Ford Excursion :: Wiring Diagram Of Radio Controller?
Apr 6, 2013
I removed the rear radio controller from the back of the console and installed a power inverter in its place. It fit great and everything went smoothly. I should have known it was too easy... I now have no sound coming out of the rear speakers. I assume there is a way to jump the wires to allow the speakers to work, but I'd need a wiring diagram. Right now I have the controller hooked up and buried in the console, which I guess is fine. It's just annoying.
View 10 Replies
Advertisement
I just bought a 2000 Excursion limited v10 4x4. I'm going camping this weekend so trying to install my brake controller. I found the plug but noticed these wires dangling. I can't see the back of the harness. I'm afraid the PO may have cut them to install a universal harness. How to recognize them? I don't want to buy a ford specific harness if the wiring has been cut.
View 3 Replies
First, need a wiring diagram for the outputs on the back of the brake controller module? I want to check and see if there is a problem with the connection to the rheostat. I can activate the trailer brakes with the slider bar but not with the brakes.
Second, where I can get a new OEM controller that will replace my old one if I can't "Cypher it out"?
View 2 Replies
Got myself a brand new old truck. No radio and all the wires had been cut. I just printed of a wiring diagram from web and went to work I am now on my second one and it has the same colors for two different speakers!! The first one was completely wrong. Looking for a good wiring diagram for a 97 f250 super cab.
View 1 Replies
I am going to be pulling a trailer next week. I bought a raybestos voyager XP controller. I expected it to be plug and play but what I got was four wires. I have heard that there is a plug ready under the dash to plug a controller into directly. I found a gray pigtail with male ends. Is this it? Should I take controller back and get one with the correct plug or is there a harness one can buy or is a stop to my local ford dealer in the future.
View 5 Replies
I'm currently trying to swap out the standard AM/FM/CD for a DVD receiver with backup camera, and need to find out the proper wiring colors and pin position. I'd rather not send it to a stereo shop, as I've seen a lot of hack work by so called "audio installation experts", and besides.. I have a shop and can do the work myself.
I tried looking through AllData, but since my truck is too new, Ford doesn't release a lot of technical info for us in the aftermarket. Looking for a link to a Ford diagram?
View 6 Replies
What is the factory radio wiring colors or know where I can find a diagram?
View 14 Replies
Working on the dang ram 3500... I am needing to add a relay, however, i need to strap the coil of it with a diode to protect the frigging cluster (the new dodges aren't very mod friendly!). My question is, should I add a second diode before the relay to protect the cluster against back emf, or will the one strapped across the relay coil be enough?
Since I am sure you're curious now, the cargo light (light that lights up the bed) gets its power from the gauge cluster of all places. I need to add a relay to the cargo light circuit to drive some other lights, and I am worried the back emf from the relay coil will fry the cluster circuitry.
View 2 Replies
I just purchased everything for my audio and I need wiring behind the radio. I purchased a Audio Control LC6i and I need to know which wires are for which speaker. I tried the Hyundai tech info website but it doesn't show anything when I go into the diagrams. By the way I have no navi just the steering wheel controls.
View 12 Replies
Looking for a wiring diagram for the interior lights? 2004 EB.
Gotta chase down the problem, no interior lights coming on, switch or gem...
View 4 Replies
Ive got a 2004 excursion Eddie bauer and I've got the non-towing paddle mirrors with power adjustment, heated, and turn signals. I want to put the 2008 style towing mirrors on that have power adjustment, heated, turn signals, and have the marker lights but not power fold or power telescope.
How I can wire these new mirrors to my factory wires? I understand that the marker light may have to be separately wired in, but all of the other functions I want to wire in to my existing wires.
View 7 Replies
Currently I have a license plate camera wired always on connected to a 7inch lilliput monitor infront of my center console on that hump in the floor. The monitor is connected to a 12v plug on the dash. In this configuration, I have to reach down and turn the monitor on whenever I want to reverse and im hoping I can make it turn on whenever I go into reverse. Right now, if I turn it on then turn the truck off, the monitor stays on with a bright blue no signal screen which forces me to turn the monitor on, then off, every time I reverse if I want to use it.
Any way to make the monitor turn on/off when I put my Ex in reverse?
View 14 Replies
Looking for the wiring diagram for the circuits on the steering wheel? For some reason, when I hit my cruise control on button, the horn honks...
View 6 Replies
Looking for a link to the fuel pump wiring for a 2000 V10 Ex? I'm trying to pinpoint my no start issue and want to make sure I don't miss anything. I think it goes from 20 amp fuse under hood to inertia switch to relay under hood to pump? 20 amp fuse has power but at the inertia switch I have no voltage, just approx 35 ohms resistance to ground on both outside wires. Does the inertia switch close a ground or should it have voltage?
View 10 Replies
My park lamp circuit is dead. I have tested with a multi-meter and there IS power at the fuse. However, no power at the plug. I have pulled the bumper and found the plug for both the rear taillights (the park lamp circuit WORKS in the taillights) and the trailer wires. Confirmed it is dead there as well.
Both bundles go into the frame rail at the fuel tank, but I not sure which is which where it comes out at the firewall. A web search did not reveal a diagram and the Ford repair CD I have does not list Excursion diagrams.
View 6 Replies
Need a wiring diagram that will show me how the rear window defroster circuit works in my Excursion. I have the EATC, which may or may not be related... not sure. So the diagram would probably need top be from 2002-2005. Obviously I ask because mine is not working (and neither are the mirror heaters since they are activated by the same switch - I think???). I've checked fuses to no avail...
Mine has never worked since I got this Excursion put together last year. I have read some previous threads that mention two different rear hatch glass defroster grids, one being a higher output grid (and different resistance?) than the other. Is there a chance my system is looking for the higher ohm grid, but my window grid is the lower ohm unit and therefore not activating the timer? I only ask this because my electrical system is M/Y 2002, but my back hatch is from a 2000 M/Y.
Also, I get no indicator light when the switch is depressed. I have tried 3 different switches just because I had extras... no luck.
View 5 Replies
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
View 4 Replies
I am in need of a wiring diagram for a 00 ex with factory auto dimming rear view mirror. It only has 3 wires and I think I have them figured out but would like to make sure before making a pigtail to install a mirror I have that has 6 wires.
View 7 Replies
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 Replies
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 Replies
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 Replies
