2001 explorer sport, need to reset and clear check engine light I know the problem a small pinhole in exhaust that opens up and i fill it in How do i reset check engine light...
View 1 RepliesMy 1998 Explorer with 120,000 mile on it. The check light just came on. I have had several auto part stores plug in the scan tool and there were no error codes. I'm looking for the reset button location. I am also wondering should there be something missed by the scan tools, will the light activate should there be a real problem.
View 9 RepliesI have an 01 Explorer Sportrac with a 4.0, 105,000 milles. Got the check engine light with the EGR low flow code. I get this code about once a year and a new DPFE usually takes care of it. I get the sensor from Advanced Auto which explains the short life I am guessing. Last time i replaced the sensor the light came back on a couple weeks later.
After highway driving smoke starts pouring freon under the hood, passenger side, but by the time I get the hood opened its done. Cant tell where it is coming from. Could a faulty DPFE cause the smoke or do you think the EGR valve may be sticking? I was going to try a Ford DPFE this time but I hate to just throw parts at it. Where do the smoke is coming out of, air filter box????? cant see anything else over there related to the EGR system......
I bought some long beams at the local lumber yard. So drove home with the rear cargo door open. The ABS light went on brakes were pulsing mildly and making an odd sound. I cant see why the rear cargo door would have any connection with the ABS system so I assume that's a coincidence.I took the van to the local car store they scanned the code. It scanned code 4 indicating the passenger front sensor. I replaced the sensor but the ABS light is still on. Is there a reset function to clear the code disconnecting the battery didn't work? Or am I looking at another component failure?
View 2 RepliesJust replaced the alternator in my 1993 Ford F250. How do I reset my check engine light? It keeps coming on after I drive for roughly 5 to 10 minutes.
View 7 RepliesAfter I finally got around to replacing my ABS pump I went to get my smog check done. Passed except I didn't drive enough miles to qualify.The SMOG tech told me to drive 150 miles and come back. I drive the 150 plus miles and within that time my check engine light comes on. I go to the shop and have it reset.
How many miles do I have to drive the car after a Check Engine Light reset in order to qualify for a Cali SMOG Check.
How do you reset the CE light on a 99 passat?
View 8 RepliesHow do I re-set CEL without a scanner ? I've heard about battery disconnect , but concerned about causing other issues . 2000 Passat V6 GLS wagon 4motion Tiptronic .
View 18 RepliesI have a 2002 Passat. How to reset my check engine light. I need to get it inspected and it won't pass inspection until the check engine light is not on. Last year I took it to a mechanic who could find nothing wrong with it but reset my check engine light for me and it cost $250. Is this something I can do myself? I've had the car since it was new and the check engine light has gone on and off periodically for the past 10 years.
View 10 RepliesFilled up my 2012 Lexus Rx450h in NJ. They don't have self-service there, so I don't blame myself, but gas cap not tightened. Check Engine light is on, I tightened gas cap, light still on. Is there just a fuse I can pull to reset the warning light? There seem to be a few fuses labeled ECU. Exactly which one should I pull ? If I don't, how soon before it will it reset on its own?
View 6 RepliesI have a 337 and the check engine light came on a couple months ago and i got the clutch safety switch replaced. but I forgot to take the light back off with my friends snap on tool. the car runs fine now but another friend with a TDI jetta said something about a master ecu reset? something like turn the key in the on position then hold the gas pedal for like 15 secs? I tried it but nothing happened. I just want the light to go away...
View 6 Repliesi have a continuous Check Engine light in my 2008 ford explorer. Dealer recommend replacing a sensor but I do not know which sensor to change.
View 4 RepliesMy 2007 Explorer (XLT, V6 4.0L, 4WD, 175k miles) has been experiencing a check engine light, intermittently, for the past few months. I took it to AutoZone to read the code and they gave me a printout for P0193. For awhile, the light would go off after I filled the tank with gas (usually the next day) and would come again as the level in the tank decreased (typically around 1/4 of a tank). Then about two months ago, the behavior seemed erratic and I could no longer predict when it would appear. During the past couple of weeks I only recall seeing the CEL once (briefly); it's mostly been off. Saturday night I was out driving and it came on again.
About two hours later, my vehicle "conked out" on me. It started hesitating (it's been a very long time since I've run out of gas, but that's what it reminded me of). Fortunately, there was no traffic and I was able to get it off the road but didn't have enough momentum to get it into a defined parking space before it quit. I sat there for awhile pondering my options (not too many since it was the middle of the night and I don't have road service). After about 10 mins or so, I decided to see if I could get it started. It did start and I was able to drive it home (< 10 miles). It's been sitting in the driveway since because I'm afraid of getting stranded if I drive it again. BTW, I was low on gas when it died -- about 50 miles to E (was headed to the gas station when it happened, but took it home instead).
After everything I've read the past few days, I'm expecting that I need to replace at least the fuel filter, the fuel rail pressure sensor and the intake gaskets for the manifold. I am not a mechanic, don't have diagnostic tools, my funds are really limited right now and I'm pretty much on my own to figure this out.
Q1: For those who may have some knowledge about this particular issue, does the intermittent nature of the CEL give any clues to which part(s) might be malfunctioning?
Q2: I found a replacement FRPS made by Bosch on Amazon, significantly cheaper -- is this brand ok or should i stick to Motorcraft?
Q3: Any advice on the manifold gasket replacements (is one brand better than another)?
Q4: Do I really need the special tool to replace the fuel filter?
The questions above are no longer relevant. I'm in the process of "locating" the sensor. I have the air hose and throttle body off. Now I'm looking at the EGR valve. It looks like I will have to disconnect the it from the large pipe beneath it. Will I also need to remove the two smaller bolts that mount it to the manifold cover, or can I remove the cover & valve together? It looks like those little buggers are going to be challenging since they are facing the back of the engine compartment. This is rather slow-going for me, but there's no turning back now.
I have a 99 Ford Explorer - w/217k miles. (2nd owner) .. I got an oil change 3 weeks ago, tune up 2 mos ago, and new brakes/tires within the last 6 mos, oh, and Brother-In-Law just recharged my a/c last week.
Runs well, and I hope to keep it for another few years, but having problem lately.
Check Engine light keeps coming on - I've taken it in, and they read the code, and it comes up with a misfire. Mechanic resets it, and it will stay off for a few days/weeks, and then comes back on.
I have 2007 explorer 4.0 4x4. Check engine light and wrench symbol on with codes po743 po750 po755 po po765 po966 po966 po970. Feels like it is now stuck in 3rd gear.
View 2 RepliesI have 2007 explorer 4.6 v8. The check engine light is on, and i can only fill the gas tank about 3/4 full, after moving the gas nozzle all around and taking about 15 minutes. I read a few different things while searching. Like vapor canister need to be replaced. or the vent hose needs to be replaced.
View 1 Replies2004 Sports Trac Got a check engine light: a code P0913. The truck , once in a while, hesitates like it not getting fuel. Is this a fuel pump problem or something else?
View 1 RepliesSo, last December, I was sitting at a stop light, when my engine suddenly started rattling. "Check Gauges" light on, ZERO oil Pressure..
Took car to mechanic, he removed the valve covers, and scoped out the timing chains with a camera, and found everything intack, and no chips out of the timing guides (125K miles on the engine). no sludge, nothing.
Engine runs fine (for 5 seconds at a time) no issues. Removed Intake to check the Oil Pump Drive Gear, all is well.
Removed Oil Pan Inspection Plate, All is well. ZERO plastic chips in the oil pan from timing guides, ZERO sludge, all is clean.
Back up to top of engine, pull the Oil Pump Drive Shaft using needle nose pliers from the top of the engine. BUT!!!
Only the top 8 inches of the Oil Pump Drive Shaft comes out! The bottom gear is not present! Is it still in the oil pump?
OK, so I need a new oil pump drive shaft. no Problem.. BUT: how do I get the broken oil shaft out of the engine before I put a new one in? Use a magnet? Rubber hose?
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 RepliesI have a 1996 Ford Explorer Eddie Bauer Edition 5.0, the check engine light is on and my code reader gives P0161 and P0155 both stating that the O2 heater circuit sensor is bad. I replaced all 4 of the O2 sensors in the truck, cleared the codes but they still keep coming back. I have tried for a few days now to find something online similar to this but have had no luck. I am not sure what else to do.
View 1 RepliesIs there a way to completely format / reset the navigation radio. The dealer wants to replace the head unit on a week old car. Seems like you should be able to clear the memory. Im getting a low memory error and it locks up. I hate to have the dash torn apart on a new car. I need to clear the phone contact but can't get to the phone settings because of the low memory issue. I think the problem stems from syncing over 500 contacts from my phone. Or maybe the 32gig USB.
View 1 Replies