???
View 10 Replies
Started the morning with oil pressure gauge dropping to 0, gave it a few minutes checked oil, it was fine. Restarted truck, pressure went back to normal. Drove about another 30 miles pressure gauge would drop but would rise when hit accelerator. I was driving about 60mph, gauge went back to 0, check engine light came on and within a matter of seconds, a whining noise started, pulled over before i could completely stop, it died, and now won't crank.
View 6 Replies
2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
View 10 Replies
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
View 13 Replies
Just recently purchased a 2004 Eddie Bauer Explorer w/ 110k. Took a Snap On scanner with me to look at it. ABS light was on and I also get a 4x4 high flashing light every 2-3 minutes. Blinks 8 times then goes away. Scanner showed the RF speed sensor isn't sending any mph signal back. Just reads 0. Will my problem be a new sensor or is the sensor getting a dirty signal trying to read dirty teeth on the hub? Also, will fixing this stop out with the blinking 4x4 light?
View 1 Replies
Any reason why the OD light flashes, and how to fix it with out spending an arm and a leg?
Light flashing on a 99 ford Explorer.
View 3 Replies
Recently my check engine light came on. I understand this isnt such a big deal, but then my engine started "skipping", and my overdrive light is now flashing. my car will stall if i come to a complete stop without putting it into park or nuetral. I dont know what to do.
View 7 Replies
1996 Explorer xlt 4.0l ... I ran into this issue a few years ago on a drive up through the mountains. Had the tranny replaced shortly after.
Rebuilt the engine once due to leaking head gasket.
Rebuilt it again 2 months ago due to leaking rear main seal.
Had a new torque converter installed during last engine rebuild, so tranny has been shifting and driving like a dream.
Just drover about 30 miles on highway, all pretty flat. OD light started flashing. I didn't notice ANY change in the way it was driving, sounding, shifting... anything! I know this is some sort of oddball error with this transmission in this vehicle, but i need to know if it requires further investigation.
Also, sometimes upon starting up (i am a pizza deliver, so i often shut it off and start it again 1 minute later) the OD and (i think) the 4x4 light flash at the same time, and my windows wont work for around 15 seconds. I've also noticed that my ABS will sometimes kick in randomly on dry ground during slow stops.
I am not in the mood to just start dropping cash on random sensors or modules or repairs if i can find any solid evidence of an issue (i've been battling an EGR issue for 4 years). I was thinking maybe the vehicle speed sensor?
View 1 Replies