Ford - Explorer :: 1997 - Clutch Won't Disengage
Dec 5, 2013
Ok so I have a 97 Ford Explorer 5-speed manual transmission. When I start the truck up in first gear, with my clutch pedal fully depressed, the truck goes forward as if im not pressing the clutch pedal down at all. And if I start the truck up in neutral, with the clutch pedal fully depressed, I cannot get into any gear. There are no leaks anywhere and there is plenty of fluid in the reservoir. What the problem may be or where i might wanna start looking?
View 1 Replies
Advertisement
I have a 1997b Chevy S10 ZR2. When I disengage the clutch the RPMs rev out of control, I shut the truck off and restart it, sometimes this works till the next shift. It used to be only when I would come to a complete stop now it is every time I shift... I have my 1 year old granddaughter and this is unsafe to drive with her and I am at a loss... replaced complete clutch assembly just a year ago and as it is when disengaged not clutch??
View 11 Replies
The cooling fan clutch never seems to disengage so I was wondering where can i find a clutch that is light duty so it will disengage easy and work with gas mileage napa list two different ones, maybe off a different vehicle....
View 3 Replies
2000 ranger, 4.0L 5spd 4x4
Recently my buddy's 2000 ranger's clutch stopped working, it wouldnt disengage. I checked the reservoir and it was empty, checked below and between the bellhousing and engine was soaked. I filled the reservoir up and attempted to bleed the system with my vacuum bleeder and it barely got any fluid out. Ordered a new slave cyl and just put it in today. You could see how wet the old one was when I took it out.
So today when I finished installing everything, I filled the reservoir and bled the system, lots of fluid coming through, everything seemed good, however the clutch still feels extremely light, and won't disengage. I looked at it through the inspection cover and there is maybe a 1/4" of movement total. I don't get why this thing is not working! How can you tell is the clutch master cylinder is bad?
View 3 Replies
This morning, I shifted into neutral and left the truck running. When I got in it put it in reverse, the shifter peddle went all the way to the floor and the clutch did not engage. I turned off the engine, and the transmission shifted easily. I put it into reverse, started the engine, and when I tried to shift back into first, the same thing happened. Pedal to the floor with no resistance, and I could not get it into gear. I finally forced it into 1st to get back into the driveway, but had to stall the engine to keep from going through the garage door. The clutch would not disengage at any time. I checked the master cylinder and it is 1/2 full. Has my clutch gone out?
View 14 Replies
So after putting my 2007 explorer in 4 high, it seems to be stuck that way. I can put into 4 low and hear it engage. When I select 4 high or 4 auto, I can hear the 4 low disengage. However, it never goes out of 4 high. The indicator goes off, but i can still feel it is engaged. What to do to turn it off?
View 1 Replies
The A/C in my truck stopped working last year, and this year I intend to fix it. I believe the problem is with the compressor clutch because it was making noise as it would engage or disengage. It was making this noise for a good year or so, and then one day the noise stopped and I have no A/C. So I am only assuming its the clutch.
View 4 Replies
I have a 1991 Ford F150 I bought. Told the transmission was shot, long story short, found out it was just a bad clutch. Pulled the transmission, replaced the clutch, pressure plate, and throw out bearing. Put everything back together, now i cant get the clutch to fully disengage. Had good pressure prior to replacement of the clutch, still has some pressure. just doesn't have enough to disengage the clutch. pulled the inspection cover, and verified the slave is moving. What is causing this issue?
View 14 Replies
I have verified that my AC clutch does disengage (and re-engage), but it seems like the AC is on all the time. Normally you don't notice this in the Northwest because I always overpower it with the heater, but now that it's above 70 on occasion, in vent and full cold, it still blows 20 degrees colder or more than outside air temp.
Is it possible that the clutch disengages but that the bearings are bad and its somehow still turning the compressor? Would a mechanic be able to diagnose this or would I just have to throw money at buying a new compressor? My first indication should have been that I get about 15-16mpg when I used to get 18+ occasionally.
View 14 Replies
I have a 2001 F550 flatbed tow truck with a 7.3 and the ZF 6 trans. i put a Luk clutch flywheel pressure plate new throw out bearing new clutch fork New clutch slave cylinder and master set up. When i push the clutch in it is VERY EASY compared to the way it was before. Ane when you push the clutch in and put it in gear you can hear the clutch disc rubbing on the flywheel and if you lift your foot the thickness of a hair the truck takes off. Also i can't engage my PTO because the clutch is not disengaging all the way. there is No adjustments on this set up. What Now.
View 2 Replies
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
View 3 Replies
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 Replies
I've got a 2000 F250, 5.4L 4x4 with the ZF5 5-speed transmission. Three years ago I replaced the complete clutch assembly, pressure plate, throw-out bearing, etc, and had the flywheel re-machined. Put it back in and all has been well. Only has about 15k miles on it. Earlier this week I went to drive it and all of the sudden it started getting harder to shift and by the end of the trip the clutch will not disengage at all when I push the pedal in.
Furthermore the pedal is much harder to push than it always has been. Checked the reservoir and it's fine. After some searching it seems to most likely be an issue with the master and/or slave cylinder either needing to be bled or replaced. Further reading revealed that bleeding and recommends just replacing the whole system, so I've priced that out. Was it a master/slave issue? Anything else I should check in case it isn't?
View 2 Replies
Ok santa fe 2006 (facelift) clutch was slipping. We've put new clutch kit in it (thrust bearing; friction and pressure plate). We discovered it had already had the DMF concersion to single mass. So we ordered the single mass clutch kit for it and fitted. All back together, clutch won't disengage and allow you to put it in gear!!! So took it all apart again to check the fitting as the inspection hatch it just didnt appear all fingers on the pressure plate was being pulled.. all looked correct, thrust bearing snapped in to place as it should... we got box back on (making sure the lever entered the thrust bearing correctly) and still no luck. When you press the clutch you can pull the rubber on the slave cylinder back and the piston moves all the way to the circlip. There appears to be movement on the pressure plate in the box. At a complete loss.......... what could have happened?
View 3 Replies
Santa Fe 2003 petrol manual 2.4
I had a slipping clutch so decided to change it myself.
I replaced the Dual Mass Flywheel the clutch pressure plate and clutch plate.
Re assembled and the car started first time but the clutch would not disengage.
Pressed the clutch peddle down and it went to the floor until the fluid had filled then it went solid.
I pressed it down again and the clutch did not release so pressed harder and 'pop' the master clynder went - but the clutch would not disengage.
Taken the gearbox back off now and the release bearing is in sit it just would not disengage -
View 4 Replies
We swapped transmissions in 01 elantras.. We installed a new clutch kit . When we go to start the clutch won't completely disengage, it only pulls it some, not enough. We replaced Tran fluid and bled it. We swapped out the throw out bearing arm and at first it worked now it doesn't..
View 3 Replies
I have a 95 Honda civic with a d15b block and a d16z6 head millage unknown I put a new clutch in it already had a new slave and master I installed a few weeks ago and when the car is running with out the clutch pressed in I can run through all the gears shift with ease it's like the clutch is pressed in but it's not
I've tried dropping the tranny and checking the pressure plate the clutch disc throw out bearing pilot bearing all good and installed right I rebleed the system then I removed the slave to see if it was in the hydroelectric system and still no change what am I missing.
View 19 Replies
Just noticed yesterday that the compressor clutch does not disengage while the air conditioner is on. It is 2005 V6 Sonata Elite. All the other cars I have ever owned had compressor clutches that cycle. Internet searches indicate that there might be air conditioners with only a low-pressure switch.
View 2 Replies
I picked up my Santa Fe yesterday. 7 seater Premium manual.
However the clutch does not seem to disengage until very close to the floor almost to the extent that I feel the gears crunch and r a little notchy in use because of this ???
Is this a characteristic of the manual gearbox for the new model ???
View 2 Replies
I just installed a new Sachs flywheel and clutch on my 1995 Chevy 1500 4x4. Got everything back together, filled up tranny fluid and gear oil, bled the clutch till no air came out and it still won't shift while the engine is running. I can get it into reverse with a little grinding when in 4H, but that's it. The stick moves freely when the engine is not running. Checked the master cylinder and it is moving just fine. I have checked and did not install the clutch plate facing the wrong way. Any other guesses on what I can do before I have to drop the transmission again and redo the whole install?
View 19 Replies
My clutch went out on my 98 Dodge Ram 2500 4WD the other day. I limped it home shifting like a big truck timing the shifts w/out the clutch. I replaced the slave cylinder w/ an aftermarket that had a bleeder. Bled it and got the pedal back up and it still wouldn't disengage the clutch. I replaced the master cylinder and started getting pedal back until I let the reservoir get too low and now after plenty of tries, I can't get any pressure built. I get a stream of fluid, but no air. Bench bleed the master and start over? I'm at a loss.
View 5 Replies
