Ford - Explorer :: 1997 - Can't Get Upper Rear Bolt Out?
Jun 8, 2017
I can't get the upper rear bolt out the fuel lines are in the way and I have tried wiggling the arm in every direction possible. any tricks?
97 V8 AWD.
Jun 8, 2017
Advertisement
Ford Super Duty (1999-2016) :: 2004 F250 - Driver Side Rear Sway Bar Link Upper Bolt Removal
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
Ford F-150 (2004-2008) :: Upper Strut Bolt Removal
I am in the process of installing a 6" pro comp lift on my 04 supercrew 4x4. Things were going good until I got to the upper strut bolts. Trying to remove the 3 nuts, one came off on the passenger side. The other 2 just spin, the bolt and nut. Haven't tried the drivers side yet. The only idea I had was making a notch in the top with a dremel tool and small cutting wheel for a screwdriver but my dremel tool smoked..
View 5 RepliesFord F-150 - 1997-2003 :: 2000 - Run Rough - Big Hose At Rear Of Upper Intake?
I just replaced the engine in my F--150 with one from a van that had only 60K miles on it. It still runs rough and misses. Not as bad as the earlier engine that had dropped a valve. While trying to find the problem, I moved a large vacuum? hose at the rear of the engine maybe 1 inch diameter and it nearly fell off the barb at the back It is also connected at the other end to some type of small metal can. When I pulled on this it fell off and the engine died.
Also need the smaller 5/8 in diameter hose at front of air intake tube. I need a size or a pert number for this hose as I cannot crawl back onto the motor very many times due to a spinal problem. I would like to get this hose and then get under the firewall only one time. I am having issues with this truck, bought is used at auction running rough. Replaced engine with one that was supposed to be a good one, but it runs rough again..
I need to add that New platinum [plugs were installed and the coils were off the old engine that had maybe 50 miles on them and were from NAPA. I only hope htis hose is my problem. However I cannot find any part number or anything on it...
Subaru - Legacy :: Leakage On Upper Bolt Head After Replacing Water Pump Gasket
I have a 1990 legacy and just replaced the water pump gasket and now it is leaking out of an upper bolt head on the pump and how to cure this....
View 1 RepliesExplorer :: 1999 Ford 4.0L - Removing Upper Intake
I went thru a 100 posts on "Intake gasket" search but I couldn't find any repair information on the 4.0L intake gasket replacement. I'm having difficulty pulling the upper intake off. All nuts and connections have been removed except for the egr tube that's connected to the upper intake.
According to another site, u should be able to just pull straight up, clear the intake studs, turn the intake to the left and then up due to the fact the egr tube is curves inside the intake towards the front of the upper intake. No luck. egr tube won't separate from the intake. This is a little long but everything has been disassembled to this point. BTW this is a 4.0L OHV engine
Ford - Explorer :: 2000 - Upper Or Lower Intake Gaskets
Our 2000 explorer xls 4x4 with 4.0 ohv just pop the code for the intake gasket leaking. My question is, would there be any way to tell if it is the upper or lower that is leaking? It has 188k on it but still runs good. I think I can feel a miss in it at idle but it is not a steady miss.
View 1 RepliesFord - Explorer :: Changing Upper And Lower Intake Gaskets
I'm in the process of changing my upper and lower intake gaskets. my question is, the upper intake along with the tubing on the fuel rail are caked with oil/carbon, along with the back side of throttle body. What would be the best way to clean them?
View 2 RepliesFord - Explorer :: 1998 XLT V8 - CEL Has Been On And Off Sporadically - Both Upper O2 Sensors Are Shot
I have a 1998 Explorer XLT with the 5.0L V8. My check engine light has been on and off sporadically for the past two months. Lately, it has been on more than off. I brought it to a local place to diagnose the problem. Both upper O2 sensors are shot. What kind of difficulty level am I looking at if I tackle this myself?
View 14 RepliesFord - Explorer :: 1997 - Rear Springs Replacement?
I need to replace rear spring packs on our
97 Explorer sport 4.0 auto 4x4.
What years should I look for? Will 91-01 packs work?
I know of a 92 4x4 close by that is being parted out.
Ford - Explorer :: 2004 - Upper Ball Joint Boots Are Dry Rotted And Torn
I just noticed that the upper ball joint boots for both uppers are dry rotted and torn! Only 40k miles and the boot falls apart when I touch any portion of it. Is this normal, so much for quality?
Anyway my question is how hard is it to R&R them and do I have time? IOW will the ball joint wear out really fast?
Rust bubbles front of hood both corners, the tranny thing, now the ball joints all within 40k miles. rear glass trim breaks and falls off.
Ford - Explorer :: 1979 - Bolt Pattern Same In F And E Series Seats?
I have a 79 f100 that I am putting 96' explorer seats in. Got the tracks all made, decided to have the seats re done as a cat pissed on them.
went to talk to the guy doing the seats today and he can get new foam and won't make new foam. So my question which seats whether it be from an F series or E series has the same bolt pattern as the 96' style seats. so I don't have to make new brackets. Will the fox body mustang seats work as well?
Ford - Explorer :: 2004 - Lower Strut Bolt Stuck
Was replacing the struts and front ball joints on my wife's '04 Explorer last week. I get to the last one (driver's side front) and the lower strut bolt seems to be frozen to the bushing. I heated it up and beat on it a little bit. Nothing. Just wondering for some other way or am I going to have to cut it out?
View 3 RepliesFord - Explorer :: 1997 V6 - Whole Rear Suspension (Shocks) Completely Destroyed
I Just bought a 1997 Ford Explorer V6 4WD and I noticed after the I bought the truck that the whole rear suspension (Shocks) were completely destroyed. I failed to notice this during inspection of the car because it was parked very close to a wall so i was unable to see the area. Now I do know a bit a about cars but I no professional, It seems as if this whole section of the car just rotted out which is surprising because the rest of the car seemed OK. So now my question what do I need to buy in order to fix this I am not sure it seems like there is some sort of cross member that bolts onto the frame that connects the two rear shocks. What it looks like?
View 8 RepliesFord - Explorer :: 1997 - Right Rear Window Motor Works In One Direction?
I have a 1997 ford explorer, the passenger side rear window only works in one direction, I have tested motor and it does work in both directions reversing the polarity, checked switch by checking voltage on each prong of plug (where motor plugs into harness), and does get 12 volts on each line as switch is being activated,I think there may be a ground problem on the one side that does not work, where to start looking??
View 1 RepliesFord - Explorer :: 1997 4x4 - No Running - Shudder In Rear Tire - Front Never Spin?
My Explorer is a 1997 with the control trac 4x4 system. It's only purpose in life at the moment is to plow snow and its been doing that quite well. I typically leave it in 4lo all the time. Every once in a while, I will switch it to the other modes to ensure they are all working.
Today I was plowing and it looks like I'm getting nothing, or next to nothing to the front wheels. There is some shudder if the rear tires begin to spin, but the front never spin, or lock up. I can feel/hear the transfer case shift when I change modes between auto/4hi/4lo as I usually do, but the front wheels just are not doing their job. All three modes are not driving the front wheels.
The transmission was rebuilt a few years ago, and it's shifting fine. I'm suspecting the transfer case. Only my OD light is flashing, but it only does that once in a blue moon. I plugged my code reader in and it could not read those codes. I was able to clear the light though.
Ford F-150 - 1997-2003 :: Coolant Leak On The Upper Intake?
I have a 1998 Ford f150 4.6 2x4 i have a coolant leak on the upper intake. It comes out on the back left of the intake through a metal pipe. Well where the metal pipe is (pressed in) to the intake. Now i talk to the guy at ford dealership in the parts he said it is called the (heater pipe). He also told me that the part is 21 dollars but I have to press it in and if that does stop the leak he said I would have to buy a new intake. Now here is the problem I can not find any info regarding this heater pipe. I don't know how to remove it properly, why it is leaking. I can't find it in the handbooks that i have read so far.
View 14 RepliesFord F-150 - 1997-2003 :: 2001 - Upper Control Arm Cam Bolts
2001 F-150 4x4 5.4L. I am going to replace the upper control arms this weekend. I noticed that there are regular bolts with no cam washer installed. I have read conflicting info on whether the cam washer set up is needed. Do I have to install these or can I just put the old bolts back in just like they are. When I replaced the uppers on my 1997 T-Bird I put in new bolts but there was no mention of a cam washer setup for it anywhere that I saw. What would be the problems if I just reinstalled the old bolts. Right now the truck drives straight as an arrow but the lower ball joint on the driver side is shot so I will be replacing it also.
View 2 RepliesFord F-150 - 1997-2003 :: LED Mounting Bracket Install On Upper Windshield Area?
Installing LED mounting brackets on the upper windshield area? It seems like no one has brackets for the 97-03 F150 which is surprising. I'm not really interested in the mounts that go into the roof and I'm trying to find brackets that attach along the side of the upper windshield area.
I'm looking at mounting brackets that look like this : [URL] .....
Ford F-150 - 1997-2003 :: Upper Ball Joints And Parking Pawl Adjustment
Truck is 1997 ford f150 2wd. Needs an upper ball joint. they all look the same on parts sites. I think there is a recall on the parking pawl adjustment. I lubed up the linkage and sometimes my truck will not engage its parking pawl...
View 14 RepliesFord F-150 - 1997-2003 :: Flywheel To Crank Bolt Stripped Out
I have a problem my slave cylinder went out on my f150 so my buddy and I decided we were going to fix the problem. But while I was in there I figured I would replace the clutch, pressure plate, bearing, rear seal, and obviously the cylinder. When I was putting the flywheel on the "first time" i must have stripped out 3 holes because of not having the flywheel properly aligned. So I tapped out the holes to clean up threads and when we finally aligned the flywheel on the crank to right position I went to go torque down all the bolts three of the bolts would just keep on spinning in the hole. Now keep in mind I replaced all the old bolts with brand new ones from the dealer. What can I do to fix this problem I need my truck back asap!!! Can I go to a longer bolt to hit good threads or what do I do? I'm worried about my motor going out of balance if I mess something up here!!!
View 6 Replies