Ford - Explorer :: 1992 - Clunk In 4 Wheel On Left Side Like The Transfer Case Bind Up
Feb 4, 2017
Something is snapping/clunk in 4 wheel about every 20-100' driven on the left side. Slightly notice it in 2 wheel but 4 it's loud and you can feel the clunk. It's almost like when you feel the transfer case bind up, yet feels like it's right in the left side, up front. Yes I have to put new tires and rotors up front, upper and lower ball joints and inner tie rod on the right side. U joint in front drive lines feel solid.
View 4 Replies
Advertisement
I am completely stumped. 4.0 SOHC 145k miles.
There is a clunk that is coming from the transfer case (at least thats what it sounds like) when im driving in A4wd. When i transfer it over to 4HI, the clunking goes away. The clunk happens on acceleration AND deceleration. I have replaced wheel hubs, upper control arms, stabilizer end links....
Checked every other piece of rubber or bushing or connection or CV joint under that thing and can not figure it out.
Also, I just replaced the transfer case control motor and the clunk is still there. Its worth noting that I am able to switch between A4wd, 4HI, and 4LO with no problems at all. I am getting ready to drive this thing into the river.....
View 3 Replies
So long story short I have a 92 Aerostar AWD which I'm pretty sure had the transfer case recall done (97V204000 1992 FORD AEROSTAR Recalls) it has the aluminum driveshaft but a couple of years ago the transfer case cracked and I replaced it with a "New OEM" transfer case off eBay. Fast forward to the present and my van has a strong vibration at 60+ my transmission guy says it all looks good so the vibration has to be from one of the driveshafts. My thought is that I may have got a transfer case without the recall done on it and its warped my driveshaft. I don't really know thats possible or what I could do about it if that was the case.
View 8 Replies
2014. Noticed the feel and sometimes clunk when shifting to 4 high? My house sits up a hill and this time of year, routinely have to use 4X4 to get up. There is a little more noise and vibration than im use to. Usually shift coming down a semi flat dirt/ice road at low speeds, typically about 10mph. Going in for first oil change soon and was gonna ask them to check it out for peace of mind.
View 6 Replies
I just replaced the transfer case BW 4405. And I noticed that the 2 sensors (front drive shaft and rear drive shaft) are bad. What is the name of these two sensors? I'm looking for a brand new ones...
View 13 Replies
I bought a new to me 03 explorer 4.6 tow package XLT 136000mi. Rebuilt aamco trans with 10k on it. Been checking it over before i put it on the road.. No 4x4 but the button lites work and i got into low range once. (Had a hell of a time getting back to high but eventually it did). Question is if there is 12v at the brown wire on the TC the case should be fully locked? I figure when i check it if there is not 12v at the brown wire in 4x4 high i could apply 12v directly with a jumper wire to see if the case locks to 4x4. Am I correct?
View 2 Replies
I keep getting a check engine wrench on the readout, put a scanner on it and got the following code:
P183b transfer case code ...
What this means?
View 2 Replies
My 4WD sport trac was running fine. I took it off road and put it in 4WD. After I was done in the woods. I put it back into 2WD and backed up to unlock. I then drove 2 hours home. The next day the transmission started shifting funny, especially overdrive almost like I was low on fluid. (which I check and I'm not) And the truck sounds like its running ruff. Is my transfer case still ingaged? Do I need to take it in for tranny work?
View 9 Replies
I am working on my grandmother's 2002 explorer and it is stuck in 4wd. I have unhooked the plug that goes to transfer case and also took out the 4wd fuses and still stuck in 4wd. From what I have read on here that the electromagnet inside tc usually fails and does not engage or if the control fails unhooking it will make it so the front drive shaft is disengaged. So since my problem is still there after that it has to be the tc itself and should I replace tc or put a new clutch in it. Also can i take the driveshaft out it looks like behind the coupling is a slipyoke so the coupling would fall out.
View 7 Replies
Originally it would light up on the dash, the hubs would lock, but the transfer case would not shift in to 4 wheel. Followed the troubleshooting I've found, was receiving power at the connection on the shift motor but it was not turning.
So I went and bought a new motor, installed it, still wouldn't turn. (with the motor off the transfer case but electrically connected). So I found a few more replies about the relays, swapped them, nothing.
Removed the covers and manually flipped the connection, nothing. Now my hubs are locked, transfer case is not, and I get nothing when I change the switch on the dash. (no lights, no hub click shift, no 4 low, nada). All the fuses are good, just doesn't work.
View 4 Replies
Looking at another Ex but the owner says the transfer case does not engage. Says it can be locked into 4X4 by crawling under it and engaging it manually by removing a motor [Servo motor ?] Does this mean I would need a new transfer case or just the servo motor ? I know mine did the same thing last winter. It would go into 4X4 and then pop out.
View 10 Replies
Where/how to check the ATF in the transfer case? I found the lower drain bolt,but I don't see anything up higher that looks like a fill hole.
'91 Aerostar 4.0L AWD
View 6 Replies
2003 ex 6.0 limited....300000 miles ...Automatic.Merry Christmas to all.My Transfer case will not shift into 4wd . Dash light for 4wd high and low works .I get no power to transfer case 2pin connector when key turned on.Also fuses 19,27,31,33,34,45,111 are all good when checked with meter.I also swapped 2 relays in engine compartment and no change.4 WD Switch on dash has power on Green/red wire I think it is for dash light and not for operation.
View 13 Replies
Swapped out my transfer case since mine was detonated and now my tranny is running hotter? Drove in town for about 10-15 minutes and noticed my temps climbing and once it got to 180 it felt like it was slipping when moving from a full stop. i went home and parked it. Checked my fluid level and it looked a little low so topped it off while running and went through gears to make sure it was good. Drove again and it still went up to 180 in 10-15 minutes in town driving. Before we swapped the transfer case it was driving fine and went on a road trip 6 hour drive and felt fine. I bought the excursion and it supposedly had a new tranny in it.
View 14 Replies
About 9 months ago heard a strange noise when shifted into 4 wd , sounded like driving over those grooves on the side of the highway to keep people awake.
Had to pull over to stop , as it would not go back into 2wd with the noise still going.
Then it stopped , after shutting truck off and restarting.
Then earlier this year after trying to do it again in 4wd had bad clunking noise and was hard to get back in 2wd , I can here the shift motor engaging and the dash reads in 4wd, seems its not engaging fully in 4wd and not going back to 2wd, its a very bad clunking noise, shakes the whole truck.
View 5 Replies
The dang thing leaks from the fill plug, I been reading about using liquid teflon on it.
View 4 Replies
I had sold my Explorers but just picked up a 2000 Excursion V10 plow truck. It has been hacked and slashed I find cut wires under the dash and hood. I have tried everything to get the 4x4 to engage and no luck. It is used just for my driveway no road driving...
So question is: Can I engage the 4x4 at the transfer case so it will go, and stay in 4 wheel drive. If so do I take the shift motor off or does that big bolt by the motor do anything.
View 11 Replies
I have a BW 1345 transfer case. Does it have the shift in the fly capability? And, if so, what precautions should be taken if shifting on the fly?
Second, where can I get a "plate" or label that shows the shift pattern? I know the shift pattern, I just want to post it in my vehicle in case anyone else ever drives it and needs to use the 4 wheel drive.
View 1 Replies
It has a floor shifter for the xfer case with 2wd, 4wd-H,and 4wd-L, and Neutral positions. It works fine in the 2wd and the 4wd-H positions. The problem is it sometimes slips out of 4wd-L position into 4wd-Neutral, which I have just lived with, but it is annoying. I think I heard this is a known problem with these 1970's Ford xfer cases, and the fix involves removing the xfer case and replacing a part.
View 10 Replies
I have a 99 f150 with a 4.2 manual with four wheel drive I need to replace the speed sensor in the transfer case it looks a lot like the one in the rear end I've called the auto parts stores and they show nothing. What sensor I can use ? I did find one on rock auto that said it was for the transfer case but after looking into there part I found it was for a automatic ...
View 1 Replies
My 97 4.6 ran fine but the 4x4 light came on even when the transfer case lever was in 2wd. Then one day it would not start. It cranked over fine but would not fire. I added fuel but it didn't work. I pulled a spark plug lead and attached a spark plug while I jumped the solenoid and cranked over the engine to visually check for a spark as I have done on older trucks. Well it cranked a couple of times and then it died and won't even crank now, I must've fried something, the batterys fine. If there is a fuse or something? What could have happened when I jumped the solenoid?
View 4 Replies
