Shifts slowly or stays in shifting mode longer than necessary. Must stop accelerating and wait a few seconds until the shifting is complete. Does something need adjusting?
View 6 RepliesReplaced the 2002 ford explorer 4x4 traction control module because of a shudder in first gear. With the new module the shudder disappeared but now the truck shifts into 4wd by itself and stays there. I am now on my 2nd new module because I returned the first one thinking it was defective.
If I cycle the 4x4 high switch and the 4x4 auto switch, the truck switches back int 2wd but on for a moment then goes back into 4wd. I don't get a 4x4high indicator light but I can hear and feel it is in 4wd. Almost like it thinks the truck needs work with the traction. I have now disconnected the module completely and the trucks runs/shifts beautifully in 2wd. I know my transmission is good. BTW, I have no trouble codes.
Do I have a bad speed sensor somewhere? and How do I trouble shoot for it?
I've just bought a used 2002 Explorer Sport Trac (Automatic) 120k+ odo and what I've noticed whenever I shift from Park to Reverse or to Drive it takes about 3 seconds before I feel a slight jerk moving forward before I can step on the accelerator for the vehicle to move backwards or forwards but if I step on the accelerator right after shifting to any gear except Neutral it won't run immediately as if the clutch is disengaged and after about 3 seconds it will suddenly engage. Is this normal or is there something wrong with the transmission?
View 3 RepliesWhen not using the manual mode of the DSG...What are the differences between driving in D and S? It seems like the car shifts more aggressively in S mode, allowing higher rpms before it shifts. Are their any other pros/cons to the different driving modes when in automatic, And what do most drivers prefer?
View 15 RepliesI have a 2000 Explorer Sport. Sometimes when I start it the "Theft" light stays on. If I kill the engine and restart the light goes out.
View 1 RepliesI have a 2000 Ford Explorer with 188,000 miles on it. I bought it used with 110K miles and put a new tranny in at that time. Now, I am having problems. I don't know if it's the tranny or the engine. It looses power when climbing hills. It takes off really slow with no power and finally gets up to speed it switches gears the whole time smoothly but the engine just can't take a load.
The check engine light came on and put out 10 codes:
P1451 EVAP Control System Canister Vent
P1747 Electronic Solenoid A-Short Circuit
P0743-Torque Converter Clutch Circuit Electrical
P0750-Shift Solenoid "A"
P0755-Shift Solenoid "B"
P0760-Shift Solenoid "C"
P0765-Shift Solenoid "D"
P0135-O2 Sensor Heater Circuit
P0155-O2 Sensor Heater Circuit
P1409-EGR Vacuum Regulator Circuit Malfunction
Those are the codes and I don't know how one has anything to do with the other. I checked the dip stick on the tranny and it's clean. Juicy red and not shavings.
When I got my 2016 back at the end of last October, the pink coolant in the main degas bottle was just visible in the clear top half of the bottle. By the time 5k miles rolled around, the coolant was no longer visible in the clear section. At oil change time, the dealer "topped" it, resulting in it being visible in the tank again. 3k miles later, the coolant has disappeared below the clear part of the bottle again. What gives? The secondary bottle level has not budged. Its clearly not losing a lot, but it is definitely going down slightly.
View 14 RepliesOk so here is my problem now. I'm sure its in the tramny but not sure what else. My shift from 3-5 has always been a little hard. Yesterday on my way to work I noticed shifts 1 thru 3 were hitting hard. Once I got up to 65 mph it was okay. Then pulling into work when I shifted to reverse it didn't go into gear right away and then it would hit into gear. Later that evening on my way home from work it was shifting the same but seemed worse. Then my tow/haul light started flashing and it seemed like the torque convertor wouldn't lock in. It would just stay in 5th gear and the more throttle I gave it the rpms would go up but I would only get a little response from it. Then a few miles down the road it just completely shut off on me. It will not even try to turn over. I could also hear a noise coming from underneath the truck. Something ive never heard before. I really need to figure this out
View 14 RepliesFor the first mile or so on cold mornings, by transmission shifts slowly - sort of a second or two delay until the car warms up. Is this normal?
View 3 Replies2006 Passat, 6 speed manual,113,000 kms. Driving to work this morning and I noticed every few shifts that the clutch pedal rebounded slowly when released. Then in traffic stuck to the floor and I had to physically pry it back with the side of my foot. Worked fine for a few more shifts then same thing again.
View 4 RepliesSometimes mine shifts nice and quick, but sometimes it also shifts soft and slowly with a slight "flare" between shifts. Seems like it shifts better the harder I drive it, but I try not to drive like that. Dealer says everything seems normal to them. Maybe it's the adaptive transmission?
View 32 RepliesMy 2000 Mirage (with 145,000 miles) no longer stays in 2nd gear. Due to the age of the car I do not want to replace the transmission but I would like to get a few more months out of the car. For now I am just shifting from 1st to 3rd. My questions are;
(1) Is there anything I can do short or replacing the transmission to get 2nd gear back,
(2) if I don't do anything to fix the transmission is there any reason I should not continue skipping 2nd gear until something else breaks and
(3) is there anything I should do like flush the transmission to try to extend its life?
ES350 Transmission - I have the following issue that has happened to me twice now.
When it's cold outside (around -10C or below), I start the car and let it run for about 1 minute. I pull out of the parking lot and drive down the street for a very short distance and stop at the intersection and wait to turn left. This only happens when I wait for a minute or more. I go to turn left and the car feels like it has no power and stays in 1st gear all the way up to 4000 rpm and then shifts. After this the car is totally fine and it shifts at the normal 1500 rpm or so going about 15km/hr. When I'm sitting at the intersection waiting to turn, the car is idling at about 1200 rpm or so while the car is warming up.
I've tried many times to recreate the issue but I couldn't do it because I never let the car sit and idle. If it's constantly moving with stop and go it's fine.
I called the Lexus dealer to ask about this and they told me the first thing to do is change the transmission fluid because it could be low or dirty. The car is 6 1/2 years old (July 2006) with 58,000km on it. They said the transmission fluid should be changed at the 6 year interval. They also asked me if I had the car in the shift manual mode (which I didn't) because it seemed to exhibit this behaviour.
My beloved Treg is marooned at the dealer again, having been towed there this morning. Transmission is all over the place...shifts into 5th and stays there, or extremely jerky shifts - especially downshifts. Gear position indicator is highlighted in red and no longer indicates which gear I'm in. Check engine light is on; no message in MFI...
Incidentally, it appears that the dealer and/or VWOA is starting to understand how to treat luxury vehicle buyers. Roadside assistance was very responsive and courteous. Dealer set me up with a rental from Budget...made a point to have me pick something similar to the Treg (not a POS econobox). I'm driving a Ford Exploder...a far cry from the Treg, but at least it's an SUV and has similar seating and hauling capacity.
2007 escape 4wd 3.0. I've notice some random hard shifts for the past month and today the trans has trouble shifting out of 1st. If I get the rpms between 3,000-4,000 and ease off the accelerator pedal it shifts into 2nd without drama. It will not shift at lower rpms with the same easing off the pedal. The trans light is steadily blinking.
View 7 RepliesMy 06 FX4 has 106k it started acting up shifting last week and its driving me crazy not knowing what part to change. Sometimes when I take off slowly from a dead stop it shifts really quickly into o/d by the time I am at 15-20mph. Doesn't matter far as hot/cold but if i accelerate quickly it doesn't seem to do it. I have read it could be the Shift solenoid or TPS.
View 2 Repliesmy wife has an 06 with 77,xxx miles on it. as far as i know there has never been any tranny upkeep done on the vehicle. we have owned the care for approx 15 months. it doesnt act up all the time. it will shift real hard into reverse, feels like it is popping into it real bad. then at times it feels like it slips very little going into overdrive. and at times it will pop when shifted into drive. it is hard to predict, i thought maybe when it was warmed up and the fluid was warm it might not do this, but it does. i know nothing about this thing, the dealer wants me to bring it in so they can plug it in?
View 5 RepliesThis morning was cold. Went to start and it slowly cranked but no start. Tried jumping but again slow crank and no start. Thinking battery charged and tested and it's fully charged. Reinstalled and nothing.
No click.
No crank.
Nothing.
So thinking now. Start with relay.
Then starter solenoid.
Then starter?
Could it be a column thing? Not fully in park or should I try in neutral? Have another thread needing a fuse diagram for inside and the box under the hood.
2003 F250 6.0 ESOF - 4x4 and LOW lights on, TC not shifting
About the truck: 2003 F250 CCLB 6.0L 210k Miles
Heavy Duty Bulletproof Diesel Kit
Warn Front Manual Hubs (vac lines clamped/blocked)
Transfer Case Shift Motor/TCSM is off (I personally have not tested it and am still looking for what to test on it) or I will purchase a new one.
From seller: "What happened is, I accidently put it in 4x4 and when I turned the switch it would not go out. I had to limp it home slowly. When I got home I messed around with it, and could not get it to go back into 2x4. I removed the shift motor, and tested it. It tested ok. I shifted to back to 2x4 with a wrench and left it."
CURRENTLY the TCSM is off the transfer case and is in 2WD. Warn hubs are set to "FREE," seller also noted that this is how he has been driving it for quite sometime. TCSM is in 4x4 LOW, that is what I have to manually shift the transfer case to if I want to mount it up. I have been shifting it using a 14mm open end wrench and with the transmission in neutral. I have not tried turning the TCSM position manually.
Scanning using AE brings up different codes depending on transmission position and which scan is used:
P1812 4-Wheel Drive Mode Select Circuit Failure
P1819 Transmission Neutral Safety Switch Short Circuit To Ground
P1832 Transfer Case Differential Lock-Up Solenoid Circuit Failure
P1876 Transfer Case 2 Wheel Drive Solenoid Circuit Failure
P1865 Transfer Case Contact Plate Power Short to Ground
AE scanning for DTCs: P1832 and P1876
AE scanning using OnBoard System " SYSTEM SELF TEST" with transmission in PARK: P1812, P1832, P1876
AE scanning using OnBoard System " SYSTEM SELF TEST" with transmission in NEUTRAL: P1812, P1819, P1876
AE scanning with TCSM off: P1865, P1832, P1876
P1865 seems to be solved by simply installing the TCSM.
AE Live Data shows correct indicators for 4WD switch, showing corresponding drive mode in AE as the switch setting but nothing happens. No clunk/thud/movement. I have tried resetting the codes but the 4x4 and LOW lights both stay on. I tried it in park, neutral, engine off and engine on. I tried driving 5-10 mph to relieve any driveline wind up, I tried driving in reverse with front hubs free and locked, gave the same results in AE and no transfer case shifting.
Section 308-07A Four Wheel Drive Systems Pinpoint Test I
Found a thread with some fuses to check, I have checked fuses #19, 27, 31, 33, 34, 45 and 111 (with a multimeter for continuity),
Relays (first swapping the old ones, then trying new ones), I did the pinpoints from test I, and installed another GEM (same part number as mine but from a 2005 F-350)
Section 308-07A Four Wheel Drive Systems Pinpoint Test I led to my purchase of a used GEM, not knowing if it is good or bad, I have determined that I get the exact same codes for each AE Scan as the GEM that came with my truck.
I included a photo of my relay box, have any of you seen this type before? There is no other box in the engine bay with twin relays.
Air/Defrost switch works and routes air to switch setting. AC works, DEFROST works.
Could PVHS be causing a code from the manual hubs?
Could the MSS be causing a code even if it is showing correct in AE?
Should I try a new TCSM? Should I try turning the TCSM manually? How do I test, what do I test for on the TCSM?
I want to avoid taking this to the dealer if their own service manual and diagnosis is going to have the same results as my testing.
Where do I go from here?
Could PVHS be causing a code from the manual hubs?
Could the MSS be causing a code even if it is showing correct in AE?
Should I try a new TCSM? Should I try turning the TCSM manually? How do I test, what do I test for on the TCSM?
A couple of weeks ago my amp went out and it was replaced. I didn't use the USB port previously b/c my MP3 player is old and wouldn't connect. However after having the amp replaced it dawned on me I could use my phone (motorola cliq) to play music with the USB. It worked for a couple of days and then nothing. The tab on the mode options for the USB would no longer light up. I can still play music from my phones SD card via the aux and via bluetooth, but not the USB. Took the car back in and two days later they are telling me its my phone. Maybe, but considering it worked prior and nothing has changed on my phone I am at a loss.
Today, they called to tell me they were able to hook it up to a ipod and everything worked great! Mine DID work, so what changed? They suggested I use a stick/thumb drive. Went and bought one, loaded one album onto it and it won't work either. The USB tab won't even light up for me to choose it as an option. I do NOT want to go by a ipod when I have a perfectly great 16 g sd card in my phone that DID work! But I also want to use my touch screen to choose songs and go through my music files without having to use my phone while driving. The USB port is recognizing my phone as it charges it while plugged in. I have tried setting the phone to SD card on, and then off (charge only setting). Nothing causes that USB tab to light up and give me a choice to see whats going on.
Started the car this morning and I noticed on the head unit that the drive mode selection wasn't showing "Comfort", "Sport" "Normal". When I press the mode button, the choices are faded and can't be pressed. Is this common? Something I've done?
View 4 Replies