Ford Excursion :: Vibrating Rotors - Brake Calipers Replacement
Apr 10, 2015
Front caliper replacements--fwd? Person I bought this from said they'd just relined the brakes before I got it. After having it a week, I randomly checked torgue on lug nuts...a whopping 80 ft lbs. So now I have the vibrating rotors. When I back up I hear scraping like a bad set of bicycle brakes against an out of round rim. The pads are pretty thick. I bought new rotors and pads but I wonder if I shouldn't get calipers as well. This X likes to bite me in the butt--something simple is always about 5 times more complicated than anticipated.
View 1 Replies
Advertisement
I replaced my warped front brake rotors a couple thousand miles ago and all was fine but when I went to swap over to my snow tires, I can see that the outer part of the rotor has been rubbing on the caliper bracket. This is happening on both front rotors. Could my new rotors be too thick or something?
View 4 Replies
After coming to a complete stop & starts driving again, I notice that the brakes squeaks a few turns & then stops. It seems that the brake calipers does not fully disengage from the rotors.
2006 Touareg V6 Silver
View 3 Replies
I have two 2002 ford Excursions, both with 7.3, one 2WD and one 4WD. I have replaced ALL brake calipers with lifetime warranty Napa semi-calipers. It is sometimes an intermittent problem, I might have smoking brakes on one wheel (mostly the rears) one day and it will work fine for weeks or months and then do it again. It seems that about 1X per year I end up having to replace the calipers as they seize up and cause the brakes to smoke and cooks the caliper piston boot to a crisp.
I use high temp brake caliper grease (not sure if it is silicone based) and bleed the brake system about 1X per year because I thought the brake fluid was absorbing too much moisture. The slide pins come pre-greased, but I always check and re-grease them. Could I be putting too much grease onto the slide pins, Hydrolock?
I live in high humidity, in the middle of a rain forest near (about 5 miles away) a live volcano, Kilauea, on the island of Hawaii. Our area is very wet and we have acid raid and acid air (H2SO4 volcanic smog in the air) which corrodes everything, corroded pistons getting stuck?
I have not tried other brands of calipers because I cannot afford to keep buying new brands, I just trade in the toasted calipers at Napa for no charge. I have replaced all the rubber brake hoses and i upgraded to DOT4 (not silicone based) blue racing brake fluid that has a very high wet and dry boiling point. I am thinking of investing in stainless steel calipers, but those are pricey.
View 4 Replies
OK, I just got back from having pads and rotors install on my '99 Passat. I was expecting this to clear up the brake and abs light problem but it did not. The brakes still feel mushy and the ABS light still comes on.What should I check? In the brake forum people suggested bleading the brakes, is this the next step? Any quick how to?
View 3 Replies
I need more stopping power. Is there a front caliper setup that you guys are using to get better brake performance? Either a direct bolt-in swap from a heavier vehicle (F350??) or a completely new aftermarket setup??
View 3 Replies
Just took a drive to Home Depot, hopped out of the excursion and got a whiff of burning brakes. I'm thinking i have a stuck caliper on the rear driver side just enough to cause the smell but not enough to slow acceleration or speed up deceleration. Should I just grease up the calipers?
View 14 Replies
Is it a do it yourself job to replace brake lines. Never done it before or even seen it done. Special tools required? Will the auto parts store know exactly what I need? Are these questions answering my question?(don't do it) ...
View 14 Replies
Driving home today I started smelling a burnt clutch smell!
Well since I have an automatic, I wasn't to worried until my 6 yr old gets out when we get home and says "DAD something stinks really bad out here!"
Get out and wow!! I have never had a caliper lock up on any vehicle I have ever owned! It stunk like I burnt a clutch out of a standard tranny!
So I start poking around and the left rear caliper is locked up, rotor is blue and you can hear it popping like a valve spring cooling down.
So my question is is there anything to look for other than the normal? I will be getting the brake system power bleed after I replace the caliper. I already checked the brake lines and there are no obvious issues. It is possible the rubber inner lining is toast.
View 14 Replies
I have a 99 150 4 wheel drive..5.4 ..auto...110.000 mile.....notice when driving in town in hot weather....when you are on and off the brake petal a lot....stop and go..etc.....the truck starts to hop or bounce....some....I got out ..and notice the right or passenger side front brake seems a lot hotter than the drivers side......but ...when it does that....the steering wheel doesn't pull to one side...when changing pads before ..notice no one side worse for ware than other...thinking it must be sticking brake calipers....they don't do this say on interstate driving even when on and off the petal some...
View 1 Replies
So I had a stuck caliper on the driver rear side. I pushed the piston back and checked everything to make sure all was in working order. After some though and reading about the calipers getting stuck which old brake lines, I decided to upgrade the line with the Russell stainless steal lines.
I got all the lines put in but I seem to have fluid leaking on the passenger side fitting which I can't seem to get to stop. I put the old line back in but it is still leaking. I am not sure what I need to do or check to get it to stop. It seems to be leaking from the thread area. I checked the fittings and they don't look cross threaded so I don't understand why it may be happening.
View 3 Replies
I have a 2001 mustang GT. I have 2 front calipers that are sticking. I changed both calipers twice, new brake hoses, bled all the wheels and the master cylinder. Why the calipers won't release?
View 19 Replies
My brakes sometimes feel like the rotors are warped. The problem is that it isn't consistent. I remember how the original rotors warped and they were crap so I put some drilled and slotted rotors on about 150,000 miles ago. Currently but not all of the time it acts like the current rotors are warped, the steering wheel will move back and forth, feel the shake in the vehicle. But today running a few errands at lunch, there was no wobble etc. I might go ahead and replace the rotors/pads but want to be sure that is the issue. Could it be the hydroboost on the 7.3? ABS?
View 6 Replies
I recently purchased an '08 F-350 4x4 Lariet Supercab 6.4l and was told by the 3rd party inspection that it needs rear brake pads (2mm left). Are the caliper pistons retractable without having the pistons seize down the road? HOw about the fronts? See below.
I ask as on my '06 F-250 XLT 4x2 5.4l the rear calipers seized without even doing a pad change and the fronts seized about 100 miles after a pad change. Come to find out it is a common problem with the '06 and the calipers either have to be replaced or rebuilt when changing pads. Now I've been "told" to expect the same with the '08.
View 8 Replies
Both of my rear brake calipers hung while traveling in mountains. Both so hot that I had no brakes. Had not been riding the brakes. Had to bump them when someone pulled out in front of me. Never noticed them hanging but smelled them and then hit the brakes and no brakes. They were so hot that they blew the valve stems out of both rear tires. Once they cooled, I had brakes. What would cause both to hang up at the same time?
View 1 Replies
Recently bought a 2001 Excursion 4x4 but failed to take it on the highway and get it up to speed. It shakes real bad around 65 but I can't tell exactly where the shake comes from. Here is what I've fixed so far. Balanced tires, Alignment, Fixed Steering Linkage, Balanced rear drive shaft, new shocks, new brake pads (slightly warped rotors but shakes w/o braking), lubed everything, replaced all fluids except transmission which was clean, no metal in any fluids, removed front driveshaft. Checked wheel bearing as best as I can.
View 5 Replies
We had approximately 7000 miles on our 2014 250 when we first heard our squeaking when we applied the brakes. This happened after we had been driving a while. Took it to the dealer to see what was causing the noise. They found out it was the front brakes. They removed both front wheels to find the inner pads wearing at an angle and the caliper piston boots partly melted in middle. They ended up replacing the brake pads and calipers with new and machined rotors.
View 14 Replies
i have the brake (!) the ABS and the VSC lit up after i got new bearings and new brake pads and rotors, the car was also stalling before the mechanic removed these bearing "dust cover" circles that must have been causing speed sensor interfernce bc the spedometer was stuck on 0....so the car seems to be done stalling after those were removed and all the big lights went off then i hit the brakes a few miles later and those three lights came on...
View 2 Replies
I noticed the front brake pads were touching the rotors when I was painting the brake calipers. I had my e-brake engaged and in park. I'm assuming the e-brake only brakes the rear wheels because the front rotors were still movable. Although the car still rides fine but I'm not sure if this is normal.
View 1 Replies
I have replaced booster, master cylinder, all four callipers, and bled the brake system a number of times on my 2000 F-150 4x4. and still the pedal is wicked spongy, is there some other problem?
View 6 Replies
I'm going to replace the rotors & pads on the X, was doing some research and read where slotted and drilled rotors actually create weak points in the rotor for vehicles this heavy.
View 14 Replies
