I'm working on a 1997 4.0 ohv and it has a hard start condition on first start up. any after that it will just be a crank no start condition unless you hold the gas pedal to the floor. Replaced the camshaft actuator, plenum gaskets, coolant temp sender and thermostat, fuel pressure is normal.
View 5 RepliesI have a 99 F150, Regular cab, long bed, with a weird brake problem. With the engine off, the pedal goes firm about 3 inches. But when you start it, the pedal goes to the floor.
I've replaced the master cylinder, and bled the heck out of the 4 wheel cylinders. No soap. The pedal goes nearly to the floor, and does not "pump up".....but does stop the truck.
The ABS light is "on".
I don't know what's going on maybe some body can shed a little light on this. If you hold the brake pedal down for a long period of time you can feel the pedal slowly go to the floor. So no problem I'll change the master cylinder bleed everything brand new fluid. Don't drive it much we let the sister in law drive it we'll I jump back into it the other day to go to Home Depot and once again I notice it still does it. Could the hydra brake booster be bleeding by or what's else could be causing this it's driving me insane. I really can't imagine the hydra booster causing a problem but it's new to me. I was thinking about bleeding the brakes again thinking there maybe there's air but I have run 2 bottles of brake fluid through how much more??
View 8 RepliesSo a few days ago the family and I were on a road trip. After driving for close to three hours we ran into a problem. We were doing about 75, which is about 3000 rpms with the 4.6L, When we dropped from 3k to about 400 and started to lose speed. I pushed the gas peddle all the way to the floor and no response at all. I pulled over and it had a very rough and choppy idle and it wanted to die. It eventually did. I checked all fuses with nothing found and i even hit the fuel pump shutoff reset. It started back up no problem and we got about 5 miles before it the exact same thing. Idle at about 400 rpms and no throttle response at all.
I shut it off and called a tow truck. It started up and they drove it onto the back of the tow truck and off at the local mechanic. They spent 2 whole days trying to diagnose it and even drove it for 4 hours straight, no issues. They pressure checked every system they could and tested every sensor they could. They could not find a single thing wrong with it. I drove it home 3 hours away with no issues. I got home and let it sit for about 10 minutes before I had to leave. I didn't make it more than 2 miles before the same issue popped up. I pulled over. Shut it off for 15 minutes and it started right up and drove home.
It threw 4 codes.
1. Pressure control solenoid malfunction
2. Fuel pump Primary circuit malfunction
3. Gear 3 ratio incorrect
4. Gear 4 Ratio incorrect
I've had 2 mechanics tell me its a PCM issue.
I bought a 97 f150 4x4 last week. I was cleaning the frame up with a wire brush on a grinder and accidently cut one of the front brake lines. Seeing how this truck has only 100k on it and all oem stuff on it, I decided to replace the front brake components, calipers, pads, rubber and steel lines. Got it all back together and bleed the air out of the front brakes. But the pedal still goes to the floor. I can pump them up with the key off but when i turn it on the pedal goes to the floor. I did not bleed the back brakes becasue I assumed that the master cylinder would be divided and independent of each other- back and front. So it this just that the back brakes needs bled or do I have another issue like bad booster- everything was working well before I cut the line?
View 6 RepliesI have a 2003 F-150 supercrew 4x4, was having problems with the brake pedal going to the floor, had replaced the front calipers, master cylinder and the brake booster. I have blead everything out including the rear calipers even though I didn`t touch them, the truck stops but the pedal isn't what it used to be, even when the truck is off the pedal has a tendency to go down, there is nothing leaking and not losing fluid, don`t know what else to do?
View 3 RepliesThe brake pedal intermittently goes to the floor on my nephew's 2003 F150 without grabbing at all. Pumping the brakes restores them, then they act normally for a while. I've replaced the master cylinder with a new Motorcraft unit, no change. No ABS codes. All rubber lines are in good shape. I'm stumped, although I suspect the ABS system somehow. I'm going to have him pull the ABS fuse and see if the problem goes away.
View 6 Replies2002 F-150 4x4 w/ 5.4 v-8. Brake pedal goes half way to floor before it starts to stop the vehicle. I have replaced and bled the master cylinder, bled out all of the calipers, and the calipers are installed correctly because the bleeder screws are at the top on all of them so no air can be trapped up there. The truck seems to stop fine, but just takes more pedal to get it to start stopping than I'm comfortable with. Could the ABS unit need bled out too? Or could it be an adjustment issue with the booster rod?
Also, something else I noticed, and it may be related..the ABS unit usually makes a slight clanking sound (like someone kicking a metal garbage can) a couple seconds after the key is turned on. I know its the ABS unit because a couple weeks ago I had a friends scanner hooked up to the truck, and I went into the ABS computer to clear the codes (have ABS light on from what I found to be a bad sensor wire on the front drivers side according to the scanner) and as soon as i cleared the codes on the ABS, it made that sound. I don't know if maybe there is something wrong with the ABS actuator, or if it's related to the brake pedal issue.
I have a 2000 SCrew KR F150. A couple of weeks ago I noticed the brake pedal was slowly going to the floor while at a red light. I pulled over and popped the hood checked the fluid reservoir. It was full, so obviously no wheel cylinder issues or fluid loss. I haven't had a chance to tear into it yet.
View 14 RepliesLast week my brake pedal started going to the floor when I stopped, it still stopped and felt fine on the top half of the pedal travel but then it would just slowly fade to the floor. I took it to a local shop and they said the master cylinder was leaking internally and my rear brakes were shot. I have 75,000 miles and the rear brakes were original so I told them to fix it. This is basically what I expected it to be.
They kept thinking they were getting defective master cylinders but after the two Napa parts and two Carquest parts they realized they misdiagnosed it and said I needed to take it to the dealership. I paid for the rear brake job since it needed done anyways and have an appointment for next week at the dealership. What might be causing the problem? I see no brake fluid leaks, no vacuum leaks, the booster was replaced 25,000 miles ago due to noise, no ABS light on, no CEL on, no other symptoms.
Installed a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
I've been working on this explorer for a week now and I figured it's time to ask around. My explorer won't start/crank, I've replaced the starter, battery terminals, tested voltages/amps/relays and fuses, still nothing. All i get is a heavy clunk, like the starter is engaging but the flexplate won't budge. It's a 2002 4.0 xlt automatic.
I'm fearing the engine is seized as I've tried manually turning the engine with a socket on the crank pulley bolt and even with a breaker bar I can't get it to move. The thing ran fine a week ago and I can't imagine this thing would seize at barely over 100k miles, not hydrolocked or anything I can think of, are these engines prone for spontaneous seizure or am I missing something?
We have a 94 ford explorer and every now and again it has issues on the start up. It will sound like it will want to crank over but just won't. If we wait 20 mins it will start up no problem. We have changed the fuel pump, fuel filter, ignition coil, and fuel pump relay but it still has this problem. Also occasionally the a/c blower wont turn on. Tonight it happened again and I pulled the fuel pump relay out and it was really hot, after it cooled down and was put back in the car started. I am beginning to think it maybe an overheating issue that is affecting the relays but am not sure. I was also wondering about changing out the relay box...
View 6 RepliesI have an Explorer Sport 2001 that will not crank nor start. I have replaced the following:
Crankshaft, camshaft sensors
Ignition coil
Ignition switch, neutral safety switch
Fuel filter
Fuel pump
Starter
The battery is less than 6 months old .. Still, the car will not crank, will not start. I have spark, voltage and fuel.
The PCM does NOT communicate with the scanner. I purchased a used PCM off of eBay. This one does communicate with a scanner and gives the following DTC codes:
P1120-- Throttle Position Sensor out of range
B1601-- Unprogrammed Pats Key
Since the car is in the Caribbean I can't tow it to a dealer.
When I go to start and depress the brake pedal it goes all the way to the floor. The brake fluid is at the full mark and my 2011 has only 25k miles. Where should I look since it did not go all the way to the floor when I forst got it with 6K miles.
View 19 RepliesSo my 2002 ford explorer with the 4.0 L V6, has been cranking along time before it starts. I thought i had this figured out already, i put a brand new fuel pump in it from the ford dealer. That seemed to work, but the problem came back.
Especially when it is cold, it cranks a lot longer than normal to start. and when it does start RMPS go way up briefly and come back down. Seems to only act up when its cold out, say 35 degrees and lower.
So the remote start wont work because it only cranks for a few seconds and then stops. it tries this three times and it gives up. i go out there to start it and cranks for 10 seconds it seems like, sometimes i have to feather the fuel pedal.
Picked up a super nice 03' as is with a no start. It cranks over nice and smooth, sounds like it has proper compression, and has proper fuel pressure. Tried spraying either in it and it will almost catch.
Tried putting a known good coil pack on it, no dice. Usually when other engine slip timing chains, it will crank rough, like a few cylinders are zero. This is not the case.
So I've been away a long time. My sister recently bought a 1997 Ford Explorer with the V8. When she tries to turn on the cruise she says it throws the transmission in to neutral and then locks the gas pedal...
View 5 RepliesI have an 04 Ford Explorer XLT 4.0 Flex Fuel. There has been loss of power to fuel pump. Relay and fuse both good, replaced the inertia switch...still nothing. Could a FPDM (fuel pump driver module) have anything to do with this issue? Or what should I check next? I am definitely at a loss as to what the issue could be! I know it is fuel related because I used starting fluid and it started right up and run for just a few seconds, so that should rule out ignition I think.
View 3 RepliesSometimes after running my 94 Limited, it doesn't want to start - it does crank - like it's not getting fuel. I have found the work around and want to know if it would be fixed by replacing the fuel pump relay.
The symptom is just after starting, it starts to run poorly, and then dies out, then will not start at all. I use to keep trying to start it for 20-40 minutes and suddenly it seemed to work.
It seems the work around is to turn the key to on for about 5 seconds and then turn it off - then it starts and runs as good as ever.
So, is this a symptom of a bad relay? I thought I'd start there because of the cost of the relay is fairly cheap. 1994 Explorer Limited 4x4?
I've got a 2002 Ford Sports Trac that won't start ! It will crank till battery dies but is not getting fuel. I have had it towed 4 times in the past year. of the 4 times,this last time it wont start. Every time that I have had it towed back to my house and dropped in the driveway it has started up with no problems. It will run for a few months or more.This last time it would not.
Could this be an electrical problem.Maybe loose ground somewhere or something else. Would like to rule out some things before investing in a fuel filter or fuel pump. Would hate to buy new FuelPump and that not be the problem. Can't find free wiring diaghrams for this issue.