I have a 96 explorer, and it will just shut off, but restart ok. V6 push rod motor. It has only done it 2 times in the last 2 weeks. One time I was driving slow, been running for about 20-30 min
The other time I had left it run, while I ran in to pick up a pizza, and my wife said it just shut off, had been running around that day , but started it about 15 min earlier. I fill it up before it hits 1/4 tank....
My friend has a 2004 explorer v6 150k miles. Randomly shuts off while normal driving just going down the road, and when you try to restart it it starts up and runs fine. This used to happen every few months and is getting more frequent. The only code it has is a lean code from the o2 sensor, I'm trying to get more info on that but it's been like that before this problem started and possibly just a bad o2 sensor. Where to start and any know issues that would cause this? Sounds like a wiring issue are there any spots in particular prone to chaffing?
View 3 RepliesThe car is about a week old. Today, the NAV system (ML version), re-started a few times and then shut completely off. Re-starting the car does not work. Got a totally "off" screen and no sound. 2014 350?
Is there some way to reset it or turn it back on? I can't imagine that a brand new Lexus would have this sort of issue.
Module or cam/crank sensors most likely? How difficult are the sensors to replace if module doesn't fix problem? 120 k mileage.
View 16 RepliesFor those of you who have not purchased a new car for a while and are considering doing so in the near future I want to share the recent service experience I had for my 2015 Jeep Cherokee. I don't know if my experience was typical but I suspect it is.
I took my Jeep to the dealer for a routine service (LOF and tire rotation). The total time at the dealer was about 4 hours. Of that time, about 2 1/2 or 3 hours was spent in updating the software for the various computers. It had never occurred to me that computers were that pervasive in new cars.
Attendant to that, my Jeep has the 3.2L V6 engine, which comes with start/stop technology (when you stop at a stop light the engine shuts off and restarts when you take your foot off the brake). After the service was completed I noticed the start/stop function had stopped working. I contacted the dealer. The customer service representative spoke with the service technician, who contacted Chrysler. It seems that all of the software updates (there were a total of 6 of them) may take 3-7 days to become fully integrated into the system. I was told to wait a few days to see if the problem rectified. Sure enough, when I drove it today it had.
What's the fix for a 1996 Ford Ranger when the engine shuts if the vehicle is put in reverse? (It will run in drive, but not in reverse; fuel filter, air filter and vacuum hoses have all been checked).
View 2 RepliesI have 2001 ford explorer sport.. it idles very low in drive and reverse and then shuts off.. What has been replaced:
1. Torque converter
2. All new plugs n wires
3. Map or mass sensor
4. Iac valve
5. O2 sensors
6. Fuel filter
7. Air filter
8. Throttle valve/sensor
It does not run bad only when u come to a red or stop light.. Had the vacuum tested and no vacuum leaks.. also no check engine light has come on and no codes have popped up when tested..
I drive a 2005 Ford Explorer (automatic) with 84k miles on it. Recently when I was driving on cruise control at 35 mp/h down a hill and applied the breaks to make a turn, the engine completely shut off. The lights came on, the power steering went off, the engine had shut off. I pulled over, turned the key off, turned it back on and it started no problem. I drove it for 3 days without problems (and without using cruise control of course), then I took the car to a shop. They ran diagnostics on it, test drove it, but couldn't find anything wrong with the cruise control or the transmission. I don't think they tested this driving downhill as the shop is not in a hilly area. Tonight, I went down the same road again, 35 mp/h in cruise control, slowed down for the same turn, and the engine shut off again exactly the same way it did before. What this could be?
View 7 RepliesWe bought it and the dude that owned it cut the radio wires and messed with the wiring everywhere because he thought he had a short. I've hooked up the radio and everything and it does the same thing. How do I bypass to make it stay running.
View 10 RepliesMy new-to-me Explorer appears to switch to 4WD high but refuses to engage 4WD low. And now I have the 6-times-flashing 4WD and 4WD low dash lights when turning the ignition on.
I used the correct procedure: Stop the car, put it in neutral, and switch to 4WD low. Nothing happens.
I looked for a ground wire from the top of the transfer case to the chassis. I can't find any such wire. All the under-hood fuses are intact.
In the process of looking for the ground wire I discovered a capped 3/8 inch or so vacuum hose about 6 inches long with a right angle fitting at the front of the transfer case. I also found a capped 2-foot-long hose of similar size connected to the top of the front differential. What the heck are these hoses? Has somebody intentionally disabled the 4WD?
I am reasonably adept at electrical repairs, troubleshooting, and modifications..
My 1996 Ford Explorer makes this dreadful droning noise - but only when the outside temperature is above 78 degrees and the engine is warm. This is summer 3 and it seems to get louder and louder each year. The doing is loud. I am embarrassed in parking lots. It does not matter if a/c is on, or the fan. The noise goes away with throttle. Which may mean the engine vacuum is involved in the noise.
View 4 RepliesMy 96 Explorer has been sputtering on me. I took a right turn one day and now its sputters at acceleration. It has a new fuel pump, filter, injectors, coil pack, plugs, wires, idle sensor, EGR valve. Also, all vacuum lines are good and not cracked or broken. My mass air flow sensor is also clean and clear. I have done all my own repairs on my cars and trucks all my life and thought I was good at it (not so sure about that now).
View 1 RepliesParked in driveway and 2 hours later it cranks but will not start. Pushed on fuel rail Schrader valve and it squirts out. Turn key and the fuel pump runs for 2-3 seconds then off...... Thought I had fuel... assume electrical. Read posts last night and thought crank positioner pickup was a good place to look. Took spark plug leads off #1 and #4 at coil and set a 1/4 steel dowel in each so they were 1/2 inch apart. Crank motor and I get spark out of coils so I assume the plugs are getting fire... Took off intake hose and shot ether in the tube while cranking... no fire or pop at all.
Where to now ? Seems like I have fire to the plugs, and fuel available but will not start. I have only one code and that's PO1116 coolant temp out of range..I don't have a cam sensor code or a crank sensor code...I thought they might effect the timing ? With spark at the plug wires, you would think I would get a "POP" now and then, especially with the ether ?
On my 96 explorer the speedo most always reads 50mph. It goes to this as soon as you take off. You can be doing 5mph or 75mph and the speedo goes to 50mph and stays there. Everything else on the instrument cluster works. Is there something I can replace on the speedo only or do i need to find a good used instrument cluster?
View 1 Replies1996 Explorer xlt 4.0l ... I ran into this issue a few years ago on a drive up through the mountains. Had the tranny replaced shortly after.
Rebuilt the engine once due to leaking head gasket.
Rebuilt it again 2 months ago due to leaking rear main seal.
Had a new torque converter installed during last engine rebuild, so tranny has been shifting and driving like a dream.
Just drover about 30 miles on highway, all pretty flat. OD light started flashing. I didn't notice ANY change in the way it was driving, sounding, shifting... anything! I know this is some sort of oddball error with this transmission in this vehicle, but i need to know if it requires further investigation.
Also, sometimes upon starting up (i am a pizza deliver, so i often shut it off and start it again 1 minute later) the OD and (i think) the 4x4 light flash at the same time, and my windows wont work for around 15 seconds. I've also noticed that my ABS will sometimes kick in randomly on dry ground during slow stops.
I am not in the mood to just start dropping cash on random sensors or modules or repairs if i can find any solid evidence of an issue (i've been battling an EGR issue for 4 years). I was thinking maybe the vehicle speed sensor?
I'm replacing the oil pan gasket and the new gasket came with a half moon plastic seal. I noticed that there is a grove in the new engine at the rear of the engine but the old engine does not have this grove. Looking for info about this seal, do I need it or not?
View 2 RepliesI recently acquired a 1996 Ford Explorer XLT with a 4.0 OHV engine 62K mile. During vehicle evaluation I found a small coolant leak on coming from the timing cover gasket. I had the timing cover gasket and water pump replaced by a trusted mechanic.
Upon receiving the vehicle from the shop I immediately noticed wildly fluctuating engine temps, going above normal to nearly overheat and then suddenly dropping too cold. This would happen as I am driving at speed or at idle. I replaced the t-stat with a fail-safe type and find that it still does the temperature fluctuation. Called mechanic and he recommended burping the cooling system. Freed air in the system by topping off during cold start and adding coolant till full, and the condition seemed to improve but not fixed.
The fluctuation is much more minimal now, but the engine temp is always lower than normal on the gauge display. Before the initial service, temp gauge read dead center at operating temp always. Now it always runs colder, no matter what. The heater works too, and sometimes it seems to affect the temperature when I engage the heater during driving after warmup, the temp will start fluctuating.
I noticed that the upper radiator hose is much hotter than the lower radiator hose. In this case, after a drive the upper hose had surface temp of 200 F and lower hose had surface temp of 130 F. I have heard of backwards water pump manufacturing and I am beginning to think that is culprit. I can see the flow indicators on the upper hose showing coolant flowing from the radiator to t-stat, but hose surface temps testing suggest that it is operating backwards to me. I do not have the original water pump to comparison.
It became apparent that the fan clutch may be sticking some. When I cold start (30 F ambient) the fan runs at high rpm for several minutes before slowing. Even warm start fan will spin up with engine until second or third gear, then spin down. Is that normal operation?
I am having a problem with my 96 ford explorer.
Usually this only happens on warmer days, but after a few starts, my car will suddenly not turn over. I have found that the only solution to starting it is by pumping the brakes about 6 or more times, fast and hard. Its not the battery because all lights and everything work.
Something it may have to do with, I just found out when going to get my car smogged, my monitors reset everytime I turn on/off my car.
Was driving into town today in my 96 Ford Explorer XLT v6 4wd, when I noticed my O/D off light flashing. I thought to myself, "Another problem I have to bash at with a wrench to get going again." I figured that meant I'd be stuck with gear 1 and would burn some extra gas on the ride home, but after parking and running an errand, woe behold me but my car won't start! The starter turns, but no other noises come out of my now very-large paperweight. I've tried shifting into neutral, moving the car to get the gearbox turning, starting the car in neutral and park, yet the stubborn car remains dead. Am I drawing a connection between the light and the failure to start where one need not exist?
View 4 RepliesWhen car is started, volume on radio is very low. As the car warms up, the radio volume increases. What do I check or fix?
View 13 RepliesHe has a 96 explorer and his ac compressor clutch was cycling on and off. So he went and bought 2 20 ounce cans of 134a and proceeded to add it to the evaporator service port. Of course a lot of it sprayed out side of it as it did not fit well (duh). So he has no Idea how much he actually got in there out of the 30 or so ounces he dispensed. He is laughing at himself with me on this. He says hi ahead of time
I have access to good gauges and a reclaimer and vacuum as I work sometimes for a residential ac guru. So what to do? I was thinking the evaporator should be changed out but I want a second opinion. Then vacuum and add new 134.