I am looking at a used 2003 X with a 140k miles. The truck is very clean and seems mechanically sound. This will be my third X! The only problem I found is the trans selector is difficult to move. Once driving the trans seems fine. No leaks anywhere. I believe this is cable actuated? Is this something minor or should I run away?
View 14 RepliesMy 2004 Explorer XLT 4.6L V8 AT is very difficult to shift out of park. Sometimes I have to push very hard on the brake in order to get the transmission selector out of park. Other times it is no problem.
View 1 RepliesI am just about committed to purchasing a 1997 Ford E350 extended cargo van with the 5.4. The transmission shifts through all the gears nice and firm (reverse also works). The only issue with the van is the column selector lever is very hard to move between the entire range of PRND21. It also does not "click" into the selected positions, you have to just line up the pointer to the desired gear selection.
Is this a complete deal breaker (internal transmission issue/replacement necessary) or, is it something relatively simple (such as a worn selector cable). The owner did admit the van has been sitting for sometime. It has 134,000 miles on it.
Fix a Loose Column Shifter on Ford Vehicles - YouTube
The first pic shows the torx screws that come loose, allowing the handle to get sloppy.
The second pic shows the black plastic adjuster wheel that centers the gear shift selector needle on the proper designated gear displayed in the indicator window.
Parked truck, went to leave and truck starts and runs fine, says brake problem on message, wont let me move gear selector out of park, is there a way to do this manually and get it to neutral so it can be towed??
View 2 RepliesI have a 2003 f250 and I am unable to rotate the hubs from automatic. I have removed them and while I had them apart, I was still unable to rotate the selector. It wouldn't turn even with a crescent wrench putting pressure on it. I repacked them with grease and reinstalled and they still work when in 4 wheel drive. I am just concerned that when the vacuum does go out, I will not get the hubs to manually lock in.
View 10 RepliesHere is what I have:
2009 Santa Fe 3.3L AWD
70k KMs / 43k Miles
Temp has been very cold, -20C / -4 F
Car starts up without any problems. Try to put car in Reverse and the shifter is very hard to move, if it moves at all. When I am able to get it into Reverse, I then try to put it in Drive and it does not "engage" the "D" and the car behaves like its in Neutral. Moving the shifter back to Park, Neutral, Drive is very difficult and sometimes it will not go into Park. The dash lights do not illuminate the selected P, R, N, D.
However, once the car is warmed up (no longer on C on the temperature gauge) I can with a little effort move the shifter freely (but more effort than it should take) and the car behaves normally. Gear shifts are smooth and in general it is operating normally.
The dash lights do illuminate the selected P, R, N, D. I've checked the Trans fluid level and it appears to be normal and was planning to change it this w-e but I'm no longer sure it will work. Even if it has never been changed.
Also note that I have recently changed a wheel/hub bearing due to a noise that sounds a lot like loud tires on a highway. The bearing change did not eliminate the noise and I assumed that I've changed the wrong one. The noise does not appear to be coming from the Trans, but I cant be 100% sure. The noise is speed related and occurs only after about 20KM/h 16MPH. Unsure if they are related..
What does it mean when the PRND2 area all illuminated at the same time? Normally only the gear selected will be illuminated, but yesteday I got a solid bar illuminating all the gear selections. Couldn't find any reference to it in the manual. Shut the car off and restarted and the problem went away.
View 24 RepliesI am Having a problem on my 2005 Phaeton which has a 3.2 engine. Last time I drove it was yesterday and had no problems. This morning, I'd turn the key and it give me various error message."Move selector lever to position P/N" ...
I tried to move it but with no luck , the message is still there and I also noticed that the light on the shift that indicates that I need to press on the break to start is not glowing. This is not the 1st time I had this error but before I had to leave it for a while and it will start ...
I really love my Phaeton and it has only 75,774 kilometres on , so it is quite new ...
You can see the error message and the light indication below in the pictures ....
I have a European Phaeton 3.2 litre V6 (gasoline) from 2003 that is giving me some problems. When I am finished driving I put the gear lever to parking position and turn off the ignition. I then get a message "Move selector lever to position p" and the key is stuck in the ignition.
So far, I have been able to get the error message away (and with that also been able to get the key out) by starting the car and move the gear lever around. Some times I have managed by only starting the system (by not holding my foot on the brake pedal). But tonight I couldn't get it fixed after numerous tries. I then simply waited in the car, because I didn't really know what to do, and after maybe five minutes the system shut down (energy saving mode?) and I could finally get the key out.
When I tried google the error message I found some topics about it on the Touareg forums, but they got the error message while driving and it had to do with the keyless system (which my car doesn't have).
What might be causing this problem? My local VW dealer is not very used to Phaetons (I am the only on in my town with one).
Today when I head home I was getting the message "Move Selector Lever to Position P." It would come and go. No other lights or warning what so ever were lit. What this message was for and why it was displaying??
View 6 RepliesLast night I jumped into my Treg to move it into my garage. When I pushed the brake pedal to move the gear selector out of park, I heard a whooshing sound. Like the sound of a bellows-type foot pump I use to inflate my dinghy. I could also feel a slight amount of movement in the transmission lock button on the top left side of the shifter when doing this.
Now I'm noticing this noise whenever I apply the brakes. It doesn't appear to affect braking performance, but does have me wondering. I'll have the dealer check this out when I take the Treg in for the recent recall (got my notice yesterday).
I have a 2006 Mustang (manual 5 speed) that recently has been having a problem getting into 1st gear
Symptoms:1. When the engine is cold, there is no issue getting the car into gear2. Once it warms up (after approx. 20 miles or 30 minutes driving), it is very difficult to get into 1st gear. I have to put it in 2nd then get it to slip into 1st.3. On hot days the problem starts sooner and is hard to get into the other gears4. when the car has warmed up on a cool day. I can get the car into the other gears (2nd, etc) when standing still, but first is almost impossible
Originally the problem showed up when my wife drove the car, but it is getting worse. Why the engine and/or outside temperature would affect how my I can get my car into gear?
I had a clutch, slave cylinder, and master cylinder replaced about 20,000 miles ago. Everything seemed to be working fine until I drove across the Rockies. The transmission was extremely difficult to shift, and the vehicle would actually roll forward when cranking the engine at fuel stops (temps were minus twenties). Once I got out of the mountains on both ends of the trip (where it was warmer), the clutch worked normally. The local Ford dealer found lots of air in the hydraulic clutch system, bled it, and it worked fine for several months.
The clutch is doing the same thing currently, but not all the time. Some days it's fine, other days it's difficult to shift although double clutching seems to work. It gets particularly hard to shift after a long drive (e.g., interstate driving for a couple of hours). I took it back in this morning to see if the dealer could figure out what is going on, they're saying it's likely a bad slave cylinder. I've heard the 1995 Explorer clutches are a bear to properly bleed, and can't work but think there may still be some air in the system.
I just got my 03 F-150 with 112k on the clock. It has the manual 5 speed tranny behind the 4.6L.
However, since I've gotten the truck, it's kind of difficult to put in first gear. If you are sitting at a light and in neutral and the light changes and you push the clutch to the floor and put it in 1st (fairly quickly - a normal reaction time), it will actually do a little grind and/or thump. However, if push the clutch to the floor and wait a couple of seconds and then shift into first, it's a bit of a "push" but it will go in without grinding.
Once in a while shifting to 3rd it feels the same way, but won't really grind.
I'm just wondering if that means the clutch is toast or is it the trans that is toast? Reason I ask is my 96 Cobra with the T-45 5 speed would grind going into 5th gear if I just normally put it in. I used to have to put it in neutral and then push the clutch in again and slowly shift to 5th for it not to grind. And it wouldn't go into 3rd if I tried to shift fast or under power. I replaced the clutch and found out the trans was actually going bad, but it had 173k on the clock.
So, I'm really paranoid that it's my darn trans in the truck instead of just the clutch. Whenever my old Camaro clutches used to be dying, they would slip more than they would ever grind going into a gear.
My son has a 2008 Ranger 4.0 4wd 5 speed. Every month or so we need to bleed the clutch as the transmission becomes very difficult to shift. It does not lose fluid, but seems to be holding air. And it's not easy to bleed this setup. Slave going bad? I guess the transmission will need to come out then.
View 3 RepliesI have a 2001 Ford Excursion with the 5.4 and auto trans. I don't know for sure what specific tranny is in it but I do know what I want to do. I really like the pistol grip style shifters that a 2004 ish F-150 has and I wanted to make that conversion in my Excursion. Is it possible? Are the trannys the same to where I can switch out the gear selectors? And also how would I even do it?
View 7 RepliesScenario.... Anticipating needing 4wd, I turn the selector to 4wd, proceed forward, and pow, a huge pop from the front end. I proceed about 5 feet, and am stuck in mud without front wheel engagement. I manually lock hubs and have 4wd. Is this the leaking hub vacuum, I hear so much about? What was the popping sound? Any harm done? Everything locks, lights up, then disengages...... A little freaked out!
View 1 RepliesI have a 1974 ford f100
302
fmx transmission 14 bolt pan
tag off of transmission (not sure if this tells you anything)
The problem: the selector shaft is leaking
What I need: a replacement seal - part number or where to buy
Also, when I remove the valve body to replace the seal will there be any hidden BB's, springs or any other things come flying out that i need to keep an eye on. Valve body torque specs would be fantastic.
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 RepliesI have a 1997 F-150, 2 wheel drive, 4.6L truck. Recently the transmission got to where it didn't shift properly. Then it got to where, after driving it about 10 to 15 miles the transmission would drop out of gear with the transmission selector in drive.
I have replaced the transmission sensor, the rear end sensor and it still does the same thing. Drive about 10 to 15 miles and, with the transmission selector in drive the truck will not pull. The motor can be rev'ed but the truck won't move just like it was in neutral.
What is wrong. The transmission shifts fine, the truck runs fine, but after 10 to 15 miles the transmission quits working.