Ford - Explorer :: 1997 Won't Even Turn Over / Just Getting Click From Starter
Jul 3, 2014
Have a 97 Ford explorer. Over 270,000 miles on it. Recently had Crank sensor, Crank case vent tube, plugs wires replaced along with intake manifold gaskets. Also had fuel injectors cleaned out. Now i cant get it to turn over. Went to store, truck started fine, came out and click. Thought it might be the battery even though its also brand new but no, had the starter checked, it is also good. Put test light on all electrical having to do with starter and found all hot wires and good grounds. Finally bypassed the solenoid for starter and still nothing but a click. I also checked NSS to see if that might be it but after putting it in reverse, the reverse lights came on, and even jiggled shifter in park and neutral to see if that might work but still just a click. Not sure where to go from here short of buying all new parts but doesn't make much sense to do that if they all appear to be working properly. Don't have a volt meter to check voltage.
View 5 Replies
Advertisement
I'm having some strange electrical issues b where to start fixing the problems. Here is whats happening:
- Put the key into the ignition and turn to the "on" position, full power to everything no issues at this point
- Turn the key to the start position, get 1 click out of the starter and then lose all power to everything
- Turn the key off and back to "on" position, sometimes I get power at this point and sometimes the power stays dead for a while
- Check the battery, which is good (12.3 volts)
- At one point someone noticed some sparks coming from a connector near the back of the firewall on the passenger side (sits on top of a metal cover with a large positive terminal right behind it). I've disconnected this terminal, cleaned it and put on some dielectric grease all of which hasn't done anything.
- Basically I mess around with few things, check some connectors, let it sit for a few minutes and then it will start.
View 5 Replies
I got a 1997 f150 4x4 4.6L had to replace fuel rail after a couple holes were rubbed in it and caused a fire, but now after two weeks of it sitting at the dealer, I wasn't gonna pay for a fuel rail to be put on so i had it towed home and I did it, however now when I go to start it, it just clicks. So I have the battery tested and its bad so it was still warrantied so it now has a new battery and i also replaced the starter solenoid while i was at it. But still just a click when i try to start it. I had the starter out and bench tested it and it went but went slow and looked very old and tired, I am thinking i need a starter now because its a click from the starter, like its trying to go but isn't strong enough.
View 3 Replies
2001 6.8 Ex wouldn't start again today Get a loud click but starter doesn't turn over. Yesterday jumped it, took it to Advance where they checked battery and alternator; both checked out great. To start it this morning I ran my negative jumper from battery to engine block and it fired up It's about 12 degrees out and was same yesterday. Thinking dirty/bad ground somewhere ? Do I just start following the negative cable everywhere it goes or am I missing something here No garage and it is chilly.
View 3 Replies
I have an 02 F250 6.8 with 51,000 miles on it. I recently replaced the battery about a week ago, and only actually drove it yesterday for the first time since replacing the battery. I drove it about 25 miles, parked, and when I went to restart, it wouldn't. The starter doesn't crank, so I mean its not a cranking issue as in cranking, and not starting. It only clicks at the relay when turning the key. It acts like when you try to use a wrong chip coded key.
All of the dash lights came on, and I can hear the relay clicking, but that's it. I swapped the relays around, and no luck. If I let it sit a while, about an hour, it will fire right up. The battery cables are tight and free of corrosion. I am curious, since I just put in a new battery, could this be the culprit? Why will it start fine cold, but not hot? I have NEVER had an issue with this truck until now.
View 14 Replies
My mom has a 2001 f150 with a 5.0. Had never had any problems with it till this week. She says it wont click or anything. When she tries to start it, the power door locks go to locking & unlocking. She said the battery is good. I figured probably the starter. She lives about 2 1/2 hours from me. I figured I would go down there and take the starter off and have it checked or rebuilt. Anybody ever had their power locks to go to moving when you try to start the truck. Also, when she turns the key on, her dash lights come on just like normal. Just won't turn over or click or anything.
View 3 Replies
I have a 2006 Santa Fe with 137K miles on it. Has been best car I ever owned, but have recently experienced a strange issue where it won't start, meaning I put the key in the ignition, turn it to the right and nothing, not even a click on the starter. I have found if I move the shifter around from P to R to D, etc. and then try it again it will start. Is there a safety interlock switch in the shifter that could be going bad and is therefore not satisfied/happy when I try to start the car? Or could the ignition hardware where I insert the key be the issue.
View 1 Replies
I was told by the dealership that the battery was bad and needed to be replaced ( which I did) I went out to my car this morning and had the same problem. When I turn the key nothing happens. When I turn the key you hear a click but that is it.
View 3 Replies
I bought a used 2008 Toyota Camry per-certified from a local Toyota dealer about 2 years ago. About a year and a half ago I got in the car to go to work one morning and it would not start. You turn the key and all the lights come on but nothing else happened. Took the battery to Auto Zone and they said the battery was OK so I had it towed to the dealership. Dealer called when he got it and said it cranked right up for them and it has not been an issue since.
Two days ago I get in the car to leave work and the same thing happens. You might hear the starter click when you turn the key but nothing else happened. The car was getting power from the battery but that was about it. I tried to jump the car off but still the same thing. I had the car towed to a local Goodyear shop and after looking at it the said it was a problem with the alternator, that needed to be replaced, which also killed a cell in the battery that needed to be replaced also. They said since they are replacing the alternator they might as well replace the belt also.
View 14 Replies
I have a 2010 Accent with 106 000 km on it (Canada). A couple months ago (just as warranty expired) the car would not start. Nothing. Engine would not even turn over. Just a click of the starter solenoid. battery had a load test and is fine. Removed negative battery cable and cleaned the cable where it bolts to the body under the battery tray. Battery terminals were both cleaned at the same time.
Things worked fine for a couple weeks and the problem is back but worse. Everything in the car works fine when it won't start. If I continually turn the key to the start position it will eventually start to turn over and start fine. Sometimes it takes 20-30 turns of the key till it turns over and starts. When it does turn over and start, the engine turns over fine at the normal speed. Not slow like a weak battery.
Dealer is useless. Had a coil go a couple months back just before the warranty expired and they told us that the reason the coil went was that the car had been rust proofed by someone other than Hyundai.
View 12 Replies
My son has a 2001 explorer sport that he keeps at college. The vehicle sits alot more than it runs these days. Recently it some times does not want to start, no click when you turn the key. He got it home today, and after I changed oil, it would not start. I have no ground to the starter relay in the power distribution box.
I have no electrical schematics, where the ground for the starter relay comes from ? If I remove the relay and run jumper wires from the box to the relay, i can make the vehicle crank when i apply another ground source to the relay....but it just cranks, will not start.
View 10 Replies
I have a '97 Explorer XLT with a 5.0L V8. Recently, I've developed a problem, in which it doesn't always start. Sometimes, when I turn the key, there is a very loud click (as if the solenoid is engaging), but there is no start. The battery is NEW, and confirmed good, and the terminal connections are tight. I have also replaced the solenoid, but the issue remains.
If I turn on the headlights, before trying to start it, the lights DO NOT dim when the key is turned...indicating NO draw, on the electrical system. I can try it several days a week, unsuccessfully. And then, one day, I can turn the key and it will start as if there was never a problem to begin with.
I have lost confidence in my favorite vehicle, as I am afraid to drive it if/when it does start, for fear of being stranded. I am thinking it may just have a bad armature, or windings in the starter, but if that doesn't correct it, I can't return the starter (as it is an electrical component).
View 9 Replies
2001 F150 4.6 V8 Triton
Automatic
Battery Tests Good
Starter Tests Good - I saw it spin and come out at the testing station at Autozone
Ignition Relay (the one in the fusebox)- New (8mo.)
Switch on the firewall on passenger side of truck - New (8mo.)
Battery terminals/connectors - Tight, no movement, Cleaned within the last week.
Starter connections - cleaned within the last week.
I am having trouble with my truck not starting. The issue has been occurring on and off for over a year. Usually, it happens about once a month, regardless of weather.
I turn the key, and there is one click. Usually at this point, I can use one hand to gently pull the shifter "up" towards park and turn the key again and it will start. Recently it is not starting when I do this. I have tried many times, and have tried to start it in Neutral (is that even possible with an Automatic?).
With the key in the "ON" position, I go under the truck and jump the starter cellinoid. I am jumping the small post to the big post where th wire comes from the battery. I do not touch the post that the wire goes into the starter.
I am very confused because it starts just fine without fail and almost instantly when I jump the posts. It is drive-able this way, but I would like to resolve this issue, and resume using my key to start it since the issue doesn't seem to be resolving itself as it usually does.
A friend told me about the Ignition Starter Switch inside the Column. If I have time I will attempt to start the truck with a screw driver on the switch tonight to narrow down the issue.
View 9 Replies
I have a 99 f150 2wd v6 4.2 liter engine. Im going to sum up what happened and what I've done so far. One morning truck wouldnt start. Wouldn't crank, turn over, or even make a click click noise. I tried jumping it just to be sure but it didnt do anything. Battery is fine, interior lamps, displays, and radio all work fine.
I took the starter off, had it tested, it was bad so i got a new one. Still had the same problem. Finally, i got underneath the trunk and bridged the positive and negative on the starter solenoid and it fired right up. So the starter is not the problem.
Next I looked into the starter relay, if I bridged the positive and negative on the starter relay it fires right up just like the starter. But since that is only bypassing the starter relay, it didnt tell me whether the starter relay was good or bad. So I got a new starter relay and it worked! It started with the key with no problem 3 times! I thought the problem was fixed but when i tried to start it an hour later, nothing... Same problem as before.
I checked all my fuses, none were blown.
I'm under the assumption that either something leading to the starter relay is making the starter relay go bad OR there isn't enough power going to the starter relay. Maybe something in the ignition, even though my accessories are all still working.
It is the only vehicle I have to and from work. For now I am getting by with bridging positive and negative on the starter relay to start it but that is only a temporary fix.
View 8 Replies
I have a 2002 F-150 xlt 4x4 5.4l V8, 96k miles. been sitting about 3 weeks i went to start it and nothing.. thought ok jump. We tried jumping/charging the battery nothing. then we switched batteries from running car same thing when i turn key just hear a click in dash. battery light remained on even when we swapped out. The theft light was off as well.
View 1 Replies
I have a 1999 F150 Lariat 5.4 that's been sitting for a few weeks waiting for a new MAF. Finally got a MAF from a junkyard (out of an 01 Expedition) and installed it.
Turned the key, cranks once, then I hear a loud click and then just continuous clicking. I did some research and people are saying this is just the starter solenoid and that the battery may be dead. I charged the battery a couple hours and waited until it showed 11.some volts, tried to start it again, didn't even turn over, just clicking. I also noticed the theft light blinking rapidly, but if it were the PATS acting up, wouldn't the motor at least turnover?
So I went back to charging the battery. Went out a couple hours later (at night), and when I opened the door, none of the lights came on. Then I hear a click, the lights come on, followed by another click, and the lights went off. This happens each time I open and close the door. So did I potentially pop a fuse? Or is my battery just fried? Would replacing the MAF with the newer one out of the expedition cause any weird issue? I doubt it, but anything is possible at this point I guess.
View 10 Replies
I have 98 f150 with 4.6 starter went so I put a new one on wich was a hassle and it tries to turn but just wont as if the motor is seized. I had been hear a loud howling sound from what I think is the ac unit and the ac line burst after trying to start. Would a bearing or something with the AC be enough to stop the engine from turning over? Or could it maybe be a wire connection problem? To me it sounds like a starter trying to start a seized motor but I cant see that my motor would be out it only has 190 000km and the oil looks good. but we couldn't turn the motor over with a ratchet? The truck had been getting gutless. I am stuck...
View 4 Replies
Ok so I was looking at my blend door actuator motor to see if it was working. Just took off the bottom vent cover, turned key on and moved the air mixture to see if the motor worked. (it didn't) Then I went to start the truck and all I get is the solenoid on the firewall click each time I turn the key. I put a meter on the opposite side of solenoid and I see 12v across the solenoid. I can't image i did anything while playing around by the blend door actuator motor. I guess I'm looking for confirmation that the next logical step is starter and starter solenoid. Is there anything else I could be missing? is there anything else in that circuit between the solenoid on the firewall and the starter? I also cleaned the battery terminals and the terminals down on the starter solenoid. I also tapped the starter a bunch and put a charger on battery and tried jumping the truck too. Everything else works.
View 10 Replies
I have an 02 f150 5.4 4x4, drowned it a while back, thought i had hydro lock, crank can be turned by hand though as far as i can with a wrench, so internals seem to be fine, no bent or broken rods that i could tell, ripped everything apart cleaned it up put it back together, new fuses, new ignition relay, new starter, alternator and battery as well, turned the key to on and got all my electronic stuff back up, turned to start and it all goes dark, which i assume is because at that point its sending power to the starter, but the starter didn't turn or crank the engine...
So question being when i put my new starter on is it possible that i might have crossed a wire or something that would cause it to not crank? and due to the fact that I had water in it, and had hydro locked it, all my plugs are out, now I know that spark is needed for the engine to run, but shouldn't be needed just for the crank to turn right? question being is that once i fix the wires on my starter, I am looking for initial crank before start up, so do i need to put a plug or two back in and hook them up to make it crank? or will it crank without them? and yes I did replace all my fluids as well.
View 8 Replies
After getting the oil changed in my 1997 Ford F-150 4.6L with 150K miles at a local quick lube, I made one stop and my truck wouldn't start. I could hear the starter engage the flywheel, but couldn't turn it over at all. Oil was clean and full. I bench tested the starter and it tests good. I put a breaker bar on the crankcase nut and I could barely move it. Oil level was about 2 quarts low before oil change.
View 10 Replies
I have a 2001 supercab 4x4 with a 4.6 in it, it has 186k on it and the only issues I've had was a misfire not to long ago. I replaced the plugs and coil packs and fixed that issue. 2 days ago she ran fine with no issues and this morning I went out to go to the store and she wouldn't start. All the dash lights come on and all of that normal stuff when you turn the key. When I turn the key I hear what sounds kind of like a clunking noise towards the bottom of the windshield and the middle of the dash. The starter does not engage, no nothing, really confused here. I thought maybe the battery was bad so I put my jumper on it and tried but again nothing happened.
View 14 Replies
