Ford - Explorer :: 1999 - Check Engine Light Keeps Coming On / Misfire Code
Jun 30, 2014
I have a 99 Ford Explorer - w/217k miles. (2nd owner) .. I got an oil change 3 weeks ago, tune up 2 mos ago, and new brakes/tires within the last 6 mos, oh, and Brother-In-Law just recharged my a/c last week.
Runs well, and I hope to keep it for another few years, but having problem lately.
Check Engine light keeps coming on - I've taken it in, and they read the code, and it comes up with a misfire. Mechanic resets it, and it will stay off for a few days/weeks, and then comes back on.
View 3 Replies
Advertisement
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 Replies
My 2007 Explorer (XLT, V6 4.0L, 4WD, 175k miles) has been experiencing a check engine light, intermittently, for the past few months. I took it to AutoZone to read the code and they gave me a printout for P0193. For awhile, the light would go off after I filled the tank with gas (usually the next day) and would come again as the level in the tank decreased (typically around 1/4 of a tank). Then about two months ago, the behavior seemed erratic and I could no longer predict when it would appear. During the past couple of weeks I only recall seeing the CEL once (briefly); it's mostly been off. Saturday night I was out driving and it came on again.
About two hours later, my vehicle "conked out" on me. It started hesitating (it's been a very long time since I've run out of gas, but that's what it reminded me of). Fortunately, there was no traffic and I was able to get it off the road but didn't have enough momentum to get it into a defined parking space before it quit. I sat there for awhile pondering my options (not too many since it was the middle of the night and I don't have road service). After about 10 mins or so, I decided to see if I could get it started. It did start and I was able to drive it home (< 10 miles). It's been sitting in the driveway since because I'm afraid of getting stranded if I drive it again. BTW, I was low on gas when it died -- about 50 miles to E (was headed to the gas station when it happened, but took it home instead).
After everything I've read the past few days, I'm expecting that I need to replace at least the fuel filter, the fuel rail pressure sensor and the intake gaskets for the manifold. I am not a mechanic, don't have diagnostic tools, my funds are really limited right now and I'm pretty much on my own to figure this out.
Q1: For those who may have some knowledge about this particular issue, does the intermittent nature of the CEL give any clues to which part(s) might be malfunctioning?
Q2: I found a replacement FRPS made by Bosch on Amazon, significantly cheaper -- is this brand ok or should i stick to Motorcraft?
Q3: Any advice on the manifold gasket replacements (is one brand better than another)?
Q4: Do I really need the special tool to replace the fuel filter?
The questions above are no longer relevant. I'm in the process of "locating" the sensor. I have the air hose and throttle body off. Now I'm looking at the EGR valve. It looks like I will have to disconnect the it from the large pipe beneath it. Will I also need to remove the two smaller bolts that mount it to the manifold cover, or can I remove the cover & valve together? It looks like those little buggers are going to be challenging since they are facing the back of the engine compartment. This is rather slow-going for me, but there's no turning back now.
View 4 Replies
I have an 01 Explorer Sportrac with a 4.0, 105,000 milles. Got the check engine light with the EGR low flow code. I get this code about once a year and a new DPFE usually takes care of it. I get the sensor from Advanced Auto which explains the short life I am guessing. Last time i replaced the sensor the light came back on a couple weeks later.
After highway driving smoke starts pouring freon under the hood, passenger side, but by the time I get the hood opened its done. Cant tell where it is coming from. Could a faulty DPFE cause the smoke or do you think the EGR valve may be sticking? I was going to try a Ford DPFE this time but I hate to just throw parts at it. Where do the smoke is coming out of, air filter box????? cant see anything else over there related to the EGR system......
View 4 Replies
1997 Ford Ranger with 190K miles has check engine light on with P302 computer code, meaning misfire on cylinder 2. Engine runs rough at idle only once it warms up, which only takes a minute. It is usually fine while driving, but it's a lot easier to feel a misfire at lower RPMs than at higher ones. Added fuel injector cleaner to gas for a couple tanks, no change. My mechanic has checked spark plugs, fuel injector, o2 sensor, and everything is ok. Dry compression test shows good compression. He thinks it may be a valve sticking, which means a valve job: expensive. Is there anything else that can be done? Why is there no misfire when it is first started?
View 9 Replies
2004 Sports Trac Got a check engine light: a code P0913. The truck , once in a while, hesitates like it not getting fuel. Is this a fuel pump problem or something else?
View 1 Replies
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 Replies
I have a 2007 Toyota Prius with just under 30,000 miles. Yes, I don't drive all that much, which makes the Prius the perfect car. I get it serviced every 6 months by the dealer. So far, other than oil changes, the only actual maintenance has been tires, a 12 volt battery, and a $300 "inspection".
A few weeks ago the "Check Engine" light came on. I pulled the code P0301, which translated to "Misfire on cylinder 1". The car was running great at that time, and since clearing the code it has continued to run without the light coming on again. Given that my maintenance is more time-related than mileage-related, it's possible that the ignition system needs attention. However I'm reluctant to bring that up at my next maintenance appointment, because the guy writing up the service order will always answer "Yes" to every "Do I need ..." question.
View 2 Replies
I bought my 2008 Prius 9-14 with 29,000 miles on it. (rebuilt title-big mistake I now know). I found out after I bought it that it had sat for 5 years before it was rebuilt) I figured it was a miracle the hybrid battery even worked.
I had no problems until 2-4-15 when check engine light was flashing and the car was shaking. The local mechanic said was the “clutch” (torque converter), took the engine and transmission out of the car to fix it ($2200). But he realized the mass air flow sensor (MAP) was not working even after he put a new one in so had me take the car to the Toyota dealer. The dealer found a cut in the engine harness and advised me to replace the harness which he said would cost $2800. The local mechanic saw the cut via my cell phone photo and offered to fix it for free which he did.
The next day check engine light comes on after driven 25 miles with code PO 301. (means misfires in cylinder one). The local mechanic switches cylinder 1 with 4, same code the next day, local mechanic switches the coils to the cylinders, still the next day the same code. He switched the fuel injectors. Same problem of cylinder 1 misfire. He cleaned the oil out of the intake manifold, did fuel injection cleaning, and cleaned gunk out of the fuel line. Car would drive good about 20 miles then same check engine light, same code, sometimes code PO300 (random multiple misfires).
View 19 Replies
(This is a continuation of a previous thread: [URL] ..... )
I have a 2005 Nissan Sentra with 75,000 miles on it. Several months ago (see above link) the check engine light came on with a P0304 cylinder 4 misfire code. The only symptom appears to be a rough idle/shaking every 3rd or 4th start for the first 10-15 seconds, but runs smoothly afterwards. My mechanic replaced all my spark plugs (I had new plugs put it at 50,000 miles for the same issue) of which the one from cylinder 4 was worn down much more than the rest. The problem persisted so they replaced my fuel pump and fuel filter and switched the spark coils from cylinder 4 to a different cylinder, but the code still read cylinder 4 so it wasn't the coil. That was back in October.
I took my car back in last week for the same problem and without starting my car (because the problem is worst on the first start) they pushed my car into the bay and did a smoke test, no leaks in the fuel lines. Then they checked the cylinder and said that there was "excess" fuel in the cylinder and replaced the fuel injector. Then after ~3 days the check engine came back on with the same P0304 misfire code. Previous repairs/diagnostics rule out spark plugs, coils, fuel pressure, and injectors.
View 19 Replies
In the last month, my car has had an awful time starting on 2 different occasions. The first time it ran really rough for about 1 minute then was ok. The second time was the same but the engine light came on. Took it to an out of town dealer and he said it showed a misfire code but could never find anything else and all looked OK. Spark plugs?
View 4 Replies
I own the 2014 Santa fe turbo 2.0 litre limited which has 4000 km on it. Within 210 km the engine light came on 3 times. I took it into the shop and they ran a code of P0303 which is a misfire, they changed the coils #2 and #3 and cleared the code. The second time it showed the same code but the shop said it was in the history so that is why the same code came up again. They ran an update ECM? and all was good. Now the 3rd time they tell me no code has come up and can't do anything about the engine (they cleared it) but it was like chasing ghosts. My vehicle runs great so not sure why I am constantly having this issue.
View 68 Replies
2000 Tacoma v6 has has always ran good, but has check engine light code P300 & P306. cly 3 & cly 6 missfire, lean bank 1. Vacuum test showed no problems.
I've changed plugs & wires, switched coils around cleaned mass air flow sensor, checked timing. Ran Seafoam through intake, and gas tank. Check engine light went out for about three miles, then came back on. What else can I do to keep that blinking check engine light off?
View 1 Replies
What are the common misfire problems with the mk4 R32? My R is acting funny every once in a while it runs perfect then some other times it seems to big and the check engine light starts to blink but doesn't stay on I ran for codes and it said I had a miss fire but after that the code never came up again but it still blinks.
View 7 Replies
I know it is a random cylinder misfire code however I started my car in the morning and it was fine I moved it and put it back in my driveway. I started it up later and waited for it to heat up i came back outside 10 min later and my check engine light was flashing and my car was shaking like crazy you could tell the engine was misfiring like crazy. I had under a quarter of a tank but not empty yet. I shut it off and turned it back on and it was still doing it. I drove the mile to the gas station the way it was.
Under partial throttle it was revving to 4500 and over 5, had to let of throttle to make the car shift up a gear. I filled up and started the car again performed fine after that however the check engine light was solid now and still on. I went to my local mechanic and he read that code P0300. I changed my spark plugs that day and they were crap the original spark plugs I have 65,xxx on my car now. Car is smooth now. I cleared check engine when i saw him first and it did not come back on all day even before i changed the spark plugs later that night. Why my light was flashing and why my car was acting like that till i filled up?
View 6 Replies
2004 Elantra AT ... 6 months ago top of the radiator cracked caused it to overheat and blow the head gasket and warp the head. Repaired that and compression is fine now. It ran great for 4 months but now it randomly stalls. at or near idle. Seems to do it more at operating temp rather then cold. Occasionally the check engine light will pop on and the code reads (random misfire). It acts just like it has been shut off. But immediately restarts.
View 3 Replies
The check engine light is on in my 1996 Honda Civic. The code for it is P1382, which is supposed to be either a misfire or the ignition control system. It runs fine most of the time, but intermittently cuts out while I am driving sometimes. I have replaced the spark plugs and fuel filter and the check engine light actually went off after replacing the fuel filter, but came back on the second time I drove the car. The distributer was replaced not quite a year ago with a reman distributor.
View 2 Replies
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong. Any way to check what's wrong myself?
Also just to double check, the cylinder number is 1, 3, 5, 7 for the passenger side front to back right? And 2, 4, 6, 8 for drivers side? And front to back means when looking at the front of the car? 2001 7.3 Excursion Limited with 232k miles...
View 6 Replies
I just picked up a 2011 Ford F350 about 8 months ago. I have had troubles with the check engine light coming and going. Now it's been on for good with loss of power. I have had the codes read and they came up as the p0401 and a code about the def heater. I can not remember that code off the top of my head. After some searching I have found a video about the def heater but nothing about the Egr cooler/valve. Is there anything out there about how to clean and remove the the cooler as I will be needing to do repairs myself as the truck has no warranty.
View 10 Replies
The check engine light has been coming on and off over the last month...SO, I replaced the MAF which I thought was the code 17550. After a couple hundred miles the check engine light came on again. SAME code, 17550 again...my tech is baffled.
View 10 Replies
On my wife's '99 Explorer, she just acquired, we had a P0303, #3 cylinder misfire. I found the plug cracked and replaced it. Do the codes reset themselves or do I have to do it? I'd rather not disconnect the battery and reprogram the radio.
View 7 Replies
