Ford Excursion :: Sputters And Dies / No Response When Hit The Gas
Mar 7, 2015
Okay so I ran my excursion earlier this morning and it ran fine and what have you, and now 6 hours later I got to start it up and it sputters and dies. I start it again and it starts right up but then goes to sputter again and I hit the gas and it didn't respond, the RPM gauge was lingering just under 500 RPMs. I had to hold the gas pedal for about 15-20 seconds before the engine would rev up, it kept doing this till the engine finally warmed up and I drove it up and down my block with barely and throttle and with wide open throttle and it ran fine. With the engine warmed up it started with no problems. I have a 2000 5.4L V8 gas
View 5 Replies
Advertisement
My 08 escape (3.0) wouldn't go over 45-50mph Sunday on my way home. The next morning I made it about 2 blocks and the battery light came on and it died. I am replacing the battery tomorrow because it tested bad but believe there is also an exhaust problem. Last week it began making a noise I could hear inside the car only when accelerating. Almost sounded like a small,air plane. The car will start and run now but cuts out and sometimes will Rev up when I press accelerator and sometimes won't. The exhaust pipe gets hot really fast and it and the motor both vibrate we the car is started (more than normal) any clue on where to start??
View 1 Replies
I have been having issues with my 2001 sports trac 4x4 v6 sohc fuel in. 132k mileage. The problem is I can jump in and it will start first try, fuel pump is heard activating, idle is rough, feels like truck is about to die, pumping on the gas usually causes it to catch and smooth out......after 10 mins. or sometimes less than that truck starts to sputter, step on throttle it dies faster, sometimes when stepping on the throttle before it dies and a truck is able to rev up and then back to idle and not die.
But most times stepping on the gas when it begins to sputter after running for 10 mins or so causes it to die once it dies it doesn't start back up and when key is turned on and off, no fuel pump activation noise. I have scantool data take off an autel 619 saved to notebook text format. Those are my numbers for the scan tool, suggestions I have gotten so far are vacuum leak, failing fuel pump, bad o2 sensors, bad MAF.......so far replaced fuel filter and cleaned MAF....no difference.
View 11 Replies
I have had a 2005 f150 v6 5 speed for a little over two years. Got about 153k on it. Last night was sitting in a parking lot idling about 20-25 minutes, went to leave and she started sputtering hard, lost all power and died. Started back up, idled fine, as soon as i put it in gear same thing then the check engine light came on.
View 3 Replies
2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?
View 14 Replies
Drove the car, 20 min to shopping, and when I came out the car would sputter and die??!! it happened a few times.. it would crank for really a long time, engine would fire up but sputter & die. I was cussing & let the car sit at mall parking lot for a bit, thinking I'll have to cab home but it started up again after 10 min and drove fine. It happened on a parking lot, not on the highway.
View 24 Replies
I have a 95 Volvo 850 2.2 L (non-turbo.) I recently replaced the fuel pump, and filter. Now when I try to start the engine, it turns over and sputters before it dies. I let it sit for about 10 minutes and try again with the same results and the same with a longer wait time due to having to charge my battery. I have checked the fuel lines and they seem to be clear, up to the fuel rail. I also checked the plugs and although they need to be replaced, after sanding and re-gaping them, there is plenty of spark. The plug wires and distributor cap are fairly new, and the points look good. So the only problem I see as logical, is the fuel rail, pressure regulator, and injectors. I have bled the fuel rail at the shrader valve, and I am getting little to no fuel from it. I want to remove the injectors and rail, and check out the regulator along with the rest. But how do I tell if the regulator is good, and what is the best way to clean injectors so they will at least last till I can replace them with new?
View 2 Replies
'99 Intrigue (3.5L) with 65k miles. The car has sporadic starting problems where turning the key in the ignition turns the starter motor and results in one of the following scenarios:
1) The engine does not turn on.
2) The engine turns on, RPMs drop and the engine sputters and dies.
3) The engine turns on with no problems (like this morning).
It does not appear to matter whether the engine is hot or cold.
Reading forum posts of people that have seen similar problems, several different solutions would seem to be in order:
1) Replace fuel pressure regulator.
2) Replace crankshaft position sensor
3) Replace camshaft position sensor
4) Replace fuel filter
5) Replace spark plugs
6) Replace idle air control valve
7) Clean the throttle body
Since I rather not start throwing money at the car by replacing parts one by one until the problem is gone.
View 11 Replies
My Honda has a strange problem that is vexing my mechanic. While I am driving, the engine spits and sputters and sometimes dies. I try to restart and it starts right up but runs rough. Sometimes it takes a while to start back up. If I wait a few minutes, it will start again and drive fine for a while. Then it will do it again. After it is warm or when it is cold at the start, it won't do it.My mechanic cannot get it to do it long enough to diagnose. The computer is not throwing any codes. I believe it is electrical because when it does this, the speedometer goes crazy bouncing up and down. Electrical problem also may explain why the computer is not throwing any codes. I need to narrow it down because my mechanic is reluctant to start trying things as I don't have a lot of money to throw at this.
View 4 Replies
I purchased a 1990 Jeep Cherokee Laredo at a steal . . . I've already replaced the head gasket sealant. My biggest current concern is the fuel pressure. The car either starts up beautifully or sputters and gurgles for a good 5 seconds before finally idling normally (either occur during cold or warm starts).
The sputtering at start-up has become more commonplace as of late. If I drive away without providing a good three-to-five minute warm-up, the car will drive as normal while applying gas pressure to the peddle, then once gas pressure is no longer applied, the car dies silently; The battery stays on, but all power steering and engine power disappear and the car coast into nothingness. If I allow the Jeep to warm up significantly, it will drive as normal for hours, except for it's struggles to compensate long upward hills.
The fuel regulator has a slight leak. Worse at start-up, lessens up over time. The seal may be improperly seated, but is in physical working condition as I can tell. Spark plugs were replaced. Battery was replaced. Injectors have been tightened. There is a slight oil leak (it seems to move around a bit), but is far better since the Head Gasket was replaced. Could this be a bad fuel regulator or something else that I have missed?
View 1 Replies
Finally had a chance to pull the coils for inspection, and give the truck some very needed plugs. anyways, since i got it, the truck on initial start will rev itself up to about 3k rpms. it will almost always die after that rev. with the MAF sensor disconnected, it will rev to about 2k rpms, and the idle, if you can call it that, around 1k rpms. it will buck, jump, spit, burp, chug, pop, blow, and phew noises the whole time. I can rev the truck at this point but the throttle repsonse is poor. it does rev with a slight misfire, but no popping like what it does at idle. the exhaust has been dropped before the cat, so i know its not a plugged cat. i feel it could possibly be a sticking idle control valve allowing air past behind the MAF sensor causing this crazy scenerio
View 7 Replies
i have a 04 ford excursion 6.0 with the egr delete, was stopped at a light to make a left turn, when i stepped on the accelerator pedal nothing happened as the engine was just idling. i pumped the pedal around 10 times and finally got the engine to rev up. i just got this excursion and don't know to much about the maintenance on it. i am going to drain the water and change the two fuel filters. my neighbor is familiar with diesel engines and he said to look at the throttle sensor. i have run this engine up to 900 miles and it has started and run perfectly. i believe the usual maintenance like oil changes etc were done on it. would any error codes show up even though no warning lights on the dash.
View 8 Replies
I have a small problem that has been going on for about the last 6 months. It only appears once in a while, and only when I have parked facing uphill for longer than a day or so. Upon first start (cold) after sitting pointed uphill for a day or two, it starts real rough and sputters a bit. Then when I check codes, I always have a pending P0316 (misfire within the first 1000 revolutions) along with a P0306 or P0301. No dash lights or anything.
Since those two cylinders are at the front of the motor, could it be that the fuel is leaking back down the rail and leaving those two injectors dry? It isn't always both cylinders, sometimes one or the other. If this is the sign of something bigger on the horizon, I would like to have a heads up.
View 5 Replies
I have a 2000 excursion V10. It will die in gear forward or reverse the overdrive light flashes and cel shows code p0720. I have new plugs and COP on all 10 cylinders. I have replaced the differential speed sensor and the sensor on top of the transmission. I have a basic code reader it shows at the time it dies the vehicle speed is 70 mph while the speedometer shows 0. When I unhook the abs module it still has code p0720 but it does not die. I am replacing the abs module?
View 8 Replies
I have a 2000 V10 ex. The past couple if days it been giving me some issues while trying to start. At times it will start fine like every truck should, but every now and then I turn the key and it starts to catch but quickly dies. Then it continually turns over. I apply pressure to the gas and it finally catches and runs fine after that. This problem has been getting worse over the past month. Whenever I start it I have to apply gas before turning the key so I know the engine will catch. I've already added fuel treatment and stp to clean fuel pumps but had no luck with that.
View 6 Replies
My 2001 Ford Excursion won't start I put a brand new battery in it it started to crank then dies down like it starting to drain my battery what could it be?
View 1 Replies
I have a 2002 Excursion 7.3 4x4 and when it will start is runs for about 20 min then turns off. When I go to start the truck again the theft light flashes rapidly and the glow plug light never turns off. I have tried reprogramming the key to the PATS by leaving it turned for 30 minute then turning it back then starting and that worked for a few times but it doesn't anymore. Additionally I used to be able to take the terminals off the batteries for 20 minutes or so and then it would start after re connecting them but now I have to leave the batteries off for like 24 hours then it will start fine 1 time run for 20 minutes and die and won't start all over again.
I have a snap on solus pro I am borrowing to figure it out but am not very familiar with it, I can only find codes P1876 T-Case 2wd Solenoid circuit (but mine is 4x4) and U1262 data fault for J1850 there is nothing pulling up under the PATS option in the scanner so I don't know whats wrong or where to even begin, it just shuts off.. The truck runs great till it shuts off, buzz test in the scanner doesn't do anything and neither does the glow plug test. When the truck dies is just turns off like someone turned the key off, no running rough or anything first, I am pretty sure the computer is shutting off the injectors and then locking me out.
View 7 Replies
My tranny guy just did a full scan and the ONLY thing which indicated a problem was 'output speed sensor' which we were able to trace back to most likely being caused by a completely hosed driveshaft (I've noticed a driveline vibration). We're going to install a new driveshaft, replace the output speed sensor(s), check for any frayed/chaffed wiring going to the output speed sensor(s) and then see where that leads us (he said something about some computer module in the dash which he's had to replace on several Sooper Dooties).
View 7 Replies
2000 X V10 4WD... 178K. Truck was not well maintained for most of it's existence. Drained both the TC and Drain pain and replaced the oil filter. Tranny oil looked like crude and a lot of tiny specs of metal - it shimmered in the sun... needless to say - I'm pretty sure it had never been changed.
Now - issues since I've gotten it done... Tranny has been slipping... I figured that I may not have filled it enough and after adding a few quarts, it seems to have stopped. Slipping was initially just when going from a stop.
Now it's having a problem where the engine dies when I shift from one position to another... For instance - from Park to Reverse, the engine RPMs drop as the clutch engages - but they drop from about 900 RPM down to about 500. And 50/50 chance the engine dies. Going from Park to Drive, the same thing but maybe drops to about 700 RPMs. Tried it in 2nd and 1st gear. Has happened in both. I've tried shifting to OD first before going to 2nd to 1st or vice versa and seems to behave better.
Should I flash the ECU and have it relearn the shift points? Did I overfill? Between the TC and Drain Pan - about 16 qts came out. I've been checking the dipstick - no frothing or bubbles. When running and in park - it actually shows low. Seems to drive fine once it's on the road. The engine cutting off when it's put into gear is really unexpected.
View 13 Replies
I have an 02 X, and it's been giving us trouble for almost 2 years now. We've babied it along, but it is acting so crazy now. Here's the current weirdness...
Truck idles, ABS light comes on, within 15 seconds engine dies. Battery is DEAD, must have a jump to restart. Otherwise, if we catch the ABS light and Rev the engine to 2500 rpm and hold it for a few seconds until the ABS light goes out, then it is fine and does not die.
We have replaced the alternator with a stock Ford brand (whatever their brand is from the dealer) because we were told the ones from the auto part stores didn't have a strong enough or steady enough current. (This thing had already eaten 3 auto parts store brand alternators in 2 years.)
View 14 Replies
My 02 6.8 v10 4x4 4.30 X has a big problem. I was driving on sand and all of the sudden it stopped and dies. Had no trans fluid and a dead battery. After paying $450 to get it off the beach i filled the trans fluid and got a jump and it runs. When put in gear wether in 4WD or not it does NOT move. Only when put in neutral and pulled ... red dot is pavement, blue is where i got to, star is where i broke down on the way out...smh
View 7 Replies
