Ford - Explorer :: 1998 - Clicking Noise Coming From Front Driveshaft?
Jun 20, 2011
I have 98 ford explorer sport 4x4 does has a clicking noise coming from the front driveshaft that connects the transfer case to the front differential. At first we thought it was the front drivers side cv joint which we replaced. nothing changed. there is still a noise apparently coming from the front driveshaft. we can not tell if it is the front differential or the transfer case itself. The noise is being transfer through the front driveshaft. It sounds a bearing is going bad.
View 1 Replies
Advertisement
I suspect my rear driveshaft is causing the vibration/noise I thought was coming from the front. I posted a few days ago about how I suspected it was my front wheel bearings making noise. Now its vibrating real bad and feels like a universal joint.
Can I pull the rear driveshaft out and drive off the front wheels with the switch in the 4x4 position? Last year my wife drove for a few days with no front driveshaft as I had one on order. It worked fine, for that.
I just want to go for a test drive to make sure that its the rear shaft, and not something else.
View 11 Replies
I have a 2004 explorer that has a clicking/rattling noise in the front of the engine. What i found is that the bottom pulley has a sleeve or ring inside of that pulley that is just floating loosely back and forth. What this is or what it is supposed to be ??? If it is a bad part, what is the best way to fix it ?
View 12 Replies
My 1997 4.0 Rear Wheel Drive is making a clicking noise when it is put into gear or when it switches from drive to reverse and vice versa. Sound is coming from the back of van. Does not make noise all the time. Drove 50 miles last night with no problems and minimal clicking. Could it be U-Joints going bad? Or is this a different problem?
View 6 Replies
My 1998 Explorer is making a terrible banging noise when driving. It appears to come from the rear. It only occurs when i step on the gas, gives a bang and the car shudders lightly. The bang can be gone for 10 - 30 seconds, and all of a sudden appear again. If I step hard on the gas, it will make a bang! bang! bang! noise.. If let my foot off the gas, it rolls quitely without any noise.
I have greased the slip yoke, inspected the U-joints, checked the rear calipers, opened the rear axle/differential plate - no metal parts or excessive wear were observed.. The transmission runs smoothly, there are no other noises apart from the bang. It is as if someone is hitting the car with a hammer from underneath...
View 14 Replies
There's a high pitched whine type noise coming from my Mass Airflow Sensor. I can get it to go away temporarily if I goose the gas pedal, but it comes back after a minute or two. Has not affected drive-ability, but it's pretty annoying. It sounds like the hot wire is probably vibrating. Is there any fix for it, or do I have to replace the sensor to get rid of it?? Have tried cleaning it, but that did not work.
View 6 Replies
On my way to see my folks and I started feeling a vibration like driveshaft or wheel bearing between 45-55 mph then at about 75 then BOOM! Pulled over and found a pool of ATF thought my stock 4R100 just bit the dust but looking at it the fluid is coming from the front driveshaft at the Tcase. My hubs are unlocked and my ESOF is in 2HI but I assume my tcase was locked. Also since the tcase is probably screwed I'm goin to do the 271 with manual hub swap, how hard that is?
View 10 Replies
I have a 1998 F150 with a 4.6 engine and is a 4x4 now the other day when I was backing out of the garage I heard a clunk noise and it seems like it is coming from the right front, so I tried it going forward it made the same noise but not as bad. There is no road noise and all the u joints are good and tight, the noise was when I gave it a little gas. My question is the front cv u joint would this make the noise? And what about the hub? What is the proper why to check the CV joint and the hub? The noise was when I was in 2 wheel drive.
View 14 Replies
My daughter recently got a '92 f-150 SCAB 4x4, 302 w/ E4OD. The trans needed new seals in the front pump, so I did those and replaced the filter and fluid while at it. Now it runs fine, but it makes a nasty ticking or clicking noise. It is definitely coming from the front of the trans. I was thinking it was a cracked flexplate, so I pulled the inspection cover yesterday, but could not see any cracks. I have heard that sometimes you cannot see the cracks, as they are tiny, or around the crank bolts, which are not visible from the inspection cover. Is this the case? Also, could the torque converter be the culprit? I haven't heard of this kind of noise coming from the TC, but then, I've dealt mainly with manuals.
View 7 Replies
2002 ford explorer v8 4x4, ok I had some noise coming front the right maybe middle axle area so I pulled the driver's side tire and inspected all the bushings ball joints and hubs. The hub had a little play and so did the upper ball joint. So I replaced the hub thinking this could be the problem and the steering stabilizer bar (all the bushing on the bar where toast). Ever thing was tight but the upper ball joint still had a little play but not enough for me to spend the $ to replace the whole control are (as I am told you cannot replace just the ball joints you have to replace the whole control arm). Any way got it all back together and still same nose. What it could be? Also the four wheel low will not engage could this be part of the problem or one more thing un related ( the four high engages just not the low)...
View 14 Replies
For starters I have a 1999 F-250 5.4l changed all 4 ball joints about 15,000 miles ago. I have been hearing a grinding noise coming from the front end for the last month only when I turn left and at slow speeds. I was servicing the TC so I threw it in 4 wheel to check it and it wouldn't engage until I started moving. When it did engage it was a bad grinding/ clunking sound coming from maybe the differential.
View 14 Replies
I have had a Clicking noise on my 2000 x 4x4 since 6 months coming from the front right side tire noticeable over rough roads or over bumps and I went on a journey starting with ford dealer to almost all well recognized service centers and every body says your front suspension is ok and no one seems to know where it is coming from. I thought it was my hub bearing since it fails almost every year but when I was changing the bearing, I noticed a big Excessive play in axle.
See video : My AXLE Shaft - YouTube
Also I noticed oil mixed with grease the grease is prawny with a reddish sort of color or that is some thing else.
See photos ....
Any way after replacing the hub Bearing with a used one and butting every thing together I went on a test drive. Noticed that the vehicle drive line is not right the car seems to wonder and the noise still there so i didn't get far i came right back and park my x then a funny burned oil smell was present.
Is it some thing i did wrong or is it bad situation gone worst ?
Items Checked Or Replaced In The Last 4 Months ( trying to fix)
Tie Rods. Ok
ball joints. Ok
suspension front and rear. Ok
Front stabilizer bar. Ok
control arm bushings. Ok
stabilizer bar bushings Ok
steering linkage. Ok
brake pads. A new front set installed
Rotors . Both front changed with oem parts
body mounts + sub-frame mounts. Some replaced
shock absorbers . New 4 set installed
- Rear Monroe 911176 Reflex Light Truck Shock Absorber
- Front Monroe 911175 Reflex Light Truck Shock Absorber
tires. Replaced with a new set off four
Hub Bearing. Second hand (that's when I saw it)
Spare Parts waiting list (Ordered):-
O ring ord part # 4C3Z-1K106-AA
(knuckle seal) (F81Z-3254-CB).
and some other dust seals which i can't recall.
I am looking for how to fix axle play and get red of the noise. (this is a video from you tube for clearance)....
F250 wheel bearing, is this bad or not? - YouTube
View 8 Replies
A while back I posted a thread trying to fix a clicking noise coming from the front end on my F-350 dually when applying the brakes at slow speeds (under 15 mph).
While returning from our camping trip last week the noise is back again. It does not occur after the truck sits overnight or for a few hours. But after driving for 30 minutes or longer the clicking will return when I apply the brakes at slow speeds. I tested the rotor temps with a heat gun and it seems to start when the rotor temps get above 120 degrees F. So I removed the brake pads & calipers, regreased the slide pins, cleaned up the pads and applied some lubricant on the back of the pads. I also bent the pad clips so they would fit snugger/tighter in the slots.
Whatever I did seemed to cure the clicking while driving around this weekend. I made sure I got the front brakes nice and warm - up to 180 degrees or so.
When I did this same procedure a few months ago the clicking went away - but eventually returned.
Should I get some better clips? Replace the sliding pins? Pads? The rotors & pads were replaced this winter & the shop said they and the labor are still under warranty. But if they use the same clips - I'm concerned I'll be back to square one in a month or so.
View 14 Replies
I thought there was a v10 specific superduty section like how the psd does, but my thread went in the "performance, engine, troubleshooting" section.
I wanted more exposure than that particular small viewed area.
I don't have a video of the noise, but my 99 f450 v10 5spd has some iffy noise coming from the front. I've read so many threads on this and they either end with "my motor had 1-2-3 bad pistons" or "my flexplate was cracked" and all that dealt with chain tensioners were never finished.
I know what piston slap sounds like (worked on many cobras and lightnings with forged pistons that had it) and have experience with bad wrist pins and broken piston skirts, and this noise doesn't sound like any of it.
Noise is a loud clicking/clunking/Detroit diesel idle noise. When you rev the engine up it doesn't lighten or get better, only worse as rpm goes up. Oil is terrible looking, I'll be getting that changed this week.
Story on truck. I've had this thing for 4 years with blown motor. I got a buddy that acquired a parts truck and he said it ran good. I dropped my truck off and he swapped the engine. I got my truck back running, but with this engine noise. He said it needs to get run some more and change oil.
I think it's timing tensioners, my buddy says it will come out of it, a mechanic friend says it's going to blow up "because they all do" and I don't really want to replace the engine again.
If it's tensioners, how big of a job is it. I have the cam clamps and crank stop and the ford tools to make sure crank and cams don't rotate while apart.
I'm just 650 miles from my truck and may need someone else to do the work. Which sucks.
View 4 Replies
I have a 2005 Trailblazer EXT 4wd. I have an issue with my front driveshaft. I have been hearing a squeaking in a tin can kind of sound. It is kind of hard to describe. I thought front brakes. Checked them and they are fine. I crawled up under the front end and took off the skid shield to look around. Since it was in 2wd I tried to turn the front driveshaft by hand and there was the sound. The driveshaft does turn and the sound was appearing to come from the front diff.
I thought "Oh Crap" is there fluid in the front diff. It would make sense if it was empty to make a sound like this. I unscrewed the filler hole and there was fluid. Then I decided to flush and fill the front diff with fresh fluid. It was pretty dark and I don't know when the last time the front diff was serviced. I took it out for test drive and still have the noise. What i am asking now is what to look for next? Like I said, when turning the front driveshaft by hand in 2wd it makes that sound.
By the way, 4wd works just fine in all modes.
View 6 Replies
Got a 2007 Santa Fe CM (Europe) with 160k km. I'm currently trying to figure out how to fix the clunk noise in the front of the vehicle. I am aware about the TSB 12-DS-002 where they recommend changing the drive shaft washer, but since that's a lot of work I want to make sure that this is really the problem.
The noise is not always there. Sometimes you can hear the clunk when decelerating, but not always. You can also sometimes hear a clunk when going from D to R. It sounds like a driveshaft has some play, and a change in the direction of the force causes it to slam into the other side. However, you can't feel it, so there is definitely not a lot of force behind it. You can only hear it.
However, I asked some guys to shift between R and D while I'm outside so that I can figure out where the sound comes from. However, murphy's law, it didn't made any clunk. And after shifting between R and D for like 20 times I felt bad for my transmission and stopped it.
The clunk is not always there, just sometimes. It doesn't really make sense to me, if its really play in a driveshaft it should be always there? Also the clunk started at about 155k km, now I got 160k.
Is there any further diagnostics I could do?
View 5 Replies
I took my car to the dealer last week to repair a clicking noise coming from the juncture of the right front windshield and dash. They said they added felt to the speaker grill and fixed it. NOT SO, still makes the noise, it is better though seems to get better when the weather is warmer. How to get the speaker grill off without damaging it. If so I will try to address the thing myself.
View 14 Replies
I've only started noticing this recently. I have a 2004 W12 with roughly 75k miles. It seems to only happen after the engine warms up, but even then its seemingly randomly. I'll notice a clicking sound coming from the front passenger side of the engine. The sound increases in frequency as I rev the engine. I have no check engine lights and no noticeable loss of power. Its not a radiator fan since the sound is still audible when the hood is open. I'm getting no CAN errors with my generic OBDII scanner (I know its not a VAG-COM but hey).
I've been reading up on the possibility of it being a bad valve lifter. I don't know much about them and was hoping to get some advice here before I go about asking my dealership to diagnose the sound. I found this random article through google vaguely talking about replacing the lifter. The person says its "reasonable and inexpensive".
I also stumbled across this thread here describing what sounds similar. Although the thread provides no closure it seems towards the end people are hinting that the engine needs to be pulled? This is contradictory to the first source I found. My question is, say it was a bad lifter, whats the extent of work required to fix it? The Parts seem to be really cheap if I'm looking at the correct stuff?
View 2 Replies
I have an 97 Altima. When I hit on the brakes, it seems to be okay, but once I let the pedal go, there are clicking noise coming for the front wheels.
View 9 Replies
Took my car in for 10k mile service and let them know there has been some clicking noise coming from the front suspension when making a left/right turn...
I dropped off my car on September 21st and they have yet to complete my car... I've called them every single day since but, I don't get a good explanation from the dealer...
View 10 Replies
Noticed a clicking noise when only turning left out of a parking lot today? What this could be? Sounds like it was coming from the driver side front wheel?
View 2 Replies
