Ford - Explorer :: 2000 - Making Bearing Noise?
Aug 13, 2013
2000 Explorer making what I would call a bearing humm. I have replaced both front wheel bearings over the past year. When I jack up the front and check for play everything is tight, I don't get any noise by spinning the tires. While driving I put the tranny in neutral and still get the hummm sound, so I don't think it is the tranny.
The sound definitely changes with the speed of the car. Turning the wheel or engaging the transfer case do not change the sound. I have had my son crawl around the car while I'm driving and he said the sound is not coming from the back, for sure the front but can't tell if it is specific to one side of the other.
Where do I go from here? This is my daughters daily driver and its been a great car, 148000 miles and no issues at all so far. I would like to figure it out so I can feel good about her driving the car.
View 12 Replies
Advertisement
Its getting worse. Noticed it a month or so ago, very slight ticking noise when the engine was cold. It would go away after a minute or two when the engine warmed up. Kinda sounded like a lifter ticking type noise when low on oil but I was not low on oil.
Now its getting more noticeable and it doesn't go away. Very noticeable when I take off or accelerate. less noticeable when I take my foot off the gas but its still there.
What it might be? I am pretty newbie about engines and I don't want some repair outfit telling me I need a rebuilt engine if all I need is to tighten my manifold or something. Because that would be my luck.
2000, XLT, 5 Liter V8, 178K miles.
View 5 Replies
Wheel bearing go out? My left front just starting making noise and when turned by hand you can hear the bearings are shot. Called around this morning and with my luck its on back order and the entire hub has to be replaced since the bearing is built into the hub.
Anyways, I was wondering replacing this unit themselves and how long it took to complete? I was going to let Ford do the work but I figured I have never done a job like this and wanted to give it a try and looking at some Youtube videos on older vehicles it did not look that difficult.
If I find that its not difficult I will tackle the other side as well since I figure it is probably not long before that side is gone also and I would not want that to fail while I am out towing somewhere.
View 8 Replies
I have a 2000 F150 XLT 5.4L truck. I noticed the AC went out about a month ago and since then I could hear the AC/Clutch bearing making noise. Well I went to start it the other day after eating dinner out and it wouldn't start. It sounds like it wants to start but it just doesn't have enough umph. I replaced the starter and charged the battery up to 100 percent. It still won't start.
If I take the belt off it will start and I checked the AC/Clutch and I can move it with my bear hands. I tried disconnecting the AC/Clutch fuse and relay but that didn't work. Is it possible that the Clutch is freezing up when I try to start it?
View 3 Replies
Have a rear wheel bearing making some noise. A friend told me that it is always the outer bearing that goes first . Can you replace the bearing without replacing the race?
View 14 Replies
The T/O bearing makes a high pitch squeal until you put light pressure on clutch then it will go away. Does this thing have a preload on bearing at all times or should there be free play like in the old days??
Another thing that has me wondering is when I push clutch all the way in it actually puts a load on the engine. Having T/O bearing so bad it puts a load on the engine?
View 2 Replies
I have a 03 explorer with approx 160k, I am experiencing a thumping noise while driving. It gets worse on right turns and gets better on left turns. initially i thought LF wheel bearing so i ordered a hub assy and replaced LF. noise is still there. I guess, thumping noise caused by wheel bearings, i know its usually a grinding kind of whirring noise.
The noise doesn't seem to change with accel/decel so I don't think it is driveline related (diff, drive shaft etc.) should i bite the bullet and replace the rf as well??? I should also mention that there is also a shake in the steering wheel that seems to coincide with the thumping (i.e., my hand shakes along with the thumping, and the shake gets worse when the noise does)...
View 8 Replies
I have a 2003 Sport Trac 4wd with 299,000 miles. There is what sounds like wheel bearing noise (grinding) that was noticed after returning from a trip where I flat towed it behind my rv. I did not notice the noise the last time I drove it - before towing it about 450 miles. I have towed this vehicle for many years and miles this way - transmission and transfer case in neutral with key in on position to unlock steering. I stated this part about the towing because the noise may have gone unnoticed for many miles. About 20,000 miles ago, I changed front wheel bearings, brake calipers, upper and lower ball joints, shocks and outer tie rod ends. Also rear brake pads.
I put the vehicle on jack stands and in drive mode couldn't hear anything in either 2wd or 4wd. I held one wheel at a time so the other side would spin. After checking for wobbling wheel bearings, I took off the wheels and did a push / pull on everything - all seems good. I changed driver's side wheel bearing anyway because I thought it to be a little rough. I removed the front drive shaft and took it out on the road. Noise was still there. This makes me think front differential but before entering unknown territory (for me) is there something else I can do to narrow down the problem? At this point, I'm not even convinced it is from the front end - maybe the sound is radiating through the truck.
View 3 Replies
I'm working on a 02 explorer. The front end is howling so I replaced the left side and no change. The howl goes away when braking. Is it the right side then or something else? I replaced both front brakes pads so it's not that.
View 2 Replies
I have a 94 Explorer. I recently swapped over from auto to manual hubs. I followed a detailed write-up that I found online. During the process I repacked my outer wheel bearings. Ever since then I hear a grinding noise coming from the front wheels. Sounds like the bearings aren't seated properly. The guide that I followed instructed to torque the spindle nut that sits next the the outer wheel bearing really tight in order to seat the bearing, then loosen it back up and hand tighten it. But when I loosened the spindle nut the wheel bearing would pop back out. What is the best way to get a wheel bearing to stay seated properly?
View 2 Replies
So my front right Wheel bearing is making noise and its a used Knuckle so its w/e. Guess ill use tonight to do all my bushings and fluids n stuff.
View 6 Replies
I have a 2009 Camry 5spd with 92K miles on it. Camry is completely stock and original with meticulous services to engine oil and drained the transmission fluid at 68K miles. I am hearing an engine hum every now and then (although I notice it more often now that I am searching for it) while I am idling. I don't believe it to be engine vibration, rather it is a hum, seems like a belt pulley bearing is going out, or even, and i hope its not, like my throw out bearing in the clutch is going bad.
Only reason I say that is because it makes the hum for a few seconds then goes away, then comes back for a bit. It makes the hum when i have the clutch engaged and when i have the clutch disengaged and a in neutral. I have opened the hood to try and search from where it is coming from but it is just too darn hard to figure out.
I am hoping it is nothing related to my transmission. I may pull the fill plug on it this weekend and try to stick my finger inside to see if I am low on fluids and it is making a hum (but I highly doubt it because when I filled it up after drain i filled it too the top). I haven't experienced any burning of oil and use 5W-20 (Castrol GTX since day 1). I may switch fluids on my next change and use maybe a different brand and viscosity (maybe use standard Quaker state at 5W-30).
Again it isn't an engine vibration, rather just a hum or almost like a stinking wobble and then goes away for a few seconds. I say wobble kind of like you would hear a drive shaft on a truck that wasn't balance properly and was spinning without being centred with counter weights.
View 1 Replies
Immediately after I had four new tires installed on a 2000 Blazer 4wd, the front wheel bearings started making noise. At the time I thought the noise was from the new tires. A few thousand miles later my mechanic told me I needed two reman hub assemblies (sealed bearings) for ~$350 apiece plus labor.
Is there anything that the tire shop (independent not chain) could have done (accidentally or otherwise) to damage the bearings during the tire installation? I have to get 4 tires for my 93 Chevrolet Caprice and don't wish to repeat the experience.
Whoops, forgot to mention this happened at 56k miles when the truck was five years old. Is it possible that the bearings were borderline and the process of mounting the wheels put them over the edge? For instance, someone being a little over enthusiastic with an impact wrench.
View 4 Replies
My throw out bearing makes a faint chirping noise since I bought the car, but now that the weather has been in teens, it seems to be louder.
I was wondering if it is possible to grease the throw out bearing or something without dropping the transmission.
View 1 Replies
I have a 2001 Toyota echo 2001 210.200 km and my output shaft bearing makes noise and I cant know the level of my transmission fluid bcoz I don't have dipstick and i bought trans 75w90 oil os that ok and how can I add this?
View 1 Replies
My exlporer heat and A/C system has been making "ticking or flapping" noises for sometime. So, to make it stop I would turn fan to full blast and it would stop and the heater would function fine after that. Last week we hasd a warm spell and I switched to A/C (going through the same process to stop the noise). All was well until I tried to switch back to heat after the warm spell, and now I get nothing but cold air. The noise will only stop when I turn the temp dial to the cold side, but either way, all I get is cold air. Is this something I can fix, and if not what am I looking at for repair cost? I'm freezing!!!
View 3 Replies
Asking on behalf of the woman who picks up my kids from school and drops them off at after school care. She has 2005 explorer and says the brakes are making noise while she is rolling. noise stops when brake is applied. she thinks it is coming from the front. I said I would check it out. I've owned a few trucks but never messed with an explorer.
View 1 Replies
I have a 2014 Explorer Sport and I'm having problems with cranking. On really hot days when its 90+ degrees, my explorer will make a clacking noise when cranking. When its 100 degrees, the first try on cranking will give the same noise, turn over and not start. On the second try, it will start. The odd thing is, after it does crank, it will crank normally when I try it again. After waiting a few hours, the same issue will occur again. I'm thinking this may be a starter issue. I will take a video and post later.
View 6 Replies
I have a 1996 Explorer XLT 4x4 and I hear what I call barring making a noise when I accelerate. If it is the bearings in the rear end how expensive is this to fix? I love my truck but I'm on a fixed income and scared to death. I will not drive it until I get some sort of idea as to what and where I should take it.
View 2 Replies
I own a 2002 Ford Explorer and I need diagnosing a problem. Whenever I start to pick up speed it starts to buckle and I always have the 4x4 on auto and it still buckles.
View 1 Replies
For the last few weeks, when I make a turn (particularly a sharp turn in either direction) I get a "clunking" noise that sounds like it is coming from the front end somewhere. I can also feel it - almost like a gear slipping and engaging again. I am not in 4WD mode when this is happening. It NEVER happens unless I am turning a corner. If I drive straight, it's fine. 1999 Explorer XLT (4 door, 4wd model)....
View 2 Replies
