Ford - Explorer :: 1992 Died When Tried To Start And Then Restarted
May 6, 2014
I purchased a 1992 Ford Explorer Eddie Bauer edition two weeks ago from a private dealer. Last week I went to start the car, and it started, but then turned off almost immediately. I dismissed it at the time saying I did not turn the key long enough or far enough because when I tried it again, it started.
However, this morning (05/06/14) it turned itself off again. It was on for about a second or two before it died. I started it again and pumped the gas. It started for me but it sounded rough like it might die again.
I am not sure how to fix this. The previous owner did not mention that there was any problem. I am thinking that I'll either need to replace the battery or the spark plugs.
View 6 Replies
Advertisement
Picked up another 92 extended! Seller's mechanic thought ECM died. When you connect the battery, the fuel pump runs, steady. 167K, same as my DD van! Plans are to pull the trans and swap tires first, and eventually pull the motor and freshen the seals and gaskets, and a timing chain. I would like to have it run first though. I'll take pics after it's hauled home.
View 3 Replies
This morning, I started my truck to go somewhere and less than a minute into my drive, the engine suddenly died. I tried cranking it again to which it started but less than a second later it quit again. That's when I noticed my FMP on my SGII was at 0v. When I got it back into a parking spot, I pulled the FICM and tested the connectors as well as the relays and they all were normal.
I decided I will be pulling the FICM again tomorrow and I will be sending it back to FICM repair.com for them to look at as I got a new one from them about 8 months ago. However if it is in case the wiring harness, where is a good place to look. I don't think it is the wiring harness as it seems to have voltage at the connectors.
Also this may be related but earlier this week, my Scangauge froze and I unplugged it and plugged it back in and it didn't connect to the PCM until I reset the SGII to factory settings. I wonder if this is related?
View 14 Replies
I have a 92 Deville. I drove a pretty good distance today and on the way home stopped at the store and left the car on in the parking lot. I got in and the engine died as I tried to pull out of the lot. When I try to start the car all the lights come on but nothing happens, no clicks or anything. Lights don't even go dim. Could this be the alternator? I know that the starter suddenly dying won't cut off the engine like that. Everything seemed fine before idk what gave out?
View 6 Replies
Yesterday I drove my mom's 02 explorer to the gas station to fill it for her. After filling, I started it. It ran for several seconds and then died. It wouldn't start right away, so I let sit for a half hour, and then it started and I drove it 10 miles home. What is going on?
View 6 Replies
I have a 1998 Ford Explorer. It was running fine until last Mon. On my 3rd start of the day , it wouldn't stay started long enough to get into gear; sometimes it sputtered violently. I tried starting over the next 2 days with the same outcome so I towed it to mechanic. They replaced spark plugs, wires & started (because it was throw lower voltage than normal). It ran fine the short distance home. The next day, it started fine but sputtered in corners/lower speeds. About 12 miles into the drive, which was at ~60 mph, my auto died and wouldn't start again. What's going on? Could it be the fuel pump?
View 1 Replies
Was driving the other day and it just died and wouldn't start back up. It has fire and is getting gas. It's a 4.0 Sohc...
View 3 Replies
I have a 92 ranger 6cyl 4L. The truck stopped running while driving then kicked on again, it did this several times over about 20 minutes then finally died and now I can't get it started. I recently replaced the fuel pump and filter and spark plugs and wires. I get spark if I ground the plug and some gas will pour out of the fuel pressure test valve when I stick a screws driver in. When I check engine codes I get an all pass. Truck will turn over and sometimes run for 2 or 3 seconds but that is it.
View 2 Replies
Why is my 1992 ford explorer self accelerating between 15- and 25 mph?
View 1 Replies
I have a 1992 Toyota MR2 and the other day I was driving home on the freeway. I started to hear this slight ticking noise from the engine compartment. I let off the gas and the noise stopped. I decided to pull over at the next exit but when I steeped on the gas again the engine died. No idiot lights on or gauges going wild that I remember seeing.
Now it won't even attempt to start. When I tried to roll start it, (it's a manual transmission) the wheels were locked up and actually tried rolling backward. When the car died on the freeway it just rolled to a stop so I know the tires worked fine when it died. What this might be? By the way, it's a non-turbo, 2.2 liter.
View 11 Replies
VEHICLE: 1992 Ford Explorer, 4.0, 4wd Automatic, CALIFORNIA EMISSIONS w/ 59,000 Miles...
PROBLEM: Engine rolls over great, BUT No Spark, No Fuel
Here are the tests I've done:
- Each and every relay √
- Each and every fuse √
- Ensure inertia switch hadn't popped √
- Directly connect 12 volts to pump & pump came on √
- By-pass inertia switch √
- Replace PCM √
I'm thinking it's time to start checking grounds and chasing wires....
View 14 Replies
1992 Fod Explorer XLT: When I attempt to turn over the engine, the flywheel spins, but the engine doesn't. This is a very gently driven vehicle. I drove home hone day, backed into the driveway and unloaded the groceries. The next morning, when I tried to start it, the engine will not turn over. I dropped the starter and tested it--all good. While I had the starter off, I found I could spin the flywheel freely--appears to not be attached to the engine. It's tight with no play whatsoever. Last year I had a new flywheel installed--something I would do myself, but decided I'm at the age, I'm just not up for it. It's been running great for 18 months with no problems. There was never a noise. This just happened one morning. I thought the crank may be broken, but that seems unlikely since it was driving great until the next morning.
View 13 Replies
I am going to look at a 92 Explorer soon and the owner says the transmission is shifting early.... I'm not exactly sure what they mean by it and I haven't gone and test drove it myself yet, I'm just trying to get opinions on what to look for and hoping it doesn't mean the end soon to come for this tranny. I was thinking maybe the vac. modulator could be the issue but I don't really know much about these Explorer's, as I've only owned one for about 2 months. It's a 92 4WD.
View 2 Replies
I have an '92 Explorer 4X4 with a stuck emergency brake. I have tried tugging on the lines from the back of the truck (where the line splits into two beside the frame). The brake is stuck in the on position, and when I pull the release nothing happens. It has been cold here lately, so i thought they were frozen, but after pulling the release lever, it seems like a mechanical issue.
Any temporary solution that get my truck drive-able and to my mechanic for a closer look. I am not very mechanically inclined but it seems to me that the release lever is pulling at nothing and not moving the cog to release the actual emergency brake.
View 1 Replies
I have a 2007 explorer that died while i was driving. We have changed the battery, alternator, spark plugs, fuel filter, and have checked the fuel pump, starter, throttle body. The truck cranks but wont kick over.
View 6 Replies
I have a 1992 for explorer XLT 2-wheel drive Automatic 4.0 engine. The starter started grinding against the fly-wheel. Changed the starter and the same thing happened. There is no shim for this starter. I took it down and checked the flywheel--as much as I can see through the starter mount hole and the teeth on the flywheel are great. There is only the slightest point of impact where the starter is just grazing the flywheel.
I also grabbed the flywheel to look for looseness, thinking it might have broken and/or warped and I just can't see where it broken because of the small hole. It's solid! It's as if the whole thing just moved back about an inch and a half... I texted both the old and new starters with jumper cables, and the make certain, I took them to the local parts store and they also texted them. While both of the starter were fine, I'm not!
View 4 Replies
1992 Ford Explorer XLT 4wd 4.0L (California vehicle) runs good for about 15 minutes, then suddenly starts 'chugging,' loses power, and check engine light comes on. After sitting overnight, it will again run good for about 15 minutes, then repeats the problem.
This problem began AFTER smog check test failed (it ran smoothly all the time before) and after, as was recommended to me, I replaced the 02 sensor. (Failure of smog check, it turns out, was more likely because, unknown, a 10" piece of exhaust pipe was missing, so Catalytic Converter was not connected to the tailpipe).
I had a mechanic scope the Explorer but he could not determine a specific failure from the codes, although he suggested possibly it's the missing 'Octane Adjust Shorting Bar,' or maybe the 'crank position sensor' is bad, but he could not give a diagnosis.
View 6 Replies
I have a 2002 Ford Explorer and besides the seemingly oh-so-common annoying crack in the tail gate, I have another issue I consider to be major. Recently, on a short trip to the store, I hit an incline in the road of a slight degree. At this point I noticed the RPMs going wildly up and down and ultimately the truck died. I tested this out on a few drives and what I've noticed is that if I'm on a flat surface, the truck seems to be okay. OR if I do hit an incline, either lifting of the gas or powering through it seems to work...although neither of which is a long-term solution. I just lost my job a couple weeks ago and the idea of taking it to a mechanic scares me as I'm very limited on savings. I don't really know where to start.
View 6 Replies
My 92 Explorer 4WD has a coolant leak somewhere at the front of the engine above the water pump. I assume it's the lower intake manifold gasket leaking. The engine has 170k miles. I'm also seeing a small amount of white smoke, possibly steam when the engine is running. It's somewhat heavy when I start it up but mostly goes away once warm, so I suppose it could be steam, but could be coolant from either a head gasket leak or lower intake leak.
I also get a lot of water from the exhaust dripping on to the floor and the smell of the exhaust could be that of coolant, it's hard to tell. There is no coolant in the oil. I was wondering if I should go ahead and change the head gaskets while I have the intake out. Is there anyway to be certain the head gaskets are fine? I'd hate to change the intake gasket to find out there's a small leak in one of the head gaskets.
One other thing: I failed emissions because my CO was too high, but my HC and NOx were very low. Could this be an indication of coolant entering the combustion chamber? Just wondering why my CO was so high yet everything else passed (Massachusetts emissions).
View 8 Replies
My daughter was driving down the interstate doing 70 mph when her explorer lost power and died. It will not re-start. Checked the DTCs and there were no codes. This same thing happened about a year ago and she had it towed to the dealership. After 3 weeks, they called and said to come pick it up. They said they had no idea what had been wrong but it was running. They replaced crank sensor, cam sensor, cleaned and checked several others an it still would not start. Then one day they sent one of the flunkies to move it back into the shop and he started it up and drove it in! They checked several more things but claimed they really didn't know what was wrong or why it started running. Now it has done it again. I suspect it may be a faulty ECM.
View 3 Replies
Something is snapping/clunk in 4 wheel about every 20-100' driven on the left side. Slightly notice it in 2 wheel but 4 it's loud and you can feel the clunk. It's almost like when you feel the transfer case bind up, yet feels like it's right in the left side, up front. Yes I have to put new tires and rotors up front, upper and lower ball joints and inner tie rod on the right side. U joint in front drive lines feel solid.
View 4 Replies
