1999 explorer Eddie bauer. Front wheel bearing nut size? 33mm?
Looking for a torque spec procedure. Need to replace an abs sensor. Sensor alone was 120 bucks so just bought the whole hub assembly with sensor. Might just put the whole thing on.
Is there a good thread for a complete socket size portfolio on the explorers. Thinking sizes over and above normal socket sizes found in your typical socket set?
I have a 03 explorer with approx 160k, I am experiencing a thumping noise while driving. It gets worse on right turns and gets better on left turns. initially i thought LF wheel bearing so i ordered a hub assy and replaced LF. noise is still there. I guess, thumping noise caused by wheel bearings, i know its usually a grinding kind of whirring noise.
The noise doesn't seem to change with accel/decel so I don't think it is driveline related (diff, drive shaft etc.) should i bite the bullet and replace the rf as well??? I should also mention that there is also a shake in the steering wheel that seems to coincide with the thumping (i.e., my hand shakes along with the thumping, and the shake gets worse when the noise does)...
My wife's Explorer 4x4 has a noise in the front at around 100km/h. It is not detectable below 90km/h. Its not noticeable from a standstill until around 100, then you hear it a little. I find I can make it more noticeable if I vary my speed from 110 to 105 up and down, then its easier to hear. Once you get below 90 km/h you cant hear it at all.
I have a broken leg right now, and I normally do ALL my own work so I'm a little-limited mobility wise at the moment.
I'm suspecting a wheel bearing. I put the Explorer in the garage and my son jack up both wheels on the drivers side. I started the engine and SLOWLY accelerated up through the gears to 100. I know the hazards with this as I've done it with other vehicles, but this was the first 4x4. Then we jacked up the passenger side (after lowering the drivers side) and did the same thing. I could slightly hear/feel the rumble when the passenger side was jacked up.
I did drive the vehicle on my outdoor ramp/pit so I could use my crutches and get underneath to have a look. I grabbed the cv axles and they feel solid. The propeller shaft was replaced last year, and the cv axles look brand new. (bought the vehicle off a friend two years ago.).
So, are my suspicions correct, is it the pass. side wheel bearing? The Explorer has 294000kms. Never did test it on corners as I didn't want to swerve back and forth on the highway with the amount of traffic.
I'm working on a 02 explorer. The front end is howling so I replaced the left side and no change. The howl goes away when braking. Is it the right side then or something else? I replaced both front brakes pads so it's not that.
View 2 RepliesI have a 94 Explorer. I recently swapped over from auto to manual hubs. I followed a detailed write-up that I found online. During the process I repacked my outer wheel bearings. Ever since then I hear a grinding noise coming from the front wheels. Sounds like the bearings aren't seated properly. The guide that I followed instructed to torque the spindle nut that sits next the the outer wheel bearing really tight in order to seat the bearing, then loosen it back up and hand tighten it. But when I loosened the spindle nut the wheel bearing would pop back out. What is the best way to get a wheel bearing to stay seated properly?
View 2 RepliesI was getting a growl/grinding noise from my front hubs (driver's side I think) when I do a slight right turn like going around a curve, not turning around a corner. Just started happening the last week after returning from a 4th of July roadtrip. First thought was wheel bearings going out and started reading up on the forum here to see what was needed. Last night, I started getting a continuous growl when I was 5 miles from the house so just pulled up and parked it. I'm assuming (without pulling anything apart), it's the bearing assembly and I can get the Timken version at Autozone locally.
The problem is I generally do my heavy maintenance at our family shop in San Antonio but I live in Austin so will need to do this in my driveway. I have all the basic tools, just need to know how involved it is to do in a driveway instead of a shop. Thoughts?
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies1999 F250 CCSB Lariat 5.4, 2 wheel drive. I plan to replace the Driveshaft Center Bearing in the next few days. What size is the Nut that I have to remove to remove the yoke next to it so I can press the bearing off?
View 4 RepliesI have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 RepliesWell, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
I have a 2003 F350 srw 6.0. 4x4. Front driver side wheel bearing went out. Went to the auto parts store got a replacement. Got it all tore apart, put the new one on and the lockout didn't seem to fit right. Is there a difference in wheel bearing assemblies for electronic shift on the fly and regular lockout? I have the electronic shift on the fly lockouts and it had just a little bit of play in it when I put the snap ring back in.
View 3 RepliesI am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 RepliesI have a 2003 Sport Trac 4wd with 299,000 miles. There is what sounds like wheel bearing noise (grinding) that was noticed after returning from a trip where I flat towed it behind my rv. I did not notice the noise the last time I drove it - before towing it about 450 miles. I have towed this vehicle for many years and miles this way - transmission and transfer case in neutral with key in on position to unlock steering. I stated this part about the towing because the noise may have gone unnoticed for many miles. About 20,000 miles ago, I changed front wheel bearings, brake calipers, upper and lower ball joints, shocks and outer tie rod ends. Also rear brake pads.
I put the vehicle on jack stands and in drive mode couldn't hear anything in either 2wd or 4wd. I held one wheel at a time so the other side would spin. After checking for wobbling wheel bearings, I took off the wheels and did a push / pull on everything - all seems good. I changed driver's side wheel bearing anyway because I thought it to be a little rough. I removed the front drive shaft and took it out on the road. Noise was still there. This makes me think front differential but before entering unknown territory (for me) is there something else I can do to narrow down the problem? At this point, I'm not even convinced it is from the front end - maybe the sound is radiating through the truck.
So on my girlfriends 2000 echo I get the classic bad wheel bearing noise/vibration on the front left (driver side) wheel. Worsens under load (right turn) and goes away when unloaded (left turn). I've replaced left side bearing, CV axle, brake rotors/pads and the noise still persists. My next thought is maybe the ball joint but humming/vibration tells me something out of rotational balance. Bearing in the transmission? I don't know. I'm stuck.
View 5 RepliesThis past week I changed out the front wheel bearing hub assemblys on both sides. I'm curious if completely disassembled one of the units? If so what did you use to get the large nut with the 4 notches in it off?
View 2 RepliesWhat is causing the right front wheel bearing to keep going bad on my 06 f-150 2 wheel drive....
View 1 RepliesSo just as I think I have it figured out what size tire and wheel combo I want to go with, I began thinking about going from an 18" wheel to a 17". I can save some cash, have a few more tire size options and save on tire weight.
I know alot of guys go up to a 20" setup but that's just not my preference on trucks.
Any negative to doing this? 315/75/17 tire size interests me. Had that on a Wrangler and liked the look. Going to look a little more at 17" sizes before deciding.
I have been having towing with the X. I have been getting a growl lately sounds like the front left wheel bearing. Today I jacked it up and did the wiggle text. I have a very slight wiggle in both wheels. Is a slight wiggle normal? I know the bearing on the left is more than likely gone as the growl goes away when I jerk the steering wheel. But I haven't heard any noise from the right side yet.
View 14 RepliesWhat is the size of the nut that needs to be removed so I can pull the carrier bearing off the drive shaft? I need to purchase a socket.
View 14 RepliesRepeat Front Hub Failures -- 2WD Try this situation -- Purchased 2006 F-150 XL with 57,000 miles. Truck built on 05/24/2006.
Sept 2011 68,621 miles -- Left front hub failure -- Wheel bearing grinding -- Done by Bell Ford in Phoenix.
2013 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2014 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2016 -- Upper & lower control arms, struts, strut mounts, springs replaced -- Quality part used -- Complete front end alignment -- Brake job front and rear.
Nov 2016 -- New performance exhaust system due to exhaust leaks.
Dec 2016 -- Failed automatic transmission -- Remanufactured FORD transmission installed w/ 36 mo warranty. Sanderson Ford gets an A+
March 16, 2017 151,000 miles -- Left front hub failure -- wheel bearing grinding! Verified by jacking up truck and spinning left front wheel -- GRIND! This is coming from down in the hub. This is a 2 wheel drive truck. Yes, you counted correctly, this will be the 4th replacement on the Left side!
NO Towing! NO Overloading! Wheels are 2006 XLT style Aluminum rims with P235/70R17 Michelin XLT M/S (Defender LTX) tires all around.
It only hauls maybe 200 to 300 pounds of electronic equipment at the max, once in a while. This is driving me crazy! I always use FORD PARTS for the HUB ASSEMBLIES. Really loosing faith, the front right hub is OEM original - NEVER CHANGED!