Ford - Explorer :: 1999 V8 - When Changing Into 3rd Gear RPMs Will Keep Rising
Jun 6, 2012
its a 99 explorer xlt AWD 5.0l v8. It has the AODE/w tranny. When I take off with it (normal accelerating) it shifts fine from 1st to 2nd. But when it is suppose to change into 3rd gear the rpms will keep rising as i give it gas. When I let off the gas it goes into neutral. I plan on changing the fluid and filter in it. But need to know if there is anything to check in the valve body before putting new fluid back in? This problem has come at a bad time for me.
View 4 Replies
Advertisement
Having problem with air suspension lowering and rising without changing any settings? Is this normal or maybe I have a leak in my system?
View 10 Replies
The other day, my Explorer gave a hard jerk while changing into 2 (maybe 3rd?) gear. Never happened before. I was under 20 MPH & had just stared it. (My speedometer works as do all the dials.) My Check Engine light came on & when I had the code pulled it read quote "P0715."Transmission Speed Sensor circuit condition. Vehicle speed above 15 MPH while transmission output shaft speed below 60 RPM. Possible cause Failed transmission speed sensor or electrical problem"
I got a Transmission Speed Sensor, (which I haven't put in yet), and was told that this would solve the problem. My question is twofold: Is there ANY chance this is a false or misread code and the problem is something else? And could ANOTHER sensor attached to the transmission be the cause? (How many sensors are on the tranny?) All I've read about this problem, say's replacing the Transmission Speed Sensor is preceded by the SPEEDOMETER quitting, but mine works fine.
The truck is a 1997 Explorer 4x4, but I don't use 4x4. In fact I've driven it without the forward drive shaft ever since I had the BW4405 Transfer Case replaced.
View 8 Replies
I was driving down the road tonight and have been hearing a hissing sound when accelerating and when I went out to get it audio of it to send to the VW dealer, I heard a loud noise, and now it sounds like I don't have an exhaust, the rpms aren't raising no where near what they should be, and have a gaseous smell.
View 14 Replies
My 4.65L V8 Explorer has an issue in low gear - RPMS rev high but car doesn't shift up.. eventually "catches" with a jerk but the OD Light started flashing and the Systems Screen reads Check Transmission. Light goes out and message goes away after turning car off and restarting. Had one Tech look at it - he said second gear is toast and need full transmission rebuild. Another Ford Tech looked and could just be solenoid needing replacement and advised to have a transmission service (not a flush) done....
View 2 Replies
I have a 99 f250 with some procomp (325s) that are 12.5 wide with a 6in lift my superchip tuner can change the trannys shift points but I am pretty sure a new gear ratio is needed. I dont do a whole lot of off roading with it its mainly my driving around and highway rig whats a good gear ratio that would work for me
View 9 Replies
My 2000 f250 7.3 4x4 with a 4r100 tranny. I was towing my boat home and noticed the temperature rising from roughly 140 all the way to 160 over a short distance. As soon as I pulled up to the house I noticed I was dumping my transmission fluid. Went to a mechanic and he fixed the leaking on the transmission by replacing some seals and changed out my rear main seal while the tranny was out.
I also went ahead and replaced the torque converter so I would not have to do it in the future. went to pick up my truck and noticed that on the way home the temperature was still rising. On a normal day here in Texas my tranny temperature was about 125 While towing it would creep up to about 143. Now, just getting home it got up to 180. What could be causing the temp to run this high and keep climbing?
View 14 Replies
1999 Explorer starts then will not idle unless it is put into gear. It only happens once in a while...
View 2 Replies
2003 F250. 6 speed. 5.4 2v. 4x4. 165,000 miles
When purchased, there was a vacuum leak and truck ran like crap and PO drove it that way for a while. I fixed the vacuum leak, discovered a miss between 1,500 and 2,000 rpms in every gear while accelerating. No miss at idle.
The truck has:
- no CEL
- new Motorcraft spark plugs that were not dropped, bumped, or over torqued.
- new fuel filter
- new air filter
- new alternator
*The miss usually does NOT happen in the morning on the way to work after sitting 14 hours.
*The miss almost always goes away after the truck gets up to operating temp.
*The miss ALWAYS is present after work on the way home after sitting 9 hours.
Fuel pressure?
Bad COP?
Fuel Injector?
Something totally different?
View 14 Replies
I go out of town for work for a week and come back and my 1999 F250 V10 GAS, is acting up. It started when i tried to drive it and it didn't want to shift, it would rev up to 3000+ RPMs and finally shift really hard into gear along with the speed odo not keeping up and bouncing around not wanting to work. I also had my entire gauge cluster lit up with no key and door closed. all the lights were on and it was "dinging" like the door was open and it wasn't. you would hear it when you put your ear up to the door.
So my first thought was to change the VSS (which I did) no luck. So I started wiggling wire loops under the fuse box in the cab and the "dinging" quit.. i took it for a drive and it works like nothing ever happened. Obviously I am guessing there's a short so i brought it to my mechanic and hes saying he couldn't find anything by the fuse box but he thinks its closer or even attached to the gauge cluster itself. could this be true? Why would the gauge cluster loop throw off the shift points?
View 5 Replies
I have a 06 f350 with 5.4 140k miles. Recently it has been shaking bad on idle but only in gear and it's hard to start when cold. The exhaust is moist at all times and the fluids never leak. When you floor it it hesitates feels like it's overly rich but if you let off a little it stars to pull again. Also while cruising at 1500-1700 rpms in any gear it will surge and skip. Only time it will miss and the CEL comes on is over 4000 rpms for a random misfire. Just put new coils in new fuel pump and filter. There has always been a cat code but it never effected the drivability. Could it be injectors?
View 3 Replies
My 02 Explorer with the 4.6 has about 100k on her and I think it is time to change the coolant. ( I have only had it since 87k )
Should I flush it or just change it. What is the best way ?
View 6 Replies
My friend is changing out the ball joints, upper and lower, both sides. I have seen that the upper is typically done by replacing the whole arm, I don't plan on doing this. So, with a press and new ball joints, are there any nice tips from you all? Looking for useful info before I get into it. I did a search and have not found a thread like "ball joints-how to".
View 7 Replies
I have a 2002 Explorer that had a whining rear, changed it out with a good rear out of my parts truck and now I have an ABS light on. It says something about input to the sensor and output from the sensor and left and right wheels. 4 Codes in all. I changed the speed sensor in the top of the rear to the one that was in this truck because the light wasn't on before and it still has this light.
View 1 Replies
I have a 02 Explorer that has 2 cracked rear coil springs.
How hard are they to change ?
What brand to use ?
I was looking at the Monroe Quick-Strut.
View 14 Replies
I'm in the process of changing my upper and lower intake gaskets. my question is, the upper intake along with the tubing on the fuel rail are caked with oil/carbon, along with the back side of throttle body. What would be the best way to clean them?
View 2 Replies
I have a 2000 explorer XLT and I want to change all of my interior lights to blue. I want the cluster, window switches, a/c unit and everything else blue. I just bought a blue stereo so that's one less thing. What types of lights and how many lights there are and where I can get them and how to change them?
View 1 Replies
I drive a 1998 B5 1.8T passat. This happens when i go up a hill, i mean i can go up the hill fine but then when I go straight my rpms go crazy before changing gears, idk if this is normal but I doubt it.
View 9 Replies
I own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.
View 4 Replies
I have a 2002 Ford Explorer and besides the seemingly oh-so-common annoying crack in the tail gate, I have another issue I consider to be major. Recently, on a short trip to the store, I hit an incline in the road of a slight degree. At this point I noticed the RPMs going wildly up and down and ultimately the truck died. I tested this out on a few drives and what I've noticed is that if I'm on a flat surface, the truck seems to be okay. OR if I do hit an incline, either lifting of the gas or powering through it seems to work...although neither of which is a long-term solution. I just lost my job a couple weeks ago and the idea of taking it to a mechanic scares me as I'm very limited on savings. I don't really know where to start.
View 6 Replies
I have a 1996 Explorer XL 2 dr. It has the 4.0L OHV V6 and the 4R55E Transmission. I bought it used with 152,000 miles on the odometer. About a month after I bought it I noticed it sounded different. I looked down at the tach and the RPMs are up around 2500 with the overdrive engaged. I turned the overdrive off and nothing changed. I turned it back on and nothing changed.
That weekend I pulled the tranny pan and filter and replaced the filter and fluid. There was the normal amount of debris in the bottom of the pan but nothing major. Now when I drive it it tries to shift into overdrive but when it does the engine bogs down and the O/D off light starts flashing. I know how to do the overhaul but I wanted to get a few opinions before I start tearing into it. What could be wrong .
View 1 Replies
