Ford - Explorer :: 2002 - Temperature Gauge Not Working After Replacing Engine Coolant Temp Sensor
Feb 3, 2010
2002 ford sport trac.I have been having an ongoing issue that started with the engine cranking but would not turn over until an hour passed. After replacing multiple parts (cam shaft sensor, crankshaft sensor, ignition pack) I am now down to poor fuel economy as the last of the issues (roughly 12 in the city and 15 highway). I was told the issue may be the engine coolant temperature sensor going bad so I decided to replace it. I found this was very difficult due to it being a plug and locking pin design and in a very tight spot in the engine.
I tried to purchase a replacement and the parts store kept trying to insist on selling me a part with threading. I finally found someone that figured out the issue and found the part for the 2001 sport trac had the same plug style with clip that did fit but was shaped a little different on the sensor end which I assume was due to being aftermarket. I noticed that there were two plugs side by side and the one easiest to access was on the left and I was told the one on the right was the sensor that gave the temperature reading to the gauge.
After installing the engine coolant temperature sensor I found the temperature gauge on the dash now will not respond and is sitting below the cold end of the gauge completely off. Is it possible this is because the part was for a 2001? Is the sensor on the left (passenger side) the engine coolant sensor?I would hate to put the old sensor back in just to test if that's the issue due how difficult it was to put that locking pin back on. What to check that could resolve the gauge issue before pulling this sensor back out?
View 3 Replies
Advertisement
My '04 Passat 4Motion (station wagon) engine coolant temperature gauge, fuel gauge, and outside temperature display all stopped working in the same time. Interestingly enough, car has 32K miles and just ran out of manufacturer warranty 2 months ago.
What could be happening? Should I be checking fuse box or this may be related to some more serious failure?
View 1 Replies
I drive a 2001 Jetta with the 2.8 v6 with ~125k miles
So for a while my car was giving me a false read on my temperature so I replaced the sensor. I actually followed instructions from a thread on this site. [URL] ....
Now when I go to drive my car, it runs sluggish and misfires if I really give it some gas. CEL is on(however does not return a code when hooked to a computer), and flashes when gassed hard.
I've checked to make sure spark plug wires were reconnected correctly and securely. No leaking has occurred from the temp sensor. shift rod drive unit is reconnected correctly.
View 1 Replies
2009 Ford Explorer, 6 cyl, 4.0L, 74K. Read code w/scanner - "P0128 - Coolant Temp below thermostat regulating temperature". Assuming this is pretty straight forward but was wondering what the most likely culprit is (?thermostat?). Ironically, this code popped about a week ago, I cleared it and actually got my inspection sticker earlier today and then later in the day, the CEL came on again and once again, the P0128 code. The coolant level is perfect so I know there aren't any leaks.
View 5 Replies
Having a problem with my temperature gauge inside the truck. No matter how far or long I drive, the needle barely moves off of cold. Would the thermostat be the likely suspect? If not, what else could it be? There is no "check engine" light on and my ODB2 reader reads a temp of around 70c solid. If it is the thermostat, where is this part located in the car and would I need to replace JUST the thermostat or are there gaskets/housing-type things involved as well.
View 7 Replies
Temperature gauge quit working after changing the thermostat and coolant.
With the engine off, I disconnected the single wire from the temperature sending unit and switched on the ignition without starting engine. The gauge pointer stayed in at the Cold mark. Using a Jumper wire, I grounded the sending unit wire and the needle on the gauge went to the Hot mark.
I quickly turned off the ignition, and replaced the sending unit with a SW-2328 (F1SZ-10884-A) Temp Sender. Warmed up the engine, but still no reading on the dash gauge.
View 8 Replies
Basically my coolant temperature gauge either reads as the hottest it can be, or the coldest. It doesn't jump around a whole bunch, but it's always all the way to one end or the other. From what I've read there seems to be a lot of different temperature sensors, so I get a little confused with all of the abbreviations, but I'm fairly certain I checked the correct one, next to the thermostat housing.
Using a multimeter I checked the resistance of the sensor, and it was around 600 ohms about 30 minutes after it had been driven. I'm not sure if this is where it should be or not, but it was rising as the truck cooled off.
Anyway, I'm not sure if I just tested the sensor incorrectly or if there could be another issue. A friend of mine suggested that the thermostat may have gotten stuck or something, but it doesn't seem like the gauge would switch at all if that were the case. What I should check to try and fix this.
View 7 Replies
I drove my 99.5 7.3 F-350 1 mile to a friends and hooked it to the OBDII to get a code for my abs light.it had not been drove all day. we hooked into the pcm and he noticed the temp at 375* it was idling. is this right he didnt think it should have been that high???Will the engine coolant temp sensor, if it were bad,show a high temp of 375*? On the OBDII it showed a temp of 375* .....
View 14 Replies
I have a 2003 Passat 1.8t(B5.5) and I need to change my engine coolant temperature sensor. I have search and found conflicting answers on the forums as far as it location and description. From what I can see it is located near the bottom right hand corner of the radiator(Driver Side). I have removed the sensor and I did see some antifreeze spill out. I examined the sensor and it is blue in color with a rounded top. I called my local auto zone and received a replacement part but it is green and looks a little different.
I understand that the blue one that I removed is no longer produced. My question is is this the right sensor and the right location? All the write ups I can find say that it is located in the back of the engine yet I cannot find one there. Also when I replaced the blue senor with the green one the fan on my car is spinning at high speed(the AC fan) and will not idle. I am wondering if the new sensor is faulty/ incorrect or if i simply replaced the wrong sensor.
Here is a link to the replacement part I used : [URL] .....
View 1 Replies
Bought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 Replies
I was going to order a ECT gauge and was wondering where to mount the sensor. I have already used the port under the T-stat for the coolant filter. The gauge sensor is a 1/8 NPT. Would the block drains be a good location, or is there another location that will work.
I know the coolant filter housing has a port, but I would prefer the sensor be on the motor.
View 11 Replies
I got my car back finally and on the way down the belt way i started sliding around a big turn and I get home to see my temp gauge way up and all the coolant went all over my engine .
I took it to a shop the did pressure test and that was fine, But the also found jell around the thermostat. The other thing they said is that it had air bubbles in it too. They said exhaust bubbles. But when they ran it it didn't heat up any more. They said its the early stages of blown head gasket ..
I took it to the dealer right away and they are telling me they cant find any thing wrong. Both places asked if i put stop leak in there but I never added anything to my car. So I am lost and don't know what to do.
View 10 Replies
So I got a 98 GMC sierra and the ect sensor that is on it only had one wire running to it. Obviously the previous owner tried to make something work. I bought a new ect sensor and pigtail to rewire it but can't find the ground wire anywhere. Looking for a wiring diagram?
View 14 Replies
My radiator gave way on the highway, and by the time I noticed it the temp had maxed out the gauge and all the coolent was gone. So, I only have 90k on my '94 Camry and I'm debating whether to tackle repairs and perhaps a rebuild if necessary. What's the likelihood that there's damage to the rings, bore, crank, valves, etc due to the overheat? How much repair am I potentially looking at and what can I check without a tear-down? I'd like to get it running again since I just invested in new struts, brake calipers and MS and tires (not to mention that it has been pretty-much worry-free until now), but I want to know whether it's even worth my while.
View 6 Replies
On my 97 X SOHC, I have a temp gauge that is rather erratic. It reads high even with the engine off and cold and rises when the engine is running to the point the "Check gauges" light illuminates. Then bounces to normal then back near red line. This cycle continues.
To evaluate this, I bought a scan tool and the ECT reads as expected, around ambient to start, gradual climb till the thermostat opens, then hovers there while the radiator does its thing. Heater works as expected. So I'm fairly confident that my X doesn't have a cooling issue.
What my questions are: Can I disconnect the temp sender so I'm not watching the gauge bounce around and then the Check Gauges light is available for other issues that arise?
Does the check gauge light also send a signal back to the PCM?
Can I do any damage to the truck or will the PCM throttle the power back and flash the Check Engine light if a real cooling issue materializes?
View 4 Replies
My sister drives a 2005 Nissan Altima. I am not real familiar with Japanese OEMs but I do most of my own repair work on my car (which currently has issues of its own). What's wrong and how do I go about making the repair...
View 8 Replies
My temperature has been randomly dropping, them back to middle, and recently my engine was overheating because I'm guessing the fans didn't turn on, because I'm also guessing, the engine didn't know it was overheating?
Anywho, during my replacement, I made sure to get rid of the pressure, and the car was cold. I tightened the cap again, but when I took the sensor out, all the coolant spewed out.
Now if I understand this correctly, do I have a leak? I figured the leak I had was coming from the temp sensor as it is.
Here's some pictures for those who'd like to see ....
View 4 Replies
I have a 2005 mk4 gli and the other morning I went out to start my car for work and all I got was crank no start. I then realized my fuel pump wasn't priming when I opened the driver door. After work I came back and checked the fuel pump fuse and swapped the relay with another I had, still nothing. A buddy of mine decided to check the connector at the fuel pump for power, using a power probe I believe he hit all or the majority of the wires with 12v of negative and/or positive power. He then unplugged the connecter and plugged it back in and the car fired right up. But I noticed that my fuel gauge, engine temp gauge, and outside air temp readout were all not functioning. I've searched and searched without being able to narrow down a solution.
View 19 Replies
02 6.8 4x4 excursion. When I start the truck cold, the trans temp gauge immediately moves to "running" temp. Not really sure how this happens, I'd figure that if the xducer was trash it would ride all the way high or all the way low. What's happening here? I'd sure like a functional gauge...
View 6 Replies
My 1988 240DL wagon....the engine temp gauge is not working? is see the wire that goes to the sensor in the engine block, it is there and connected to the sensor. is there a way to test the wire? I have purchased a new sensor, but I have not replaced it yet.
View 1 Replies
I have a 2005 mk4 gli and the other morning I went out to start my car for work and all I got was crank no start. I then realized my fuel pump wasn't priming when I opened the driver door. After work I came back and checked the fuel pump fuse and swapped the relay with another I had, still nothing. A buddy of mine came to me and decided to check the connector at the fuel pump for power, using a power probe I believe he hit all or the majority of the wires with 12v of negative and/or positive power. He then unplugged the connector and plugged it back in and the car fired right up. But I noticed that my fuel gauge, engine temp gauge, and outside air temp readout were all not functioning.
View 1 Replies
