I was told by the dealership that the battery was bad and needed to be replaced ( which I did) I went out to my car this morning and had the same problem. When I turn the key nothing happens. When I turn the key you hear a click but that is it.
View 3 Replies2001 F150 4.6 V8 Triton
Automatic
Battery Tests Good
Starter Tests Good - I saw it spin and come out at the testing station at Autozone
Ignition Relay (the one in the fusebox)- New (8mo.)
Switch on the firewall on passenger side of truck - New (8mo.)
Battery terminals/connectors - Tight, no movement, Cleaned within the last week.
Starter connections - cleaned within the last week.
I am having trouble with my truck not starting. The issue has been occurring on and off for over a year. Usually, it happens about once a month, regardless of weather.
I turn the key, and there is one click. Usually at this point, I can use one hand to gently pull the shifter "up" towards park and turn the key again and it will start. Recently it is not starting when I do this. I have tried many times, and have tried to start it in Neutral (is that even possible with an Automatic?).
With the key in the "ON" position, I go under the truck and jump the starter cellinoid. I am jumping the small post to the big post where th wire comes from the battery. I do not touch the post that the wire goes into the starter.
I am very confused because it starts just fine without fail and almost instantly when I jump the posts. It is drive-able this way, but I would like to resolve this issue, and resume using my key to start it since the issue doesn't seem to be resolving itself as it usually does.
A friend told me about the Ignition Starter Switch inside the Column. If I have time I will attempt to start the truck with a screw driver on the switch tonight to narrow down the issue.
Have a 97 Ford explorer. Over 270,000 miles on it. Recently had Crank sensor, Crank case vent tube, plugs wires replaced along with intake manifold gaskets. Also had fuel injectors cleaned out. Now i cant get it to turn over. Went to store, truck started fine, came out and click. Thought it might be the battery even though its also brand new but no, had the starter checked, it is also good. Put test light on all electrical having to do with starter and found all hot wires and good grounds. Finally bypassed the solenoid for starter and still nothing but a click. I also checked NSS to see if that might be it but after putting it in reverse, the reverse lights came on, and even jiggled shifter in park and neutral to see if that might work but still just a click. Not sure where to go from here short of buying all new parts but doesn't make much sense to do that if they all appear to be working properly. Don't have a volt meter to check voltage.
View 5 RepliesI have a 1999 F150 Lariat 5.4 that's been sitting for a few weeks waiting for a new MAF. Finally got a MAF from a junkyard (out of an 01 Expedition) and installed it.
Turned the key, cranks once, then I hear a loud click and then just continuous clicking. I did some research and people are saying this is just the starter solenoid and that the battery may be dead. I charged the battery a couple hours and waited until it showed 11.some volts, tried to start it again, didn't even turn over, just clicking. I also noticed the theft light blinking rapidly, but if it were the PATS acting up, wouldn't the motor at least turnover?
So I went back to charging the battery. Went out a couple hours later (at night), and when I opened the door, none of the lights came on. Then I hear a click, the lights come on, followed by another click, and the lights went off. This happens each time I open and close the door. So did I potentially pop a fuse? Or is my battery just fried? Would replacing the MAF with the newer one out of the expedition cause any weird issue? I doubt it, but anything is possible at this point I guess.
1998 Ranger, 3.0 liter manual transmission. The vehicle recently has had the engine replaced. Still a 3.0 Liter, but possibly is from a 1995 or 1996 Ranger. Replacement motor from a wrecking yard, appears to have been sitting for quite some time prior to purchasing. I had a friend change the motor out after getting the vehicle a few weeks ago.
Ranger drove fine for a week, but this morning it wouldn't start. One click is all it would give when you turned the key. Thinking the culprit was the all in one starter/solenoid, I replaced it with a new one this morning. Now the solenoid will click continuously when the key is turned, starter still will not rotate then engine.
Battery tests good - 12.4 volts; connections appeared fairly corroded.
Here is what I have done:
- Clipped off the first half inch of corroded terminal leads, replaced both sides with new battery connectors and wire brushed connections off at battery and starter.
- Replaced Starter
- With "S" connector disconnected, attempted to bypass starter connections and short terminals to see if a faulty clutch position sensor was to blame; shorting did not produce anything other than turning the key did.
- Paralleled an additional cable from battery to starter terminal to see if corroded wire connections were to blame; still just clicked repeatedly when attempting to start.
Crankshaft does rotate manually, does not appear to be seized up. Unsure of what else to check for. Not confident in friend's engine installation abilities, he may have screwed up something I'm not thinking of. On the other hand, I don't believe I would have been capable of swapping out the motor myself.
My son has a 2001 explorer sport that he keeps at college. The vehicle sits alot more than it runs these days. Recently it some times does not want to start, no click when you turn the key. He got it home today, and after I changed oil, it would not start. I have no ground to the starter relay in the power distribution box.
I have no electrical schematics, where the ground for the starter relay comes from ? If I remove the relay and run jumper wires from the box to the relay, i can make the vehicle crank when i apply another ground source to the relay....but it just cranks, will not start.
i have a 96 slt v8 dakota im trying to fix myself. it wont start. put new batt. new starter motor. it just clicks engine wont turn everything in truck is working but when i turn the key to start its just clicks and my radio losses power. so i took out radio and still wont start...
View 2 RepliesHas happened twice now but last night I had to disconnect the battery. A few years ago the driver's door switch was replaced for the same reason. I would do it again but I can't find anything that looks like a switch. Where that thing is? It is a '98 Explorer XLT.
View 4 Replies1998 explore will not start when hot will turn over sputter and die, after 15 minutes it will start right up that was last monday when it was 80 outside it now colder outside has not done it again, the only thing i have seen that temp gauge is not going past cold never getting to center it will try and drop back down...
View 11 RepliesWhy doesn't my 98 Ford Crown Vic Police package turn over when it is hot outside and the car is hot? Winter time, I never have the issue. When the outside temp hits the upper 70s or more, and I drive for a little bit, turn the car off it will not start or even turn over. The lights come on like normal. I wait 15-30 minutes, it fires right up. I have replaced the starter/solenoid, battery, battery terminals, ignition relay.
98 crown vic police-4.6 liter Coil-on-plug,electronic timing,182,000 miles
I have a 1998 Explorer XLT V6 (4.0 SOHC) with an AC problem. The AC compressor will not turn on via normal means - turn to AC or AC Max, rotate temp to left. It hasn't been a problem as I never use the AC, but I'm fixing a few of the minor inconveniences (dash lamps, re-solder radio) and figured, why not look at the AC too.
A while back my mechanic said he used the Explorer to test his AC equipment and made sure the Freon was good. He said everything was working. I am assuming he was able to control the AC system from his tools under the hood. This tells me the system is good and the problem is related to the temperature control or a switch somewhere.
A friend of mine have a 94' Explorer with the 4.0 v6. Fuel pump starts for 2-3 sec when i turn the key, stops when cranking and starts again when i stop cranking. i checked the fuel shutoff switch and it was ok, and it have spark.
View 3 RepliesWe bought it and the dude that owned it cut the radio wires and messed with the wiring everywhere because he thought he had a short. I've hooked up the radio and everything and it does the same thing. How do I bypass to make it stay running.
View 10 RepliesThe right turn signal on my 1998 Ford Explorer recently stopped working. The flasher was making a horrible buzzing sound when I tried to signal right, but worked fine signaling left.
I just replaced the flasher, which has cleared up the buzzing noise when trying to signal right. The flasher clicks like it's supposed to, but the lights still do not flash.
Here's a summary of the current symptoms:
-Hazard lights work fineFlasher clicks; interior indicators flash; exterior lights flash
-Left right signal indicator works fineFlasher clicks; interior indicators flash; exterior lights flash
-Right turn signal does not work
-Flasher clicks
-Interior indicator stash off; exterior lights stay off
What to check next???
My 1998 Honda accord coupe 3.0 has 225 k miles has a new sending unit, fuel pump, main relay, ignition switch, and spark plugs. I cannot find the source of why my car will not start I replaced these things on my car due to car didn't want start. Then it was fine every time I would turn a corner or drive it rpms would drop like I was running out of gas then it would die now it will not start.
I have checked all fuses. I have read in forums that this could take a lot of money to fix only because no one knows the source of why its not starting. I am a disabled female that is just trying too have a running vehicle and can't figure out why it won't start. It has a new battery but won't hold a charge. Had charged it from my friends car for 25 minutes it gave it enough juice to put it in neutral and push it in the driveway with another car.
My 98 Cirrus (V6 automatic) is not starting. The battery is working fine and it lights up everything...the wipers, headlight, the turn signals etc.... But when I turn on the ignition...nothing. I hear a mild thud followed by a brief hissing sound when I turn the key from the 1 position to the 2 position (referring to a 0-1-2-ignition key positions)...like "thuh...sssssss." It seems it comes from the underside of the car. Then when I turn from the second key position to start the engine, I get no response at all. I tried putting the gear in park / N...but no difference.
The weird thing is, approx 15 min before I attempted to start the car, I had to drive the car across the parking lot. It ran fine at that time. Could it be a fried starter motor?
Drove it last night around 9pm. Parked it and went to drive it again this morning around 7:30. No cold weather here or rain. Here is what I know: When I turn the key I hear a click (not a repeating click) but the engine doesn't turn over. Batteries have 12.5 volts. I put my trickle charger on them and had full charge after about 3 or 4 minutes. When I turn the key the headlights do not go dim. I put a screw driver across the solenoid on the passenger side fender and got a strong arc. When I do that, I can also hear another click that sounds like its coming from the engine. I tapped the starter a few times with a hammer, but it still wont turn over. I'm guessing bad starter.
View 14 Replies2002 explorer 4.0l. No crank just click new starter in and cables hooked to battery...
View 1 RepliesI work for the transportation department at a school and we have a bunch of 6.0 f350/450 busses and this bus I am working on has a no crank condition. Bus in question is a 2006 F450 6.0.
Currently if you turn the key to start the engine the solenoid just clicks but the engine wont crank. The person working on it before me assumed that the batteries and or starter were bad so they were replaced(0 miles on them right now) but the problem still persists.
First thing I did when I started working on this bus was jumping the starter relay and the starter engages and starts the engine perfectly. That being said I know the starter wiring is fine.
Secondly I looked through the wiring diagrams and saw that the PCM grounds the 85 terminal on the starter relay so I tried grounding the 85 and I was able to crank the engine with the key so that was telling me that the actual starter relay is fine. Next I went and swapped the PCM with another 2006 f450 thinking maybe the grounding switch in the PCM was bad and I have the same no crank condition. The PCM from the bus in question was swapped to the doner bus and it cranked perfectly(PCM in question is fine).
Next thing I did was look up all of the ground locations for the PCM or anything to do with the starter and they were all cleaned and still have the same no crank.
Looking around on the internet I see that the viscous fan can cause a problem if it shorts out so I unplugged that and no change in the no crank. I also saw that the trans range sensor could cause a no crank condition but I am getting back up lights/beeper and the bus "wants" to crank so I am thinking that the TRS is not the problem.
Lastly I tried hooking my Modis scanner up to this bus and was NOT able to communicate with either of the PCM's I tried. Not sure if this is related to my no crank condition. I checked all of the wiring that I could but could not find any chafing or breaks in any of the OBDII wiring. My planned next step is to replace the TRS...
I have a 1996 4.0L Sport - 2 weeks ago, stranded wifey at food store, had it towed home, and replaced the starter solenoid - it started and ran for about 4 days, and then stalled once but started back up (it was cold out)
Another day, I went out to start it, and the same thing... loud click when you turn the key to start position, seems to be coming from solenoid again...
so, I thought, ok, the parts a week old, but sometimes they do fail...
So, I bought the best one around: standard "blue" which had brass on the back to best couple to ground, etc...
Put it in, and reconnected everything - and the SAME THING... clicks every time I turn the key. (single click for each time I try to start it....
questions is - how can I check these to see if I had 2 bad ones in a row, or would there be something else wrong?
I have a 1999 Explorer with a 4.0 engine and when it gets cold it has trouble starting. It will click for a while and then start, but when it is warm I have no problem starting it.
View 3 Replies