Ford - Explorer :: 2001 Won't Crank - No Click When Turn The Key - Dash Powers Up
Sep 3, 2016
My son has a 2001 explorer sport that he keeps at college. The vehicle sits alot more than it runs these days. Recently it some times does not want to start, no click when you turn the key. He got it home today, and after I changed oil, it would not start. I have no ground to the starter relay in the power distribution box.
I have no electrical schematics, where the ground for the starter relay comes from ? If I remove the relay and run jumper wires from the box to the relay, i can make the vehicle crank when i apply another ground source to the relay....but it just cranks, will not start.
View 10 Replies
Advertisement
2002 explorer 4.0l. No crank just click new starter in and cables hooked to battery...
View 1 Replies
I have a 99 f150 2wd v6 4.2 liter engine. Im going to sum up what happened and what I've done so far. One morning truck wouldnt start. Wouldn't crank, turn over, or even make a click click noise. I tried jumping it just to be sure but it didnt do anything. Battery is fine, interior lamps, displays, and radio all work fine.
I took the starter off, had it tested, it was bad so i got a new one. Still had the same problem. Finally, i got underneath the trunk and bridged the positive and negative on the starter solenoid and it fired right up. So the starter is not the problem.
Next I looked into the starter relay, if I bridged the positive and negative on the starter relay it fires right up just like the starter. But since that is only bypassing the starter relay, it didnt tell me whether the starter relay was good or bad. So I got a new starter relay and it worked! It started with the key with no problem 3 times! I thought the problem was fixed but when i tried to start it an hour later, nothing... Same problem as before.
I checked all my fuses, none were blown.
I'm under the assumption that either something leading to the starter relay is making the starter relay go bad OR there isn't enough power going to the starter relay. Maybe something in the ignition, even though my accessories are all still working.
It is the only vehicle I have to and from work. For now I am getting by with bridging positive and negative on the starter relay to start it but that is only a temporary fix.
View 8 Replies
1998 Ranger, 3.0 liter manual transmission. The vehicle recently has had the engine replaced. Still a 3.0 Liter, but possibly is from a 1995 or 1996 Ranger. Replacement motor from a wrecking yard, appears to have been sitting for quite some time prior to purchasing. I had a friend change the motor out after getting the vehicle a few weeks ago.
Ranger drove fine for a week, but this morning it wouldn't start. One click is all it would give when you turned the key. Thinking the culprit was the all in one starter/solenoid, I replaced it with a new one this morning. Now the solenoid will click continuously when the key is turned, starter still will not rotate then engine.
Battery tests good - 12.4 volts; connections appeared fairly corroded.
Here is what I have done:
- Clipped off the first half inch of corroded terminal leads, replaced both sides with new battery connectors and wire brushed connections off at battery and starter.
- Replaced Starter
- With "S" connector disconnected, attempted to bypass starter connections and short terminals to see if a faulty clutch position sensor was to blame; shorting did not produce anything other than turning the key did.
- Paralleled an additional cable from battery to starter terminal to see if corroded wire connections were to blame; still just clicked repeatedly when attempting to start.
Crankshaft does rotate manually, does not appear to be seized up. Unsure of what else to check for. Not confident in friend's engine installation abilities, he may have screwed up something I'm not thinking of. On the other hand, I don't believe I would have been capable of swapping out the motor myself.
View 3 Replies
I was told by the dealership that the battery was bad and needed to be replaced ( which I did) I went out to my car this morning and had the same problem. When I turn the key nothing happens. When I turn the key you hear a click but that is it.
View 3 Replies
Have a 97 Ford explorer. Over 270,000 miles on it. Recently had Crank sensor, Crank case vent tube, plugs wires replaced along with intake manifold gaskets. Also had fuel injectors cleaned out. Now i cant get it to turn over. Went to store, truck started fine, came out and click. Thought it might be the battery even though its also brand new but no, had the starter checked, it is also good. Put test light on all electrical having to do with starter and found all hot wires and good grounds. Finally bypassed the solenoid for starter and still nothing but a click. I also checked NSS to see if that might be it but after putting it in reverse, the reverse lights came on, and even jiggled shifter in park and neutral to see if that might work but still just a click. Not sure where to go from here short of buying all new parts but doesn't make much sense to do that if they all appear to be working properly. Don't have a volt meter to check voltage.
View 5 Replies
I have an 02 F250 6.8 with 51,000 miles on it. I recently replaced the battery about a week ago, and only actually drove it yesterday for the first time since replacing the battery. I drove it about 25 miles, parked, and when I went to restart, it wouldn't. The starter doesn't crank, so I mean its not a cranking issue as in cranking, and not starting. It only clicks at the relay when turning the key. It acts like when you try to use a wrong chip coded key.
All of the dash lights came on, and I can hear the relay clicking, but that's it. I swapped the relays around, and no luck. If I let it sit a while, about an hour, it will fire right up. The battery cables are tight and free of corrosion. I am curious, since I just put in a new battery, could this be the culprit? Why will it start fine cold, but not hot? I have NEVER had an issue with this truck until now.
View 14 Replies
Alright so I have a 99 7.3l. One day I went to start my truck and when I turn the key to the on position all is normal and then when I turn it all the way to crank it nothing happens. I hear a relay click ann thed that's it. Me and a buddy of mine spent quite some time on going through the entire truck. The starter was replaced, the neutral safety switch was replaced and the ignition switch was replaced yet the problem is still there. We then discovered that fuse #20 under the dash keeps blowing with every turn of the key. The manual states that this fuse is a starter motor relay coil PCM ( gasoline only). So if it's gas only why is it even in there. Let me just say that I can jump the fender mounted relay and the truck starts.
View 7 Replies
My friend (yes, really, a friend, not me) parked her 2004 Dodge Caravan in the driveway the evening before. The next morning it would not start. No crank, no grind, no click, and no dash lights, nada, nothing. She took it to the shop she's taken the car to for years for repair and maintenance. She trusts them. They've replaced the battery and run a full diagnostic on it, but are unable to solve the problem. The shop is telling them her it could run into the thousands just to figure out the problem. What could they be missing?
View 4 Replies
Turn key
Click
Headlights do not dim at all
No crank
This has happened three times now, about a month to six weeks apart. Eventually it starts exactly like normal. I can't put my finger on exactly what I did between "not crank" and "crank like normal" but it wasn't anything significant, that's for sure.
Tonight I cleaned the battery terminals, but they actually looked very good. Looking back, I should have checked how tight they were before taking the cable off, but I didn't. Not sure whether a loose cable could explain these symptoms.
I was thinking this was starter or solenoid? Any other diagnosis consistent with the symptoms?
View 14 Replies
I have a 2002 F-150 xlt 4x4 5.4l V8, 96k miles. been sitting about 3 weeks i went to start it and nothing.. thought ok jump. We tried jumping/charging the battery nothing. then we switched batteries from running car same thing when i turn key just hear a click in dash. battery light remained on even when we swapped out. The theft light was off as well.
View 1 Replies
I have a 2004 Excursion with the 6.0 diesel 189k kilometers. Had an egregious delete done about 3 weeks ago. A couple of nights ago the temperature was about 10 degrees f and Whalen I started her it sounded like electrical arcing or grinding. She started and off I went. The next morning it was 0 f went to start and made the same noise and then just stopped cranking. Now when I turn to start I get nothing except the relay click under dash. I tried jumping the solenoid and got nothing. Someone told me that my ground connection might be off the starter. Problem is I can't seem to get at the starter.
View 3 Replies
I just bought a 2004 hyundai accent 1.6L standard transmission on the 13th of June, ran great drove it everyday, was driving fine when I came home monday night, went to drive it yesterday and get nothing, turn the key no click, no crank, the radio turns off as it always did when you try to start, I checked the fuses, and the battery shows twelve volts on the meter, what could cause this to abruptly happen?
View 3 Replies
Ok, I have a strange no start issue right now. My excursion won't start. I have power to everything and both batteries are at 12 volts or a bit more but the starter won't engage. If you turn the key to start all that happens is relays click under the dash and the airbag light flashes. It almost seems like the transmission is in gear. It did this twice about a month ago and has been fine ever since until today.
View 8 Replies
My radio never turns on with the car right away. The only way it turns on is when i crank my heat on for about 3-5 minutes. Then it powers on. Fuses seem ok. The service center didn't know what could cause this...
View 3 Replies
Car had been running fine and all the sudden turn the key and get nothing. Dash lights come on and there's a click in glove box but nothing from starter. I have 0V at ignition post on solenoid with key in start position. I can short the 12V post and ignition post with screwdriver on solenoid and starter and engine crank as normal but car won't start. Further checking I have 0V key off at ignition module, 12V with key on. A connector outside firewall between ignition switch and transmission neutral safety switch. I took this apart, it was a 7 pin with 2 of 7 blank. The red wire I had 0V key off, 12V key on.
Then I dug into the steering column area. 12" or so down from the key there is a connector with a rod coming from the key area down into it. I assume this to be the ignition switch. The rod is supposed to move and is attached to a plunger that pushes into the connector. I assume this rod is attached to the key. When I turn the key the rod never moves. So I thought ok clamp some pliers on the rod and push it into the connector manually, it should make connection and start the car. When this had no results I am now at a loss as to where to go next. Further thought, how did I get the 12V readings in several locations with key on if ignition switch appears to be faulty. I'm not sure if it's faulty or not, things don't add up. I didn't dig into the steering column where the key is yet because I will have to remove airbag and steering wheel to do so.
View 10 Replies
My wifes explorer will not attempt to turn over. When I turn the key to the run position the dash does not do anything. I dont get any indicator lights or anything from the dash. And also the PATS light in now a steady dim light. So now I am confused and don't know where to start on this one. Is this a PATS issue or is my instrument cluster the problem? I did read the TSB on the cluster.
View 2 Replies
I just got back from a deployment and my Dad changed out the battery on my 06 F150. He said it started up fine for him, but I tried and it powers up great but won't turn over. Everything electrical still works, but the engine doesn't even try to turn over.
View 2 Replies
We have a 2004 2.4L 4 cyl Santa Fe. Turn ignition key get a click and engine will not turn over. Push key in harder and engine may start fine. If it is the key ignition switch or something else. is there somewhere I can look to see how to remove the ignition switch?
View 4 Replies
Been battling this for several months. Sometimes, the truck will crank but not fire. Several attempts, then apply gas pedal, eventually will start. I have read through and searched much of this forum. Let me start with this, every part I have replaced has been with Motorcraft parts. I have done the following:
1. Replaced IAC. Ports are very clean.
2. Replaced fuel pump & filter.
2. 5 Voltage at pump connector is good AND it lights a heavy bulb. Not losing voltage to pump.
3. Replaced MAF sensor. This changed it. Stopped doing the no start for about one month. Then began doing it again.
4. Replaced MAF connector, soldered in a motorcraft connector. Good for 3 days.
5. Have checked connector pin tension and condition at crank sense. Good.
6. No codes.
7. Always shows RPM on scan tool while condition is present.
8. Once it starts, it never dies, not rich, not lean. Fuel trims are great and runs mint.
9. Technician is now in loony bin.
View 14 Replies
2001 F150 4.6 V8 Triton
Automatic
Battery Tests Good
Starter Tests Good - I saw it spin and come out at the testing station at Autozone
Ignition Relay (the one in the fusebox)- New (8mo.)
Switch on the firewall on passenger side of truck - New (8mo.)
Battery terminals/connectors - Tight, no movement, Cleaned within the last week.
Starter connections - cleaned within the last week.
I am having trouble with my truck not starting. The issue has been occurring on and off for over a year. Usually, it happens about once a month, regardless of weather.
I turn the key, and there is one click. Usually at this point, I can use one hand to gently pull the shifter "up" towards park and turn the key again and it will start. Recently it is not starting when I do this. I have tried many times, and have tried to start it in Neutral (is that even possible with an Automatic?).
With the key in the "ON" position, I go under the truck and jump the starter cellinoid. I am jumping the small post to the big post where th wire comes from the battery. I do not touch the post that the wire goes into the starter.
I am very confused because it starts just fine without fail and almost instantly when I jump the posts. It is drive-able this way, but I would like to resolve this issue, and resume using my key to start it since the issue doesn't seem to be resolving itself as it usually does.
A friend told me about the Ignition Starter Switch inside the Column. If I have time I will attempt to start the truck with a screw driver on the switch tonight to narrow down the issue.
View 9 Replies
