I've checked just about everything, coolant level is good, engine gets hot, heater control valves moves, blend air door moves, the heater hoses don't feel as hot as I think they should, but the gauge reads in the middle, I burped it thoroughly and still no heat , blower works i actually can switch the blend air door manually, but no change! what am i missing? t-stat was changed too. 2001 sport trac....
View 2 RepliesMy son's 98 Expedition has no heat. The radiator and overflow tank are full, there's no air in the system. The radiator hoses get nice and hot but the heater hoses stay cold. We can hear the flow through the vents change when we change the temp control so I'm sure the blend door works fine. Seems like the problem is that no hot coolant is making it to the heater core. So I'm wondering if there is a diverter valve somewhere that could be bad that's keeping the hot coolant away from the HC or if a clogged HC is the only thing that could cause this.
View 1 RepliesOk I have a 97 f150 4.6L. My radiator has been bad for a while. With brown rust color. I replaced my radiator, thermostat, new upper and lower hoses. Everything runs great but I have no heat. I flushed everything including the heater core. Core is not leaking into cab, and both heater hoses are cold. FYI heat worked great until 5 days ago.
View 7 RepliesI have an '04 Explorer Limited and lately only blows cold air. I've read about the blend door motors but it's been too cold in MI to want to do much--so the truck sits.
When I was troubleshooting the problem I found that I'm not getting any vacuum signal to the heater valve in the coolant line. Before I contemplate removing the console & doing surgery on my dash I'd like to know for sure what position the valve should be in when heat is called for.
All the other vacuum actuators seem to be working normally and there's no disconnected hoses under the dash; and no leaks. Coolant reservoir is full.
I bought a 04 explorer with a bad thermostat which led to a bad head gasket, fixed that and managed to not have to buy the special tools or time it , but now that its running I don't have any heat. I have complete service records on this vehicle and there was never a complaint of the heater not working. The a/c works and the heat will adjust the a/c temp, but no heat. In trouble shooting it I found that I am not getting vacuum to call for the coolant to enter the heater core. When I apply suction to it, it will send the coolant. Even though I wasn't getting the clicking noise, I pulled the blend door actuator and it looks surprisingly good (not looking forward to putting it back in). Where to look next?
View 5 RepliesI drive a 2002 Ford Ranger and am wondering at what mileage should I change the heater and radiator hoses. The truck lives in Phoenix, AZ and is driven almost daily.
View 5 RepliesI've replaced my heater core and blend door in my 2000 and getting ready to button things up. Can I hook up the heater hoses after the plenum top is screwed on to keep the core from moving when pushing on hose connections?
View 1 Replies1998 Ranger. I have no vacuum to the heater control valve (see link below) and hoses are warm/hot to the firewall. Where to start troubleshooting?
More Information for FOUR SEASONS 74809
I really need to know. Since the X has 2 heater cores, how do the hoses run that connect the two together? Do they run in parallel, or in a series?
View 5 RepliesI'm feeling a bit embarrassed posting my delima, but I have a minor coolant leak which seams to be coming from where the heater hoses connect to the water pump and as well to the thermostat nuckle thingy. I have replaced all of the hose fittings with SS band clamps.
A couple of weeks ago I replaced the water pump, thermostat, alternator, rad hoses, belts, coolant sensor, PS tension pulley. The water pump is now tight and sealed. Since then the temperature gauge has been continually fluctuating from Normal to near Cold.
I was wondering if I should have placed some type of sealant compound where the heater hoses connect to the water pump and also to the thermostat nuckle thingy.
Initially, I thought it may be residual trapped air in the coolant system. But after a week, it became apparent that the heater hoses were leaking at the engine, and at the water pump, connections.
What puzzles and torments me is why is the temperature gauge fluctuating so widely up and down? This is totally weird.
Ok I have a 97 f150 4.6L. My radiator has been bad for a while. With brown rust color. I replaced my radiator, thermostat, new upper and lower hoses. Everything runs great but I have no heat. I flushed everything including the heater core. Core is not leaking into cab, and both heater hoses are cold. What should I do next FYI heat worked great until 5 days ago.
View 14 Replies2005 Elantra here with 120k miles
Problem: Not heat will come out unless
1) I don't turn on the Fan Motor at all. Very Nice heat will "bleed" out of the vents as long as there is no Fan on - on any setting.
2) Lukewarm heat will come out if I am giving the car gas or revving it. As soon as it goes back to idle or I am no longer giving gas it goes back to no heat at all.
Things I have tried:
Topped up the radiator and tank (radiator has been replaced)
Water pump replaced
No leaks
Thermostat is opening ( Upper hose gets hot, Lower hose stays cold for a while and then gets hot)
Flushed heater core with a garden hose.
Inlet hose to heater core is hotter than outlet hose but outlet hose is not cold to the touch.
Radiator cap has been replaced
Car does not run hot at all
I am working on a friends Neon and he been having an issue with constant overheating even through he has replaced the thermostat, the radiator, water pump and related hoses. However, he is missing the cap to the coolant tank and his heater core hoses are blocked, both incoming and outgoing. Could the blocked hoses be causes it to over heat?
View 1 RepliesI drove a '97 with the 5.0 and AWD. I noticed that when I turned around in the neighborhood, the steering started to feel a little heavy during a U-turn. I was pretty close to full steering input to the left, but not quite at the lock. Also, it seemed like the tires might be scrubbing the pavement a little bit. No real binding or hopping, just that feel you get when you have the transfer case locked in your old-school 4X4 and make sharps turns. Is this typical for the AWD?
View 7 Repliesi just got an F150 supercrew 5.4L 4x4. has approximately 180k miles but motor and tranny run clean and smooth. issue i am having is the OD light flashes but no other service light is on. i had code read and said it was a Differential Feedback Pressure Sensor (DFPS). Replaced the sensor and hoses but still the light is flashing. i have not changed EGR as of yet due to money but was wondering if i could maybe get pointed in the right direction. the Tranny does not seem to be operating improperly except at low speeds it tends to shift between OD and 3rd on occasion.
View 1 RepliesHave some clunking I can feel through the steering wheel. Starting with checking ball joints.
1999 explorer Eddie Bauer.
Would I jack it up on the control arm to release any tensions? Any tips or tricks after doing a visual to find my clunking?
2000 Expedition. Had ford mechanic replace front heater core due to not having heat in the front and back. wife brings it home I check all vents and notice there's good heat up front but not the back, then I switch the rear from panel to floor heat and hear a thumping sound (figure the blend door is doing it) still no heat in rear. returned to ford mechanic and they stated my blender door switch is not working properly, so they flushed out rear core and instead of fixing the blender door switch they kept it on floor position and charged me another bill. could it be possible that while replacing front core the gunk made it to the rear hoses and core, and clogged it up, and damaged the blender door switch somehow. prior to my heat issues I never had any problems with the rear blender door, just no heat due to front core needing replaced according to them "FORD".
View 1 Repliesthe only thing that is left to replace would be the radiator?my truck is a 1994 f150 and it is not overheating!i get lukewarm heat only on the highway,everywhere else it is cold air!!this new england weather is killing me
View 10 RepliesI cant find my original post but I am reporting back on a low heat output issue. Not the climate door. It was the heater core clogging up. Instead of replacing, this is what I did. Purchased a "drill pump" and some clear hose and some CLR. Cut both the heater hoses,taking consideration of where best to install "T" connectors.
While hoses disconnected,filled heater core with CLR(as much as I could get in it). Hooked clear hose,drill pump configuration,on to the heater hoses. Ran drill pump in both directions for several minutes and stopping and letting it sit for a few minutes.
About 1 hour all together. Pieces of debris came out of the heater core and I could see it through the clear hose. Flushed the heater core out. Installed "T" connectors and it is heating very well now.
with a new heater core, new blower motor, and new resistor and no heat, what would be the problem? gonna check the thermostat tomorrow.
View 2 RepliesMy 2006 F-250 SD with 6.0 diesel has some sort of cut-out for the heater circuit, and possibly for the A/C as well. This truck was probably a fleet vehicle for the Houston Port Authority. Didn't really notice this peculiarity until it got really cold outside. If I start the truck up and let it idle for 10-15 minutes the water and transmission temperature get up to the normal operating ranges but the heater/defrost circuit does not heat up. Cannot defrost the windshield.
If I drive to the end of my driveway, about 600 feet, the heater/defroster starts putting out good heat. When driving, if I have to stop at a stoplight, or any other pause, with the truck still in gear, the heater output starts to cool down. I suspect that this feature was incorporated in the circuitry at the factory to prevent the driver from sitting still to keep warm. The truck MUST BE MOVING to allow heat or defrost to operate. The blower motor operates and it doesn't matter if the truck is in gear or not.