Ford Excursion :: Vacuum Fitting For Front Axle?
Feb 11, 2012
I need a vacuum fitting for the front axle..... Where I can get one besides a dealer ?
View 2 Replies
Feb 11, 2012
Advertisement
Ford Excursion :: Front Axle Leaking?
Noticed some spotting in front of the house, and saw some leaking coming from the driver side near the axle. I'm guessing it's the axle seal leaking. I recently switched in to 4x4 about a week ago, shortly after that I noticed the leak. I have a trip to San Antonio coming up in the middle of Feb, about a 650 mile round trip. Can I continue with the plans and get it fixed afterwards?
View 2 RepliesFord Excursion :: Front Axle Shaft U-Joints Won't Come Apart
its a 2000 limited 4x4, must have been in the snow a lot because it was from up north and is pretty rusty on the underside. my dad and i have tried everything to get these caps off but nothing will work. lots of pb blaster, hammering, even cutting the one of the four joints and trying to wedge something from the inside. If we cant get it could a shop do it? and how much might they charge?
View 9 RepliesFord Excursion :: Front Axle Gears Removal
Well the old ball ball joints are out, new ones are in and now I'm working on removing gear assembly so I can change the inner axle seals. I've been trying to get it out. It haven't had much luck. I've loosened the cap bolts, prayed, pulled, hit, and still no luck. The only thing I've been successful at is screwing up the first few threads of the bolt holes for the passenger side cap. Tomorrow I'll be getting a tap and chasing the threads to clean them up. Hope I haven't screwed it up too bad. How to get the gear assembly out?
View 8 RepliesFord Excursion :: Whistling Noise Coming From Front Axle
I am having a whistling noise coming from my front axle... It only happens when the hubs are locked and in 4WD when hubs are unlocked and in 4wd there is no whistling noise... I know they are vacuum operated for the auto hubs... We just got a good snow fall the past few days and have had to have the lockers locked to stay straight... Also can I keep the hubs locked and cruise and 55 to 60 mph ? or is it not good for the locking hubs...
View 2 RepliesFord Excursion :: Semi-Rounded U-Bolts At Front Axle
I fit yesterday my ProComp Leaf Springs 22415 in the back of my Ex. It took about 3hours with a couple of beers to get the work done. Are those springs huge and heavy.
I will change the front springs in about 2 weeks, but we figured out, that we will need there 4 longer Semi-rounded U-Bolts, because the leaf package is about an 1/2-3/4 inch thicker than the OEM-springs. My OEM are a 2Leaf Springs and those ProComps 22410 are 5 Leafs.
Ford Excursion :: Strange Sound Coming From Front Axle?
I've got a strange sound coming from the front axle. I want to rule out/in that it may be my auto lock hubs. Can I slide the hubs out and drive around? I dont see any problem I won't be offroad, just some miles to test it.
View 1 RepliesFord Excursion :: 2004 - Front Axle Inner Seal Replacement
I have an 04 Limited, 6.0 PSD, 4x4 which I need to replace the front inner axle seals, the right side is leaking out the shaft. I have watched a couple of YouTube videos on how it is done but would like to get some first hand knowledge and recommendations.
First, how important is it to check the backlash before beginning the removal of the gear assembly? Do I need to remove the pinion gear as well or just the gear assembly?
How difficult is it to get everything back on place once the seals are replaced? I have not done this type of repair before and am concerned I might miss something.
I am planning to replace all the ball joints at this time also, this was the primary reason for this maintenance in the first place.
Ford Excursion :: Passenger Side Front Axle Leaking Fluid
Its been awhile since I have been on. Everything has been running great for me until I found my passenger side front axle leaking fluid. I'm sure something has been posted on here but I have limited access to internet right now and need to know what I am getting into to change the seals. From what I have found there is an inner seal in the pumpkin and then an outer seal and dust cover. Are both of these easy to change? Are there any special tools needed? Do I need to remove the gears in the pumpkin? If so, is this difficult and any special tools required for this?
Mine is a 2001 V10-6.8, 4x4 no mods at this point.
Ford Excursion :: 2000 - Clunking Noise Form Front Axle?
I have a 2000 ford excursion limited when i drive a loud clunking noise comes from the front end, so i pulled the front passenger tire off and realized what looks like the axle bearing behind the hub assembly is rattling around. What part is that. I am going to post a picture tomorrow in the day light.
View 2 RepliesFord Excursion :: Circle Plastic O-Ring Behind U Joint Is Lose On Both Sides Of Front Axle
I noticed on my 03 excursion on both sides of the front axle there is a circle plastic o ring behind the u joint that is lose? Nothing is leaking and no signs of leak marks ever. Kind of looks lik a spacer ring of some sort because its at least 1/8th inch thick plastic. Also some time ago I posted about a whistling noise but never got a answer but its only there when im in 4wd there is a whistling noise from my right side and my locking hub when I turn it the hub seems lose and has a crunchy feeling to it. I just bought it a few weeks ago and now I am running into a whistling noise and noticed theres a piece of plastic that looks like a spacer....
View 14 RepliesFord Excursion :: Clicking Noise Coming From Front Right Side Tire - Excessive Play In Axle
I have had a Clicking noise on my 2000 x 4x4 since 6 months coming from the front right side tire noticeable over rough roads or over bumps and I went on a journey starting with ford dealer to almost all well recognized service centers and every body says your front suspension is ok and no one seems to know where it is coming from. I thought it was my hub bearing since it fails almost every year but when I was changing the bearing, I noticed a big Excessive play in axle.
See video : My AXLE Shaft - YouTube
Also I noticed oil mixed with grease the grease is prawny with a reddish sort of color or that is some thing else.
See photos ....
Any way after replacing the hub Bearing with a used one and butting every thing together I went on a test drive. Noticed that the vehicle drive line is not right the car seems to wonder and the noise still there so i didn't get far i came right back and park my x then a funny burned oil smell was present.
Is it some thing i did wrong or is it bad situation gone worst ?
Items Checked Or Replaced In The Last 4 Months ( trying to fix)
Tie Rods. Ok
ball joints. Ok
suspension front and rear. Ok
Front stabilizer bar. Ok
control arm bushings. Ok
stabilizer bar bushings Ok
steering linkage. Ok
brake pads. A new front set installed
Rotors . Both front changed with oem parts
body mounts + sub-frame mounts. Some replaced
shock absorbers . New 4 set installed
- Rear Monroe 911176 Reflex Light Truck Shock Absorber
- Front Monroe 911175 Reflex Light Truck Shock Absorber
tires. Replaced with a new set off four
Hub Bearing. Second hand (that's when I saw it)
Spare Parts waiting list (Ordered):-
O ring ord part # 4C3Z-1K106-AA
(knuckle seal) (F81Z-3254-CB).
and some other dust seals which i can't recall.
I am looking for how to fix axle play and get red of the noise. (this is a video from you tube for clearance)....
F250 wheel bearing, is this bad or not? - YouTube
Ford Excursion :: After Standard Brake Line Replacement Fluid Leaking On Passenger Side Fitting?
So I had a stuck caliper on the driver rear side. I pushed the piston back and checked everything to make sure all was in working order. After some though and reading about the calipers getting stuck which old brake lines, I decided to upgrade the line with the Russell stainless steal lines.
I got all the lines put in but I seem to have fluid leaking on the passenger side fitting which I can't seem to get to stop. I put the old line back in but it is still leaking. I am not sure what I need to do or check to get it to stop. It seems to be leaking from the thread area. I checked the fittings and they don't look cross threaded so I don't understand why it may be happening.
Ford F-150 - 1997-2003 :: Front U-Joint On Rear Drive Shaft Has Grease Fitting
I recently bought a 1997 F150 4wd 5sp manual. While changing the fluids, I noticed that the front u joint on the rear drive shaft has a grease fitting. No matter how I rotate that shaft, I cannot access that fitting with my grease gun, even when fitted with a flexible rubber hose.
View 14 RepliesFord Excursion :: Stuck On Defrost Vacuum Leak
Ok, I have capped off the vacuum lines to the front hubs and replaced the vacuum solenoid on the passenger inner fender. Still stuck on defrost. I know there are several options from this point what would be the next step after what I have just recently done. Going away on a ski trip and would like to have it working properly before I go.
View 14 RepliesFord Excursion :: 4 Wheel Drive - Vacuum Seal Is Out
I have an 02 4x4 excursion. How can i tell if the 4 wheel drive is working? If I turn the switch I dont feel any change. Also sometimes I hear air coming up near the defrost at the base of the windshield which makes me think maybe the vacuum seal is out. Also how can I check/change the hubs between manual and auto and what applications would warrant switching them?
View 11 RepliesFord Excursion :: Axle Alignment Procedure?
I had additional springs added to the front axle by a shop that I would not now trust to work on a tricycle.
The front axle was installed at an angle.
Is there a recommended procedure to align the axle? The two ideas I can guess at is to find a centerpoint on the body or frame and use that as an alignment point like one would align a trailer axle to the hitch or to assume the spring mounting points are precise enough to just center the axle between the two on each side.
Ford Excursion :: Vacuum Leak In The Lines Coming From Electric Pump
So, my original pump finally died and I replaced it....however upon doing so I realize there is a leak/crack in the lines as it never shuts off (explains why the factory one died).
After a bit of troubleshooting, I've discovered the leak HAS to be down in the passenger fender where the black and grey lines travel over the blower housing and go straight down up against the inner fender wall.
Where doe these come out or connect? I clearly cant get a hand down in there...does the inner fender well have to come out to access this? or is there a junction box/splitter somewhere accessible?
Ford Excursion :: Sound And Vibration While Driving Forward - Possible Vacuum Leak
I have been having some issues I think are vacuum related but I'm not sure how to correctly diagnose or pinpoint exactly where the problem is. 2 issues that seem vacuum related:
The first is a sound and vibration I get while driving forward. While the wheels are moving, it sounds just like a baseball card in bike spokes, it usually happens after I backed out of a parking spot and put it back into drive. I will get that sound and vibration until I slow down, and just as I begin to stop, I feel and hear a big bump and the sound goes away.
The second is the old climate control settings. The settings switch without moving. Sometimes while I have the AC running through the dash vents it will switch to the defrost setting and then back to AC after a couple minutes. Sometimes it won't stay in the defrost setting and switches to the vents. How to diagnose?
Ford Excursion :: Rubber Seal Near Axle Joint?
I unstuck my front axles yesterday and while under the car spinning the front axles freely and enjoying my easy fix, I noticed a rubber seal (a thick squared edge round rubber seal) sitting loose and spinning freely. Its next to the axle joint, right before it disappears into the housing.
I'm guessing this is a dust seal of some kind. There is no fluid leaking out...
I'm wondering if I can just press fit this thing back into place or do I have to take the whole front wheel assembly (hub, bearing, axle, etc) to get the seal back into place.
I'm wondering if it broke off from a larger seal or if this is the whole thing? You can see how the seal isn't sitting quite straight. It actually just spins around.
Ford Excursion :: Slight Leak Just At The Axle By The U-Joints
Our axle seal went out 2500 Miles ago. Its a light leak and just wets the axle by the U-Joints. Also our 4x4 hubs don't kick into action when they should. I have to put them in Lock to get them to work. That may be why the axle seal went out, because I just leave it in lock then drive thousands of highway miles. (I don't do that anymore now that I know what I was doing) Maybe the vacuum isn't working. Could they have anything to do with each other? I don't think they do. I'm not sure how the vacuum works. Maybe I just need to service the Hub? I watched a video on it that made it seem like cake. New hubs crazy expensive!
View 8 Replies