Ford - Explorer :: 1997 AWD - Brief Rumble Every Now And Then
Jun 2, 2016
My 'new to me' '97 Explorer has this odd 'rumble' every now and then, as if I just ran over some rumble strips. Very brief, maybe a second or less, as if I hit 5 or 6 of those bumps. It is a V8, XLT all wheel drive and I'm not familiar with it. Is this something I need to get looked at soon or is it just one of those things with the AWD. I only driven it a few times so I don't see a pattern and all else is great. Its a tight truck with less than 100K miles and I really enjoy it.
View 7 Replies
Advertisement
My wife's Explorer 4x4 has a noise in the front at around 100km/h. It is not detectable below 90km/h. Its not noticeable from a standstill until around 100, then you hear it a little. I find I can make it more noticeable if I vary my speed from 110 to 105 up and down, then its easier to hear. Once you get below 90 km/h you cant hear it at all.
I have a broken leg right now, and I normally do ALL my own work so I'm a little-limited mobility wise at the moment.
I'm suspecting a wheel bearing. I put the Explorer in the garage and my son jack up both wheels on the drivers side. I started the engine and SLOWLY accelerated up through the gears to 100. I know the hazards with this as I've done it with other vehicles, but this was the first 4x4. Then we jacked up the passenger side (after lowering the drivers side) and did the same thing. I could slightly hear/feel the rumble when the passenger side was jacked up.
I did drive the vehicle on my outdoor ramp/pit so I could use my crutches and get underneath to have a look. I grabbed the cv axles and they feel solid. The propeller shaft was replaced last year, and the cv axles look brand new. (bought the vehicle off a friend two years ago.).
So, are my suspicions correct, is it the pass. side wheel bearing? The Explorer has 294000kms. Never did test it on corners as I didn't want to swerve back and forth on the highway with the amount of traffic.
View 4 Replies
Care finally runs well and passed inspection. So I can legally drive it at speeds. Noticed what feels like widely space rumble strips when coasting 2003 explorer. I am now trying to check all my fluids ... trans seemed a bit low (PITA), rear and front differentials seemed full... but should they be checked with the engine running or off??
View 14 Replies
I have a 2003 Explorer.... 4wd..... and here's my story.. I had a tire blow out (front driver side) and I took it to a tire chain to get it replaced (it was the closest thing to where it happened and I had to get to work)
After the tire was replaced, the truck started to rumble in the front and seemed like the brake was being pressed while I was driving. I called the chain tire store and told them my truck was not doing this prior to them replacing the tire. They said it was fine because I was riding on a better tread tire and the remaining tires were worn.... (okay..maybe so?)
I drive 80 miles one way to work....the whole way there...rumbling and this 'brake applied' feeling. Worked my shift...drove the 80 miles back home...same thing.
Took truck back to store....they said that it was the Front Drive Shaft had cracked at the Transfer case.... I've asked a few people and they think it's just the ABS still locked because I was traveling a high rate of speed when my tire went out. I think the tire store chain screwed up when they replaced the tire....
View 3 Replies
04 explorer, When traveling under throttle the thing runs smooth, when letting off accelerator, there's a rumble from, what seems like, the rear of the vehicle, when I press the accelerator, it almost "clunks" and acts fine once it's under acceleration again. Should I suspect my rear end gears going out, or something simple like a universal joint.
View 1 Replies
Had the torque converter replaced twice on my 2007 Explorer Limited last December. Ford dealer did it once and then there were still issues so they had to replace it again. All seemed fishy to me.
Now a new issue that sounds like driving over rumble strips. Torque converter?
View 1 Replies
I want to put a flowmaster system on my 1997 F250 with 4.6L engine. The muffler shop says i won't get alot of sound out of it because of the OEM Cat Convertor on it. Is this true? I'm not looking for something that will rattle the windows a mile away, just a nice rumble at idle and a good tone when accelerating. The muffler shop suggests a 3" in and 2.5" duals out using a 40 Series muffler.
View 5 Replies
I have a 99 f150 5.4 and i am pretty sure I have a cop issue. I have changed a few over the past few years and this one is acting about the same. The other day i felt a slight stumble but it went right away and drove fine. Well after heavy rain all night i went to take the kids to school and it was stumbling and acting like it was not firing on all cylinders. CEL came on and got the code read at the auto part store. Well driving it home it just cleared and drove fine. So i checked the #6 plug and changed the boot on the coil but all the same symptoms came back. It is the original coil so i am figuring that it is bad.
View 3 Replies
I came home from work truck was running decent got up in the morning to start it up. Tried to start up was real rumbly and died got the same twice then went to just cranking over not getting anything else tried spraying some starter fluid in air and it would try so assuming its firing abd possibly gas related ...
View 4 Replies
I have a 2000 f150 lariat. Mo problem started about 2 weeks ago. Around town its fine but when I go over 50 mph it feels like I'm driving down the rumble strips on the highway and after a couple miles it just smooths out and its fine! Yesterday I went on the interstate and it did the same but this time I ran up to 85 and the vibration stopped.
I had another motor put in about 2 months ago, #4, and he changed my rear u joint as well. I replaced the rear passenger side wheel bearing a couple months ago but there seemed like a little play in the axle still but not bad. I've been to the dealer and a few other mechanics but it doesn't do it all the time and they couldn't find what is wrong.
View 6 Replies
After replacing a faulty spark plug wire on my '97 explorer, I started the engine (4.0 liter pushrod) and noticed the idle much lower than it was previously- to the point it now borders on stalling. The wire I replaced was on the right side (if facing engine from front) closest to the firewall. I thought I may have worked a vacuum hose loose when feeding the wire under the intake, but I checked and checked and saw nothing amiss. What I may've did (if anything) to cause this problem?
View 7 Replies
Have a 97 Explorer 4x4. lately when I start the truck it has shifted itself into 4x4 low. I had disconnected the battery for a few minutes, re-connected and the truck was back in auto. This no longer works and it is stuck in 4x4 low. Mechanic wants to replace transfer case encoder, but says more diag needed after to replacing encoder motor to determine internal failure and may need more work. Can I simply have the 4x4 low disengaged manually?
View 3 Replies
Just got this vehicle a week ago. Test drove before I bought but that drive was fine. Then after driving I started have a popping. Started paying attention at this point and noting what happens when.
It seems I don't have any problem at all until she gets warmed up. I can drive about 20 miles with no problem. Then the OD is Off light starts flashing. Then when I decelerate to stop, I have a big popping at exactly 20 mph. I then have 2 smaller pops once I take off from my stop.
I started searching online everywhere to determine the cause. I am a female whose daddy taught them just enough not to be completely stupid, but not near enough to be able to fix my own car problems. I thought from what I've read that this issue might be a torque converter. I do have a hum after a while that sounds like road noise....like I saw one other person post about bad TC's. But I haven't seen any posts that address the popping.
View 1 Replies
I just bought a 97 explorer and the abs light is on is there a way to pull the codes without an abs scanner?
View 3 Replies
I have a 1997 Ford Explorer with a 4.0 SOHC engine. It bogs down and won't go over 20 MPH. I'm showing codes P1405 and P1151. Would either of these codes cause that issue? I'm not even sure how to start diagnosing this.
View 1 Replies
The serpentine belt on My '97 Ford Explorer broke apart while driving. I pulled over immediately and got to work on fixing it. I noticed the Idler was bent so I bought a new belt and idler. The Idler wheel was busted but it didn't mess up the bolt so that was an easy fix. I noticed after putting in the new belt that the tensioner wouldn't hold the tension so I bought a new one to replace it. I installed the new tensioner, even though it fit slightly differently than the old one. I was assured after going back to the auto parts store, that it was correct.
The car turns on now and sounds fine, but I can barely turn the wheel. What to do? Could the generator wheel, crankshaft pulley, or something else that has the serpentine belt attached to it need to be replaced as well? What should I do next?
View 19 Replies
My 97 Explorer 4.0 SOHC has started to bog down when I press the accelerator. It feels like their is interference with the exhaust. I has a new muffler and there are no holes in the exhaust system. When I stop at a light or in traffic, it will stall. I have to keep the RPMs at 1000 while holding the brake. There is no check engine light on. Where I should begin to look?
View 6 Replies
My son's explorer, 4.0 automatic, developed a problem during a 90 mile trip on the freeway. Driving along at 75 MPH with the cruise set everything seems fine. As soon as he lets of the accelorator the engine drops to idle speed and a noise comes from under the truck that sounds like an old siren, starts low pitch and gets higher and higher. The noise stops when he touches the accelerator applying power to the drive train. The transmission shifts and pulls fine, no slippage. He said that for a while the 4WD light on the dash has been flashing six flashes, pause, six flashes.....a steady code.
View 5 Replies
Have a 97 explorer 4wd xlt push rod. The key will not turn the engine off( when the unit is hot) with head lights on, I turn key off engine runs, i reach over and turn the headlights off engine will shut off. Start back with the headlights off the engine will shut right off, but if I turn the headlights on on while it is running and leave them on it will not shut off, unless i turn headlights off.cold start does fine.. I can turn ign key to the off position radio stops playing, so I know it is not the the switch or rod. I was going down the highway and lost dash lights and taillights the other day I moved the switch a little and they came back on the ign switch worked perfect that day.
View 2 Replies
My explorer starts fine some days and others it just wont. No codes, have replaced fuel pump. Rail and starter.
View 11 Replies
On this '97 explorer, the fan is running, but no air out the defrost, ac, or heat vents no matter what position the switch is in. I tried to read the sticky on the air door, but the link is broken.
View 1 Replies
